Manuale d’uso / di manutenzione del prodotto FM100 del fabbricante Newland
Vai alla pagina of 127
FM100 1D CCD Fixed Scan Engine Integration Guide Pre-release V ersion 20100824.
nlscan.com Page 2 V ersion Description Date Pre-release Initial release 24-08-2010 Revisions.
Disclaimer © 1999-2008 by Newland Auto-ID T ech. Co., Ltd, All rights reserved. No part of this publication may be reproduced, transmitted, or used in any form or by any means, electrical or mechanical, without prior written permission from Newland Auto-ID.
nlscan.com Page I 请更换节标题 T able of Contents Content About this guide Introduction ................................................................................................................................................. 1 Graphic Notations .
nlscan.com Page II T able of Contents Communication Programming Introduction ................................................................................................................................................ 29 Serial Port Programming ..
nlscan.com Page III T able of Contents AIM 128 Code ID ............................................................................................................................... 50 Select Message Length ...........................................
nlscan.com Page IV T able of Contents ITF-6 .......................................................................................................................................................... 71 ITF-6 Code ID ...................................
nlscan.com Page V T able of Contents T ransmit Start & Stop Character......................................................................................................... 93 Select Message Length ...............................................
nlscan.com Page 1 About this guide Introduction This FM100 1D CCD Fixed Scan Engine Integration Guide provides general instructions for OEM integration. Graphic Notations T ool – Handy item for a task. Attention – Important subject to be aware of or to avoid.
nlscan.com Page 2 About this guide Newland Auto-ID Support Center If you have a problem with your equipment, contact the Newland Support Center in your region. Before call- ing, have the model number , serial number, and several of your barcodes at hand.
nlscan.com Page 3 Getting to Start Introduction FM100 is a 1D barcode reader . Newland Auto-ID patented T M technology ensure FM100 fast image capture and accurate decoding. It provides the customer the best value. This chapter presents an overall picture of how to use FM100 step by step.
nlscan.com Page 4 Getting to Start Unpacking Unpacking Unpack FM100 and accessories. Check with the packing list. Make sure that there is no damage or missing part(s). If any damage or missing parts, please keep the original package and contact your supplier for services.
nlscan.com Page 5 Getting to Start Unpacking Data Interface Pin Function T ype Name 1 NC Null 2 NC Null 3 VCC P Power DC5V 4 TXD O Serial Port Output , RS232 5 RXD I Serial Port Input , RS232 6 NC.
nlscan.com Page 6 Getting to Start Communication Ports FM100 must connect to a Host to operate. A Host can be PC, POS, or any intelligent terminal with at least one of the following communication ports: USB, RS232, or PS/2. USB 1 、 RS232 2 、 RS232 port on Host : Please check the ports first to order the fitting cable.
nlscan.com Page 7 Getting to Start Connecting with USB Cable Insert USB Cable (RJ45 male head) into FM100 cable slot; 1 、 Insert USB Cable (USB male head) into Host ’ s (female) USB connector; 2 .
nlscan.com Page 8 Getting to Start Connecting with RS232 Cable Insert RS232 cable (RJ45 male head) into FM100 cable slot; 1 、 Insert RS232 cable (RS232 male head) into Host ’ s (female) RS232 conn.
nlscan.com Page 9 Getting to Start Decode Zones 42 ° 0 100 200 300 400 500 55mm Code 39(10mil) 315mm 65mm EAN-13(10mil) 250mm 95mm EAN-13(15mil) 310mm 60mm Code 128(10mil) 280mm 40mm Code 39(15mil) 4.
nlscan.com Page 10 Getting to Start Specifications Performance Interface RS232, USB 1.1 Image Sensor CCD Resoluing 2500 Symbologies Code128, EAN-13, EAN-8, Code39, UPC-A, UPC-E, Codabar , Interleaved 2 of 5, ISBN/ISSN, Code 93, UCC/EAN-128, GS1 Databar , etc.
nlscan.com Page 1 1 Getting to Start Dimensions of FM100 Unit FM100 T op V iew Figure 1. 5 0m m 6 0m m 2 6m m 1 2m m 1 0m m 9 m m 3 6m m 1 1 7 m m . M3 machine skew.
nlscan.com Page 12 Introduction There are 2 ways to program (configure) the Engine, Code Programming and Command Programming. Code Programming The Engine reads a set of specially encoded barcodes to program options and features. In the following sections, we will explain the options and features available and provide the barcodes to program them.
nlscan.com Page 13 General Programming General Programming T ools Code Programming ON Code Programming OFF Programming Notation Th is i s t he n ot ati on t o d is ab le th e Co de Pr og ra mmi ng . Th er e are 3 p ar ts of a no ta ti on : The barcode for Code Programming 1 、 The name of the options or features, such as Disable Code Programming.
nlscan.com Page 14 General Programming General Programming T ools Code Programming ON Code Programming OFF Code Programming Re ad t he “ C od e Pro gr am min g ON ” bar co de to a ct iv ate “ Co de Pr og ra m- mi ng ” fun ct io n. Mo re t han o ne C ode P ro gra mm in g bar co de s can b e rea d to co nf ig ure t he E ngi ne .
nlscan.com Page 15 General Programming Command Programming Commands under RS232 connection mean using 0x20-0x7D ( the displayable characters ) to express all commands information. Configuration State 1 、 The engine should be in configuration state when programming functions under RS232 connection.
nlscan.com Page 16 General Programming Command Programming 3 、 Fl ow Ch ar t Non-Configuration State Configuration State Host sends “ $$$$ ” and receives “ @@@@ ” 5 seconds timeout , recei.
nlscan.com Page 17 General Programming General Programming T ools Code Programming ON Code Programming OFF Default Factory Default Read “ Load All Factory Default ” to reset all parameters to factory default.
nlscan.com Page 18 General Programming General Programming T ools Code Programming ON Code Programming OFF W orking Mode Shut Down 1 【 Pro CMD : 99900100 】 Deep Sleep 2 【 Pro CMD : 99900101 .
nlscan.com Page 19 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Auto Mode First program the engine, then trigger it, the engine will start to scan. After a scan, the engine will not stop but start a new one automatically until another trigger .
nlscan.com Page 20 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Interval Mode After programming, the engine will start interval scan without trigger . The interval between two scans is fixed whether the scan is successful or not.
nlscan.com Page 21 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Sensor Mode After programming, the engine will start to sense the environment without trigger . After a scan, it will stop and keep sensing to wait another illumination changing.
nlscan.com Page 22 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Continuous Mode 【 Pro CMD : 999001 14 】 Continuous Mode After programming, the engine will be in continuous mode without trigger .
nlscan.com Page 23 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Delayed Sensor Mode After programming, the engine will start to sense the environment without trigger . There will be a delay before a scan.
nlscan.com Page 24 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Command T riggered Mode After programming, when FM100 receives trigger sweep command from terminal ( e.g. PC ) or read "Start Analog T rigger" barcode, the engine will start to work.
nlscan.com Page 25 General Programming General Programming T ools Code Programming ON Code Programming OFF Security Level Security Level 1 【 Pro CMD : 99900120 】 Security Level 2 【 Pro CMD :.
nlscan.com Page 26 General Programming General Programming T ools Code Programming ON Code Programming OFF Beeper No Beeper Output 【 Pro CMD : 99900130 】 High Frequency & Loud V olume 【 Pr.
nlscan.com Page 27 General Programming General Programming T ools Code Programming ON Code Programming OFF Others Start/Stop T emporary Mute Start T emporary Mute 【 Pro CMD : 99900040 】 Stop T e.
nlscan.com Page 28 Query Command Introduction After reading interrelated programming barcodes, the engine will feed information needed back to the Host to achieve the purpose of query .
nlscan.com Page 29 Communication Programming Introduction Under RS232 connection the engine and the Host use the same communication parameters: baud rate, parity check, data bits select and stop bits select.
nlscan.com Page 30 Serial Port Programming Communication Setup Baud Rate Under RS232 connection, the engine and the Host should set communication baud rate to the same to keep normal communication. Baud rate is the bits transmitted per second (8 bits per bytes).
nlscan.com Page 31 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Check No Check 【 Pro CMD : 99902120 】 Odd Check 【.
nlscan.com Page 32 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Stop Bit 1 Stop Bit 【 Pro CMD : 99902131 】 2 Stop B.
nlscan.com Page 33 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Flow Control No Flow Control 【 Pro CMD : 99902140 】.
nlscan.com Page 34 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Data Bit 8 Data Bit 【 Pro CMD : 99902150 】 8 Data B.
nlscan.com Page 35 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming 7 Data Bit 【 Pro CMD : 99902151 】 7 Data Bit, Even .
nlscan.com Page 36 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF USB Programming USB V irtual Keyboard USB V irtual Keyboard 【 Pro CMD : 99902.
nlscan.com Page 37 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF USB V irtual Keyboard Keyboard Layout No. 0 Chinese(Factory Default) 【 Pro CMD : 99902200 】 Nums Lock Nums Unlock 【 Pro CMD : 99902243 】 Character Delay The default value of Character delay time is 0ms.
nlscan.com Page 38 Data Format Introduction 1D barcodes could contain digits, letters and symbols, etc. 2D barcodes could contain more data, such as Chinese characters and other multi-byte characters.
nlscan.com Page 39 Data Format Data Format T ools Code Programming ON Code Programming OFF Pr ef ix Se qu en ce s CodeID+User Prefix+AIMID 【 Pro CMD : 99904010 】 User Prefix+CodeID+AIMID 【 Pro.
nlscan.com Page 40 Data Format Data Format T ools Code Programming ON Code Programming OFF User Prefix User Prefix is added before barcode message. For example, if the user prefix is “ AB ” and the barcode message is “ 123 ” , the Host receives “ AB123 ” .
nlscan.com Page 41 Data Format Data Format T ools Code Programming ON Code Programming OFF AIM Prefix AIM (Automatic Identification Manufactures) defines AIM prefix for many standard barcode formats. The engine will add the identifier before the barcodes.
nlscan.com Page 42 Data Format Data Format T ools Code Programming ON Code Programming OFF Code ID Prefix Besides AIM prefix, Code ID prefix can be used to denote barcode format and can be customized. The Code ID prefix MUST be one (1) or two(2) visible English letters, capital or small, only .
nlscan.com Page 43 Data Format Data Format T ools Code Programming ON Code Programming OFF Program “ AGE ” as user suffix (The hex of “ AGE ” are0x41/0x47/0x45): 1. Read “ Code Programming ON ” 2. Read “ Program User Suffix ” 3. Read “ 4,1,4,7,4,5 ” in order 4.
nlscan.com Page 44 Data Format Data Format T ools Code Programming ON Code Programming OFF T erminal Program a W indows OS general line feed and carrage returen as terminal 1. Read “ Code Programming ON ” 2. Read “ Program T erminal ” 3. Read “ Set T erminal as 0x0D,0x0A and Enable Sending ” 4.
nlscan.com Page 45 Introduction Each type of barcode has its unique attribute. W ith the programming code, the engine will adjust to the changes of these attributes. Disabling reading of the symbols which do not apply will improve reading performance.
nlscan.com Page 46 Symbols T ools Code Programming ON Code Programming OFF Code 128 Lo ad F act or y De fau lt Load Code 128 Factory Default 【 Pro CMD : 99910000 】 Enable/Disable Code 128 Enable.
nlscan.com Page 47 Symbols T ools Code Programming ON Code Programming OFF Code 128 1D bar code Message Length should not exceed 255 bytes. If Max Message Length is less than Min Message Length, it means the engine will only support barcodes of the two lengths.
nlscan.com Page 48 Symbols T ools Code Programming ON Code Programming OFF UCC/EAN-128 Lo ad F act or y De fau lt Load UCC/EAN-128 Factory Default 【 P ro C MD : 99910100 】 Enable/Disable UCC/EAN-128 When the engine can not read UCC/EAN-128, please read “ Enable UCC/EAN-128 ” and try again.
nlscan.com Page 49 Symbols T ools Code Programming ON Code Programming OFF UCC/EAN-128 1D bar code Message Length should not exceed 255 bytes. If Max Message Length is less than Min Message Length, it means the engine will only support barcodes of the two lengths.
nlscan.com Page 50 Symbols T ools Code Programming ON Code Programming OFF AIM 128 Load Factory Default Load AIM 128 Factory Default 【 P ro C MD : 99910200 】 Enable/Disable AIM 128 When the engine can not read AIM 128, please read “ Enable AIM 128 ” and try again.
nlscan.com Page 51 Symbols T ools Code Programming ON Code Programming OFF AIM 128 1D bar code Message Length should not exceed 255 bytes. If Max Message Length is less than Min Message Length, it means the engine will only support barcodes of the two lengths.
nlscan.com Page 52 Symbols T ools Code Programming ON Code Programming OFF EAN-8 Load Factory Default Load EAN-8 Factory Default 【 Pro CMD : 99910400 】 Enable/Disable EAN-8 Enable EAN-8 【 P ro.
nlscan.com Page 53 Symbols T ools Code Programming ON Code Programming OFF EAN-8 2 Di gi ts Ad de nd a C od e 2 Di gi ts Ad de nd a C od e is the one to the right of an ordinary code.
nlscan.com Page 54 Symbols T ools Code Programming ON Code Programming OFF EAN-8 EA N- 8 exp an d to EA N- 13 “ Do Not Expand to EAN-13 “ — keep original type and digits, do not expand. “ Expand to EAN-13 by Adding Leading 0s “ — expand to EAN-13 but keep code type.
nlscan.com Page 55 Symbols T ools Code Programming ON Code Programming OFF EAN-13 Lo ad F act or y De fau lt Load EAN-13 Factory Default 【 Pro CMD : 99910500 】 Di sa bl e/E na bl e EAN -1 3 Enab.
nlscan.com Page 56 Symbols T ools Code Programming ON Code Programming OFF EAN-13 Ch ec k Dig it T ransmit Check 【 Pro CMD : 99910504 】 Do Not T ransmit Check 【 Pro CMD : 99910503 】 EA N- 13 is fixed 13 digits barcode and the last digit is check digit.
nlscan.com Page 57 Symbols T ools Code Programming ON Code Programming OFF 5 Digits Addenda Code 2 Digits Addenda Code 5 Digits Addenda Code is the one to the right of an ordinary code. 2 Digits Addenda Code is the one to the right of an ordinary code.
nlscan.com Page 58 Symbols T ools Code Programming ON Code Programming OFF ISSN Load Factory Default Load ISSN Factory Default 【 Pro CMD : 99910600 】 Enable/Disable ISSN Enable ISSN 【 P ro C M.
nlscan.com Page 59 Symbols T ools Code Programming ON Code Programming OFF ISBN Load Factory Default Load ISBN Factory Default 【 Pro CMD : 99910700 】 Enable/Disable ISBN Enable ISBN 【 P ro C MD : 99910702 】 Disable ISBN 【 P ro C MD : 99910701 】 When the engine can not read ISBN, please read “ Enable ISBN ” and try again.
nlscan.com Page 60 Symbols T ools Code Programming ON Code Programming OFF ISBN ISBN Code ID Code ID Setting 【 Pro CMD : 99910705 】 Example of setting ISBN Code ID to “ p ” (0x70) 1. Read Enable Code Programming barcode. 2. Read ISSN Code ID Setting barcode.
nlscan.com Page 61 Symbols T ools Code Programming ON Code Programming OFF UPC-E Lo ad F act or y De fau lt Load UPC-E Factory Default 【 P ro C MD : 9991 1000 】 Di sa bl e/E na bl e UPC -E Enabl.
nlscan.com Page 62 Symbols T ools Code Programming ON Code Programming OFF UPC-E Check Digit UP C- E is fixed 8 digits barcode and the last digit is check digit. Check digit is a value caculated from all digits. It is used for checking if the all 8 digits are right.
nlscan.com Page 63 Symbols T ools Code Programming ON Code Programming OFF 5 Digits Addenda Code 2 Digits Addenda Code Disable 5 Digits Addenda Code 【 Pro CMD : 9991 1010 】 Enable 5 Digits Adden.
nlscan.com Page 64 Symbols T ools Code Programming ON Code Programming OFF UPC-E Tra ns mit D ef aul t “ 0 ” The first byte of UPC-E is default to “ 0 ” .
nlscan.com Page 65 Symbols T ools Code Programming ON Code Programming OFF UPC-A Load Factory Default Load UPC-A Factory Default 【 P ro C MD : 9991 1100 】 Disable/Enable UPC-A When the engine can not read UPC-A, please read “ Enable UPC-A ” and try again.
nlscan.com Page 66 Symbols T ools Code Programming ON Code Programming OFF UPC-A Check Digit UPC-A is fixed 13 digits barcode and the last digit is check digit. Check digit is a value caculated from all digits. It is used for checking if the all 13 digits are right.
nlscan.com Page 67 Symbols T ools Code Programming ON Code Programming OFF 5 Digits Addenda Code 2 Digits Addenda Code Disable 5 Digits Addenda Code 【 Pro CMD : 9991 11 10 】 Enable 5 Digits Adde.
nlscan.com Page 68 Symbols T ools Code Programming ON Code Programming OFF Interleaved 2 of 5 Load Factory Default Load Interleaved 2 of 5 Factory Default 【 Pro CMD : 9991 1200 】 Disable/Enable .
nlscan.com Page 69 Symbols T ools Code Programming ON Code Programming OFF Interleaved 2 of 5 Check Digit Interleaved 2 of 5 may include Check Digit (not compulsory) following its barcode messages. If included, it could be the last digit. It verifies the barcode message.
nlscan.com Page 70 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Interleaved 2 of 5. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 71 Symbols T ools Code Programming ON Code Programming OFF ITF-6 ITF-6 is a fixed length 6 bytes Interleaved 2 of 5 barcode with check digit.
nlscan.com Page 72 Symbols T ools Code Programming ON Code Programming OFF ITF-14 ITF-14 is a fixed length of 14 bytes Interleaved 2 of 5 barcode with Check digit. By factory default, it is disabled. Wh en e na bl ed , IT F- 14 p re ce de s 14 -b yt e In te rl ea ve d 2 of 5 b ar co de .
nlscan.com Page 73 Symbols T ools Code Programming ON Code Programming OFF Deutshe14 Load Factory Default Load Deutshe14 Factory Default Deutshe14 Factory Default Factory Default 【 Pro CMD : 9991 .
nlscan.com Page 74 Symbols T ools Code Programming ON Code Programming OFF Deutshe12 Load Factory Default Load Deutshe12 Factory Default Deutshe12 Factory Default Factory Default 【 Pro CMD : 9991 1600 】 Disable/Enable Deutshe12 When the engine can not read Deutshe12, please read “ Enable Deutshe12 ” and try again.
nlscan.com Page 75 Symbols T ools Code Programming ON Code Programming OFF COOP25 ( Japanese Matrix 25 ) Load Factory Default Load COOP25 Factory Default 【 P ro C MD : 9991 1700 】 Enable/ Disable COOP25 When the engine can not read COOP25, please read “ Enable COOP25 ” and try again.
nlscan.com Page 76 Symbols T ools Code Programming ON Code Programming OFF COOP25 ( Japanese Matrix 25 ) Check Digit COOP25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It verifies the barcode message.
nlscan.com Page 77 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of COOP25. The engine will send an error beep, if the decoded data length does not match the valid length. COOP25 Message Length is defined by “ Min.
nlscan.com Page 78 Symbols T ools Code Programming ON Code Programming OFF Matrix 25( European Matrix 25) Lo ad F act or y De fau lt Load Matrix 25 Factory Default 【 P ro C MD : 99912000 】 Enable/ Disable Matrix 25 When the engine can not read Matrix 25, please read “ Enable Matrix 25 ” and try again.
nlscan.com Page 79 Symbols T ools Code Programming ON Code Programming OFF Matrix 25( European Matrix 25) Check Digit Matrix 25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It verifies the barcode message.
nlscan.com Page 80 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Matrix 25. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 81 Symbols T ools Code Programming ON Code Programming OFF Industrial 25 Load Factory Default Load Industrial 25 Factory Default 【 P ro C MD : 99912100 】 Enable/ Disable Industrial 25 When the engine can not read Industrial 25, please read “ Enable Industrial 25 ” and try again.
nlscan.com Page 82 Symbols T ools Code Programming ON Code Programming OFF Industrial 25 Check Digit Industrial 25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It verifies the barcode message.
nlscan.com Page 83 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Industrial 25. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 84 Symbols T ools Code Programming ON Code Programming OFF Standard 25 Load Factory Default Load Standard 25 Factory Default 【 P ro C MD : 99912200 】 Enable/ Disable Standard 25 When the engine can not read Standard 25, please read “ Enable Standard 25 ” and try again.
nlscan.com Page 85 Symbols T ools Code Programming ON Code Programming OFF Standard 25 Check Digit Standard 25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It verifies the barcode message.
nlscan.com Page 86 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Standard 25. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 87 Symbols T ools Code Programming ON Code Programming OFF Code 39 Load Factory Default Load Code 39 Factory Default 【 P ro C MD : 99912400 】 Enable/Disable Code 39 When the engi.
nlscan.com Page 88 Symbols T ools Code Programming ON Code Programming OFF Code 39 When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to error beep.
nlscan.com Page 89 Symbols T ools Code Programming ON Code Programming OFF Code 39 T ransmit Start & Stop Character Code 39 has one "*" before and another after digits as Start & Stop Character . T ransmission of “ * ” can be selected.
nlscan.com Page 90 Symbols T ools Code Programming ON Code Programming OFF Code 39 Select Message Length Code 39 Message Length is defined by “ Min. Message Length ” and “ Max. Message Length “ .It is used to program the valid reading length of Code 39.
nlscan.com Page 91 Symbols T ools Code Programming ON Code Programming OFF Codabar Load Factory Default Load Codabar Factory Default 【 Pro CMD : 99912500 】 Enable/Disable Codabar When the engine can not read Codabar , please read “ Enable Codabar ” and try again.
nlscan.com Page 92 Symbols T ools Code Programming ON Code Programming OFF Codabar When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to error beep.
nlscan.com Page 93 Symbols T ools Code Programming ON Code Programming OFF Codabar T ransmit Start & Stop Character Do Not T ransmit Both Start & Stop Character 【 Pro CMD : 99912506 】 Us.
nlscan.com Page 94 Symbols T ools Code Programming ON Code Programming OFF Codabar Select Message Length Codabar Message Length is defined by “ Min. Message Length ” and “ Max. Message Length “ .It is used to program the valid reading length of Codabar .
nlscan.com Page 95 Symbols T ools Code Programming ON Code Programming OFF Code 93 Load Factory Default Load Code 93 Factory Default 【 P ro C MD : 99912600 】 Enable /Disable Code 93 When the engine can not read Code 93, please read “ Enable Code 93 ” and try again.
nlscan.com Page 96 Symbols T ools Code Programming ON Code Programming OFF Code 93 When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to error beep.
nlscan.com Page 97 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Code 93. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 98 Symbols T ools Code Programming ON Code Programming OFF Code 1 1 Load Factory Default Load Code 1 1 Factory Default 【 P ro C MD : 99912700 】 Enable/ Disable Code 1 1 When the engine can not read Code 1 1, please read “ Enable Code 11 ” and try again.
nlscan.com Page 99 Symbols T ools Code Programming ON Code Programming OFF Code 1 1 Check Digit Code 1 1 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last one or two digits. It verifies the barcode message.
nlscan.com Page 100 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Code 1 1. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 101 Symbols T ools Code Programming ON Code Programming OFF Plessey Load Factory Default Load Plessey Factory Default 【 P ro C MD : 99913000 】 Enable/ Disable Plessey When the engine can not read Plessey , please read “ Enable Plessey ” and try again.
nlscan.com Page 102 Symbols T ools Code Programming ON Code Programming OFF Plessey Check Digit Plessey may include Check Digits (not compulsory) following its barcode messages. If included, they are the last two digit. They verifie the barcode message.
nlscan.com Page 103 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Plessey . The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 104 Symbols T ools Code Programming ON Code Programming OFF MSI-Plessey Load Factory Default Load MSI-Plessey Factory Default 【 P ro C MD : 99913100 】 Enable/ Disable MSI-Plessey When the engine can not read MSI-Plessey , please read “ Enable MSI-Plessey ” and try again.
nlscan.com Page 105 Symbols T ools Code Programming ON Code Programming OFF MSI-Plessey Check Digit MSI-Plessey may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last one or two digits. It verifies the barcode message.
nlscan.com Page 106 Symbols T ools Code Programming ON Code Programming OFF Select Message Length MSI-Plessey Message Length is defined by “ Min. Message Length ” and “ Max. Message Length ” .It is used to program the valid reading length of MSI-Plessey .
nlscan.com Page 107 Symbols T ools Code Programming ON Code Programming OFF GS1 Databar Load Factory Default Load GS1 Databar Factory Default 【 P ro C MD : 99913200 】 Enable/ Disable GS1 Databar When the engine can not read GS1 Databar, please read “ Enable GS1 Databar ” and try again.
nlscan.com Page 108 Appendix Factory Default List Parameters Factory Default Remark General Programming Code Programming On Send Pro Code V alue Off W orking Mode Sensor Mode Reading a Barcode T ime Length 3s Range : 0-15s , 0 is infinite time. Interval Length 1s Range : 0-7.
nlscan.com Page 109 Appendix Factory Default List Parameters Factory Default Remark Symbol Code 128 Enable On Max Message Length 255 Min Message Length 1 UCC/EAN-128 Enable On Max Message Length 255 M.
nlscan.com Page 1 10 Appendix Factory Default List ISSN Enable Off ISBN Enable Off Use 10 Digits Off UPC-E Enable On Send Check Digit On Enable 2 Digits Addenda Code Off Enable 5 Digits Addenda Code O.
nlscan.com Page 1 11 Appendix Factory Default List Deutsche 14 Enable Off Send Check Digit On Deutsche 12 Enable Off Send Check Digit On COOP 25(Japanese Matrix 25) Enable Off Check Off Send Check Dig.
nlscan.com Page 1 12 Appendix Factory Default List Support Full ASCII On Max Message Length 255 Min Message Length 4 No less than 4 (including St ar t & St op C har ac te r) Codabar Enable On Chec.
nlscan.com Page 1 13 Appendix Factory Default List Max Message Length 255 Min Message Length 4 No less than 1 MSI-Plessey Enable Off Send Check Digit Off No Check On 1 Di gi t, MOD10 Check Off 2 Di gi.
nlscan.com Page 1 14 Appendix AIM ID List Symbol AIM ID Possible AIM ID Modifiers(m) Code 128 ]C 0 UCC/EAN-128 ]C 1 AIM 128 ]C 2 IS BT 12 8 ]C 4 EAN-8 ]E 4 EAN-13 ]E 0 EAN-13 with Addon ]E 3 ISSN ]X 0.
nlscan.com Page 1 15 Appendix Code ID List Symbol Code ID Code 128 j UCC/EAN-128 u AIM 128 f IS BT 12 8 t EAN-8 g EAN-13 d ISSN n ISBN B UPC-E h UPC-A c Interleaved 2 of 5 e ITF-6 r ITF-14 q Deutsche .
nlscan.com Page 1 16 Appendix Appendix T ools Code Programming ON Code Programming OFF Digit Code It is must to read save after reading digit code. 0 【 Pro CMD :99900000】 1 【 Pro CMD :999000.
nlscan.com Page 1 17 Appendix Digit Code 8 【 Pro CMD :99900010】 9 【 Pro CMD :99900011】 A 【 Pro CMD :99900012】 B 【 Pro CMD :99900013】 C 【 Pro CMD :99900014】 D 【 Pro CMD .
nlscan.com Page 1 18 Appendix Appendix T ools Code Programming ON Code Programming OFF Save and Abort In order to save the received data “ Save ” has to be read after data transition completed. If error occurs when reading data, the wrong data can be deleted and the setting up can be done again.
nlscan.com Page 1 19 Revisions V ersion Data Source Description Date Approved Pre-release version 20090826.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Newland FM100 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Newland FM100 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Newland FM100 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Newland FM100 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Newland FM100, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Newland FM100.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Newland FM100. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Newland FM100 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.