Manuale d’uso / di manutenzione del prodotto AS-8020CL del fabbricante Argox
Vai alla pagina of 145
NOTICE: This equipment has been tested and compli ed with the limits for a Class a digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against ha rmful interface when the equipment is o perated under a commercial environment.
Using the ArgoxScan AS -8020CL The Argo xScan can auto matically scan barcode at a di stance . Simply aim and pull the trigger . Code scanning i s performed along the center of the light bar emit ted from the reading window . This bar must cover the entire code (see “How to Scan” in page 9).
.
.
CONTENT S Chapter 1 Introduct ion Installation……… ………………… ………………… 1 How T o Scan……………………… ………………… 13 Tr oubleshooting……… …….
Code 39 ……………… …………… ………………… 75 Interleaved 2 of 5 ……… ………… ………………… 79 Industrial 2 of 5 …… ………………………… ……….
1 Inst allation The AS -8020CL Wireless Imager is ea sy to install and use. Please see the follow ing figure sh owing the steps to perfor m the installation. * Note : T urn off the hos t computer before in stallation. 1. Connect the interface (I/F) cable t o the cradle.
2 Connecting A S-8020CL to PC w ith USB Dongle AS-8020CL is allow ed to connect w ith PC via USB dongle . 1. .Scan the following barcodes to set scanner to Bluetooth connection mode, w ith PIN code as.
3 Within the promp t, click “Add”. 3. Check the option, “My device is set up and ready to be found” and click” Nex t”..
4 4. Select “AS-8020CL” among th e Bluetooth devices found; click “Nex t”. 5. S elect “Don’t use a passkey” and click “Nex t”. The Bluetooth connection will start to install the Blue.
5 6. As it p rompts, “ Completing the Blue tooth Dev ice W izard”, find which COM ports is assigne d. The follow ing example lists COM 23 as the Outg oing port , and COM2 4 as Incoming port; your actual COM ports will depend on what’s assigned on your PC.
6 7. Open HyperTer minal. Set COM1’s Baud Rate as 9600 to communicate with AS-8020CL (whose default baud rate is 9600):.
7 8. Select COM23 (depending on your Outgoing COM port) to connect. Click “O K”. 9. Click on “Dial”..
8 10. The system w ill show a m essag e on T askbar asking to click on the Bluetooth sign on t askbar . After clicking on it, the wizard will prompt as below; enter 0000 (AS-8020CL default PIN code) w ithin the Pas skey fie ld; click “Nex t”.
9 Connecting A S-8020CL to Smart De vice v ia HID P rotocol without A Cradle AS-8020CL B luetooth HID pr ovide s the ability to c onnect other Bluetooth devices, for example smart phones, t ablet PCs, iPod, iPhone, iPad,… which require HID protocol to pair with.
10 6. Simply click the “Note s” in desktop of Apple device and create a “New Note”. T ap on the New No te and see the cursor sho wed on the screen. Use your A rgox Cordless Scanner to scan a barcode and the data w ill show on the Note. Note: Apple iOS devices will allow only one inp ut device working at the same time.
11 6. Click the found devi ce and you will hear three beeps af ter cert ain connecting time. The status will be changed to “C onnected to i nput device”. Now yo ur Argox Cordless Scanner successfully connects w ith your Android device. 7. Simply click the “M ini Diary” in des ktop of Android device.
12 HID re-connect duration from scan ner to PC (1AC01~1AC09 – 10 sec ~ 90sec)..
13 How to Scan 1. The imager must be pointed at sligh t angle to the barcode so that the light reflected off the bar code can be seen by the image r . Do not hold the imager perpendicular to the bar code. 2. The scan line must cross the entire barcode.
14 T rouble shooting If the imager can not operate prop erly , t he following checks should be performed : 1. The cradle uses an ex ternal pow er supply and the extern al power supply has failed, t he imager will not operate. Change the power supply with a known goo d power supply and rese t the imager .
15 3. V erify the interface cable is secure ly connected to the cradle. 4. Check that the bar codes are of suf f icient quality to be recognized by the imag er . Wrinkled, smudged, or torn labels will cause the imager to not read at all. Scan a known good labe l to check the i mager’s read operation.
16 Wireless Connection Linking the image r wit h the cradle Follow these instru ctions to link the two devices: 1. Connect power to the cradle. The rad io LED (marked with a light symbol) will blink ambe r and the cradle w ill beep.
17 Unlinking There are three w ays to unlink an imager from a cradle: Force imager to discon nect and sleep 1. Scan the “Force imager to disconnec t and sleep” barcode – Reading the unlink barcode abo ve while the imager is in range of the cradle w ill break the link between the two devices and allo w another imager to link to the cradle.
18 4. Push the “Reset ” button on the bottom of crad le – If the cradle is linked w ith an imager a nd in range, pushing the “Reset” button (for ab out 2 seconds) on the bottom of cradle will drop the link betwee n the devices.
19 Battery Charging The imager contain s a 1000 mAh Lithiu m-Ion rechargeable battery . A full charged ba ttery will pr ovide up to 55,000 s cans over a 15 hours period.
20 How t o Change the Batt ery In case the containe d battery in side the imager needs to be replaced, please follow the procedu res below: 1. Loosen the screw at the bottom of the i mager . 2. T ake of f the batter y cover out of the imager . 5. Use a new battery pack and replace the used one.
21 Note : DO NOT touch the PCB A inside the imager w hen replacing the batter y . Improper operation may damage the imager . 6. Place the new ba ttery into the battery containe r . 7. Connect the bat tery cable connector to the main boa rd. 8. Put the battery cover back to the imager handle .
22 Wireless Features The AS -8020CL Wireless model includes an i mager and a cradle. When the i mager and cradl e are linked toge ther , the imager will read and decode barco des and transmit them via a Wireless radio to the cradle. The cradle w ill then trans mit the barcode dat a to the hos t computer over the host cable.
23 Auto Update When this feature i s enabled, an imager and its linked cradle can automatically en sure they st ay in sync with rega rd to firmware and/or configuration. This is acco mplished by the linked i mager and cradle c omparin g firmware version number and configuration file check sum.
24 Enable firmware a uto up date on ly – A llows only firmware upda ting. Disable auto up date – No automatic updates w ill be performed..
25 Deep Sleep M ode The WIRELESS i mager can be pl aced into Deep Sleep Mode after thi s progra mmed duration (sin ce the units ’ last scanning activity).
26 Wireless Connectiv ity The AS -8020CL can be linked to any Bluetooth (BT) enab led device which can ac cept such a connection with o ther devices. T o implement this fea ture, user should set the imager to “Crad le/Dongle connection auto detection” fir st.
27 Wireless Connectiv ity (co ntinued) User is also allow ed to set any four - to six-character PIN code assigned to the target Bluetooth device using the setting procedures below : ST A TE CODE Cradle/Dongle connection auto detection Program Begin PIN setting PIN no.
28 Inquiry Beep Con trol When the cradle is no t linked to an imager , the Radio LED will blink amber and the cradle w ill beep. This beep can be disabled or reconfigured to sound for differen t durations by using the follow ing programming b arcodes.
29 Inquiry beep every 50 seconds Inquiry beep every 60 seconds Inquiry beep every 70 seconds.
30 Cradle Beep Loud ness C ontrol The beep loudness o f cradle can b e defined with the following levels. Cradle beep off Level 1 Level 2 Level 3 (Default) Level 4 Level 5.
31 Level 6 Level 7.
32 Additional Featu res Here list three additiona l features o f AS-8020CL w ireless imager for the conv enience of use to users. Download firmware from the cra dle Download configurat ion p a.
33 Default setting For each barcode shown as below: Code T ype Read Enable Checksum V erification Enable Checksum T ransmission Enable Code ID UPC-A A UPC-E E EAN-13 F EAN-8 FF Code-39 Interleaved 2 o.
34 Specification ArgoScan AS-8020CL S pecificat ion Model A S-8020CL Operational Light Source 630 nm Vi sible Red LED Optical System 2048 pix el CCD (Charge- coupled device) Depth of Scan Field 0~270mm (CODE 39, PSC=90%, 20mil) 0~180mm for 13 mil 0~60mm for 5mil 5mm~50mm for 4 mil Scan S peed 300 scans/sec Resolution 0.
35 Depth-head 44 mm Weight Less than 200g (w ith a battery) Case material ABS (over molded a t contact points) Cushion material Double injection Cradle interface RS232, Keyboar d wedge , USB Electrica.
36 Current – Sleep (Imager) 2 mA Light Level Up to 45000 Lux Shock (Imager) 1.5m drop onto concrete Shock (Cradle) 90cm drop on to concrete Contaminant s Seals to resist airbor ne parti culate conta.
37 Indications of A S-802 0CL Imager: S ta tus Green LED Red LED Orange LED Beeper LED Link established Blink once A special beep Hardware fail Flash Program downlo ad Flash Program checksum fail Flash Data transmitting ON High freq. Beep for 300msec Data trans.
38 Cradle: S ta tus Green LED Red LED Orange LED Beeper RF status LED Inquiry Blink Beeps once a second Connecting Blink Link established ON Hardware fail Flash Data receiving from the scanner ON for 0.
39 Programming the A S -8020CL T o program the AS-8020CL, you must scan a series of programming barcode in the corre ct order . Fold out the back cover of this manual . Y ou will see a ta ble of alphanu meric barcodes, wh ich are used to progr am the various op tions presented.
40 Option Bar Code Option Alphanumeric Entry Interface selection Keyboard Wedge RS-232 Wand e mulation USB Keyboard/RS-23 2 Auto detection Reserved 00 01 02 03 04 05 Prog ram Exit Program Barcode Opti.
41 Exit Interface Selection This cradle comes in one m odel a nd support s interface s such as keyboa rd wedg e, RS232 serial wedge, and USB interface . In most of the cases , simply select ing an appropr iate cable with a device code w ill work for a sp ecific interface.
42 Exit Keyboard wedge As a keyboard interfa ce, the cradl e support s most of the popular PCs and IBM ter minals. T he inst allation of the w edge is a fairly simple pro cess without any changes of sof tware or hardware . Keyboard T y pe: Select keyboard typ e connector of your host computer .
43 Keyboard wedge Keyboard Lay out: The selecting of keyboar d layout supports many country language s other than U SA keyboard layout. First you need to confirm cou ntry language that you desire.
44 Exit Keyboard layou t USA Belgium Danish France Germany Italian Portuguese S pan ish Swedish Switzerland UK Latin Am erican Japanese 00 01 02 03 04 05 06 07 08 09 10 1 1 12 Keyboard speed 0-8 0 : h.
45 Keyboard wedge Cap s Lock: By select ing Caps lock”ON” or Caps lock”OFF” , imager can get Cap s Lock status. Power-on simulat ion: All of the P Cs check the keyb oard status durin g pow er-on selftest. It i s recommende d to Enable function if you are w orking without key board insta llation.
46 Exit Option Bar Code Optio n Alphanumeric Entry Caps lock Caps lock”ON” Caps lock”OF F” 00 01 Power-o n simulation Disable Enable 00 01 Inter-character delay 00-99 (msec) 00-99 02 Block tra.
47 RS-232 CTS: Clear T o Send (Hardw are Signal) RTS: Request T o Send (Hard ware Signal) Xon: T ran smit On (A SCII Code 1 1 16 ) Xoff: Tr ansmit Of f (ASCII Code13 16 ) Flow control : None- The communi cation only u ses Tx D and Rx D signals without regard for any hardw are or softw are handshaking protocol.
48 Exit Option Bar Code Optio n Alphanumeric Entry Flow control None RTS/CTS Xon/Xof f ACK/NAK RTS/CTS bra cket mode 00 01 02 03 04 Inter-character delay 00-99 (msec) 00-99 00 Block transmission delay.
49 Exit Option Bar Code Optio n Alphanumeric Entry Baud rate 300 BPS 600 BPS 1200 BPS 2400 BPS 4800 BPS 9600 BPS 19200 BPS 38400 BPS 00 01 02 03 04 05 06 07 Parity None Odd Even 00 01 02 Data bit 8 bi.
50.
51 Pin A ssignment s 10-pin A S Series 10-pin RJ-45 Connector Pin RS-232 Keyboard 1 I/F I/F 2 NA NC 3 TXD NC 4 NC CLK / PC 5 GND DA T A / PC 6 CTS DA T A / KB 7 RXD NC 8 RTS CLK / KB 9 GND GND 10 NC G.
52 Keyboard Wedge PS/2 Con nector (T o Host Side): Pin Mini-D IN 6P Male Mini-DIN 6P Female 1 DA T A / PC DA T A / KB 2 NC NC 3 GND GND 4 VCC (+5V) NA 5 CLK / PC CLK / KB 6 NC NC RS-232 DB-9F Connect .
53 Scan Scanning mode: Good-read off- Th e trigger button mus t be pressed to activate scanning. The light source of image r stop s scanning when there is a successful reading or no code is decode d after the Stand -by duration elapse d. Moment ary- The trigger button act s as a s witch.
54 Exit Option Bar Code Optio n Alphanumeric Entry Scanning mode Good-read of f Momentary Alternate Ti meout of f Continue T est only 00 01 02 03 04 05 S tand- by duration 01-99 (second) 00-99 06 Doub.
55 Scan Global min./max . code length : These are to de fine the min/ max readable code le ngth of all symbolog ies. Code leng th less than mi n. code length or more than max. code length w ill not be read. In popular , you can set the same value for both min.
56 Exit Option Bar Code Optio n Alphanumeric Entry Global min. code leng th 00-99 00-99 04 Global max. code leng th 00-99 00-99 99 Inverted image scan Disable Enable 00 01 Program.
57 Indication Power on alert: Af ter powe r-on the cradle it will gene rate an alert signal to indicate a successfu l self-test. LED indication: After ea ch successful reading, the LED above the imager w ill light up to in dicate a good barcode reading.
58 Exit Option Bar Code Optio n Alphanumeric Entry Power on alert Disable Enable 00 01 LED indication Disable Enable 00 01 Beeper indication Disable Enable 00 01 Beep loudness 00-07 (00 - off) 00-07 07 Beep tone freq.
59 UPCA Format Leading Zero Data Digit s (1 1 Digits) Check Digit Read: Enable or disable the read f unction. Check-sum trans mission: By set ting Enable , checks sum will be transmitted. T runcate leading/ending: The le ading or ending digit s of barcode dat a characters can b e trun cated wh en these value s are set to non-z ero.
60 Exit Option Bar Code Optio n Alphanumeric Entry Read Disable Enable 00 01 Check-sum transmis sion Disable Enable 00 01 Tr uncate leading 0-15 0 0-15 00 Tr uncate ending 0-15 00- 15 00 Code ID setti.
61 UPCA Insertion group number selectio n: The imager of fers max . two insertion group s for one symbology . By setting one or two digits to indi cate which insertion group you want to insert. Y ou may refer to Character insert ion. The function is to insert specific characters a s a group into trans mitted data of selected symbologie s.
62 Exit Option Bar Code Optio n Alphanumeric Entry Insert group nu mber selection 00-44 00-44 00 Supplement digit s None 2 digits 5 digits 2,5 digits UCC/EAN 128 2, UCC/EAN 128 5, UCC/EAN 128 All 00 0.
63 UPCE Read: Format Leading Zero Data Digit s (6 Digits) Check Digits Check-sum trans mission: By set ting Enable , checks sum will be transmitted. T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code ID setting : Refer to Code ID setting of UPCA.
64 Exit Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 00-ffH < E >.
65 UPCE Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A. Supplement digit s : Format Leading Zero Data Digit s (6 Digits) Check Digit Supplement Digit s 2 or 5 or UCC/EAN 128 Expans ion: The ex p ansion function is used only for UPCE and EAN- 8 code re ading.
66 Exit Supplement digit s None 2 digits 5 digits 2,5 digits UCC/EAN 128 2, UCC/EAN 128 5, UCC/EAN 128 All 00 01 02 03 04 05 06 07 Tr uncation/Exp ansion None Tr uncate leading zero Exp and to E AN13 .
67 EAN-13 Read: Format Data Digit s (12 Digit s) Check Digit s Check-sum trans mission: By set ting Enable , checks sum will be transmitted. T runcate leading/ending: Refer to T run cate leading/ending of UPCA. T runcate leading zero: Refer to T runcation / Exp ansion of UPCA.
68 Exit Tr uncate ending 0-15 00-15 00.
69 EAN-13 Code ID setting: R efer to p age 5 7 th I nsertion gr oup nu mber selection of UPCA. Insertion gro up numbe r selection: R efer to I nsertion gr oup selection of UPCA.
70 Exit Supplement digit s None 2 digits 5 digits 2,5 digits UCC/EAN 128 2, UCC/EAN 128 5, UCC/EAN 128 All 00 01 02 03 04 05 06 07 ISBN/ISSN conversion Disable Enable 00 01 ISBN ID setting 00-ffH ASCI.
71 EAN-8 Read: Format Data Digit s (7 Digits) Check Digits Check-sum trans mission: By set ting Enable , checks sum will be transmitted. T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code ID setting : Refer to Code ID setting of UPCA.
72 Exit Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 00-ffH, 00- ffH < FF > Insert group nu mber selection 00-44 00-44 00.
73 EAN-8 Supplement digit s : Format Data Digit s (7 Digits) Check Digits Supplement Digit s 2 or 5 or UCC/EAN 128 T runcation / Expans ion: Refer to T runcate Leading zero of UPCE.
74 Exit Exp ansion Disable Enable 00 01.
75 Code 39 Read: Format S tart “ ” Data Digit s ( V ariable) Checksum (Optional) End “ ” Check-sum verificat ion: The che cksum of Code- 39 is optional and made as the sum mo dule 43 of the nu merical value of the data digit s. Check-sum trans mission: By set ting Enable , checksum will be transmitted.
76 Exit Check-sum verification Disable Enable 00 01 Check-sum transmission Disable Enable 00 01 Max. code length 00-64 00-64 00 Min. code length 00-64 00-64 00 Tr uncate leading 0-15 00-15 00 Tr uncat.
77 Code 39 Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A. Format: The Full ASCII Code-39 is an enhan ced set of Code-39 that is the dat a w ith total o f 128 characters to represent Full ASCII code.
78 Exit Format S tanda rd Full ASCII 00 01 Append Disable Enable 00 01 S tart /end transmission Disable Enable 00 01.
79 Interleaved 2 of 5 Read: Format Data Digit s (V ariable) Checksum (Optional) Check-sum ver ification: The checksum is made a s the su m module 10 of the nu merical value s of all data digits . Check-sum trans mission: By set ting Enable , checksum will be transmitted.
80 Exit Check-sum transmission Disable Enable 00 01 Max. code leading 00-64 00-64 00 Min. code leading 00-64 00-64 00 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-.
81 Industrial 2 of 5 Read: Format Data Digit s (V ariable) Checksum (Optional) Max./Min. code length : Refer to Max./Min. code len gth of Code-39. T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code Id setting: Re fer to Code ID se tting of UPCA.
82 Exi t Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 00-ffH < i > Insert group nu mber selection 00-44 00-44 00.
83 Matrix 2 of 5 Eur Read: Format Data Digit s (V ariable) Checksum (Optional) Checksum V erification: The che cksum is made as the sum module 10 of the nu merical value s of all data digits . Checksum T ransmission: By setting Enable , che cksum w ill be transmitted.
84 Exit Checksum Tr ansmission Disable Enable 00 01 Max. code length 00-64 00-64 00 Min. code length 00-64 00-64 00 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ff.
85 Codabar Read: Format Checksum V erification: The che cksum is made as the sum module 16 of the nu merical value s of all data digits . Checksum T ransmission: By setting Enable , che cksum w ill be transmitted. Max./Min. code length : Refer to Max.
86 Exit Checksum Tr ansmission Disable Enable 00 01 Max. code length 00-64 00-64 00 Min. code length 00-64 00-64 00 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ff.
87 Exit Codabar Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A. St art/End ty pe: The Codabar has four pairs of S tart/End pattern; you may select one p air to match your applicat ion. St art/End T ransmission: Refer to S tart/End T ransmission of Code 39.
88 Exit Code-128 Read: Format Data Digit s (V ariable) Checksum (Optional) Checksum V erification: The che cksum is made as the sum module 103 of all dat a digit s.
89 Code-128 Max./Min. code length : Refer to Max./Min. code len gth of Code-39. T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code ID setting : Refer to Code ID setting of UPCA. Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A.
90 Exit Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 00-ffH < # > Insert group nu mber selection 00-44 00-44 00 Format S tanda rd UCC/EAN-128 .
91 Exit Code-128 ISBT enable: This fea ture is commonly used in a blood bank for identification. ISBT concatenatio n timeout: This feature i s to setup the timeout duration of ISBT con catenation. Field sep arator code : This feature is only used for UCC/EAN-128 format .
92 Exit Code-93 Read: Format Data Digit s (V ariable) Checksum1 (Optional) Checksum2 (Optional) Checksum V erification: The che cksum is made as the sum module 47 of the nu merical value s of all data digits . Checksum T ransmission: By set ting Enable , checksum will be transmitted.
93 Code-93 Max./Min. code length : Refer to Max./Min. code len gth of Code-39. T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code Id setting: Re fer to Code ID se tting of UPCA. Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A.
94 Exit Code ID setting 00-ffH ASCII code 00-ffH < & > Insert group nu mber selection 00-44 00-44 00.
95 Code-1 1 Read: Format Data Digit s (V ariable) Checksum1 (Optional) Checksum2 (Optional) Checksum V erification: The che cksum is presented a s the sum module 1 1 of all data digit s. Checksum T ransmission: By set ting Enable , checksum1 and checksum2 w ill be transmitted upon your selected checksum verification method.
96 Exit Checksum Tr ansmission Disable Enable 00 01 Max. code length 00-64 00-64 00 Min. code length 00-64 00-64 00 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ff.
97 MSI/plesse y Read: Format Data Digit s (V ariable) Checksum1 (Optional) Checksum2 (Optional) Checksum V erification: The M SI/Plessey has one or two optional checksum dig its. The checksum is presen ted 3 kinds of method Mod10 , Mod10/10 and Mod 1 1/10 .
98 Exit Checksum Tr ansmission Disable Enable 00 01 Max. code length 00-64 00-64 00 Min. code length 00-64 00-64 00 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ff.
99 UK/plessey Read: Format Data Digit s (V ariable) Checksum1+2 (Optional) Checksum V erification: The UK /Plessey ha s one or two optional checksum dig its. The che cksum1 and chec ksum2 will be calculated as the sum modu le 10 or 1 1 of the data digits.
100 Exit Checksum Tr ansmission Disable Enable 00 01 Max. code length 00-64 00-64 00 Min. code length 00-64 00-64 00 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-f.
101 T elepen Read: IA T A (International Air Tr ansport Association). Checksum V erification: The che cksum is presented a s the sum module 10 or 1 1 of the data d igits. Checksum T ransmission: By setting Enable , che cksum w ill be transmitted. Max.
102 Exit Max. code length 00-64 00-64 00 Min. code length 00-64 00-64 00 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 00-ffH < S > Insert grou.
103 St andard 2 of 5 Read: Format Data Digit s (V ariable) Checksum1 (Optional) Check-sum ver ification: The checksum is made a s the su m module 10 of the nu merical value s of all data digits . Check-sum trans mission: By set ting Enable , checksum will be transmitted.
104 Exit Check-sum transmission Disable Enable 00 01 Max. code length 00-64 00-64 00 Min. code length 00-64 00-64 00 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-f.
105 China Post Read: Format Data Digit s (V ariable) Checksum1 (Optional) Max./Min. code length : Refer to Max./Min. code len gth of Code-39. T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code Id setting: Re fer to Code ID se tting of UPCA.
106 Exit Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 00-ffH < t > Insert group nu mber selection 00-44 01-44 00.
107 It alian Pharmacode (Code 32) Read: Format Data Digit s (V ariable) Checksum1 (Optional) Max./Min. code length : Refer to Max./Min. code len gth of Code-39. T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code Id setting: Re fer to Code ID se tting of UPCA.
108 Exit Min. code length 00-64 00-64 09 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 01-ffH < p > Insert group nu mber selection 00-44 00-44 .
109 Code-16K T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code ID setting : Refer to Code ID setting of UPCA. Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A.
110 Exit Insert group nu mber selection 00-44 00-ffH 00-44 00.
1 1 1 PDF-417 T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code ID setting : Refer to Code ID setting of UPCA. Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A.
112 Exit Option Bar Code Optio n A lphanumeric Entry Read Disable Enable 00 01 Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 00-ffH < P > Inser.
113 EAN UCC Composite For the coupon ex tended code ap plication. Coupon ex tended code is a supplementary barcode th at is pr inted to the right of the UPC/EAN in UCC /EAN-128 sy mbology .
114 Exit UCC / EAN128 emulation Disable Enable 00 01.
115 Dat aBar (RSS-14) Read: Format Data Digit s (V ariable) Checksum1 (Optional) T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code ID setting : Refer to Code ID setting of UPCA. Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A.
116 Exit Tr uncate leading 0-15 00-15 00 Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 00-ffH < R4 > Insert group nu mber selection 00-44 00-44 00 UCC/EAN128 emulation Disable.
117 Dat aBar (RSS-Limited) Read: Format Data Digit s (V ariable) Checksum1 (Optional) T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code ID setting : Refer to Code ID setting of UPCA. Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A.
118 Exit Code ID setting 00-ffH ASCII code 00-ffH < RL > Insert group nu mber selection 00-44 00-44 00 UCC/EAN128 emulation Disable Enable 00 01.
119 Dat aBar (RSS-Exp anded) Read: Format Data Digit s (V ariable) Checksum1 (Optional) T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code ID setting : Refer to Code ID setting of UPCA. Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A.
120 Exit Tr uncate ending 0-15 00-15 00 Code ID setting 00-ffH ASCII code 00-ffH < RX > Insert group nu mber selection 00-44 00-44 00 UCC/EAN128 emulation Disable Enable 00 01.
121 Micro-PDF T runcate leading/ending: Refer to T run cate leading/ending of UPCA. Code ID setting : Refer to Code ID setting of UPCA. Insertion group number selectio n: Refer to pa ge 57 th Insertion group nu mber selection of UPC A.
122 Exit Insert group nu mber selection 00-44 00-44 00 Escape sequence transmit None GLI protocol ECI protocol 00 01 02.
123 String setting / T ransmiss ion (Prefix / Suffix) Prefix / Suffix chara cters setting : Characters defined a s prefix or suf fix character s w ill be trans mitted i mmediately w ith the scanned data for all sy mbologies. Up to 22 ASCII characters can be defined as Prefix or Suffix.
124 Exit Option Bar Code Optio n A lphanumeric Entry Prefix characters setting None 1-22 characters 00 00-ffH ASCII code Suffix characters setting None 1-22 characters 0D 00-ffH ASCII code Program.
125 String setting / T ransmiss ion (Preamble/Postamble ) Preamble/ Post amble characters: Prea mble or Posta mble characters will be append ed to the dat a automatically for all symbologies. How ever , the transmission will not ac tivate unless Preamble / Post amble trans mission is enabled.
126 Exit Option Bar Code Optio n A lphanumeric Entry Preamble character s setting 1-22 characters “ PREAMBLE ” 00-ffH ASCII code Preamble transmission Disable Enable 00 01 Posta mble characters se.
127 String setting / T ransmiss ion (Insert Group Characters) Insert G1/G2/G3 /G4 character se tting: The imager supports inser ting two groups w ith each group 22 chara cters into transmitted dat a of sele cted symbologie s. The two group s can be inserted into scanned data of the selected symbologies or po sitioned at leadi ng / ending of da ta.
128 5) Repeat the same pr ocedure in Insert G2 character s setting . 6) Scan Exit barcode. 1) Insert data group 1-4 position. Please refer to the specific barcode that you want to use. 2) Insert dat a group 1-4 position: Th e imager offer s 4 positions to insert a mong the sy mbol.
129 Option Bar Code Optio n A lphanumeric Entry Insert G1 character s setting 1-22 characters “GROUP1” 00-ffH ASCII code Insert G2 character s setting 1-22 characters “GROUP2” 00-ffH ASCII cod.
130 Exit Insert data group 2 position 00-64 (00: no insertion) 00-64 00 Insert data group 3 position 00-64 (00: no insertion) 00-64 00 Insert data group 4 position 00-64 (00: no insertion) 00-64 00.
131 String setting / T ransmiss ion (Others) Code ID position: Upon your usa ge, the transmitting position of Code ID can be selected to pla ce Before Code Data or After Code Dat a when it is transmitted. Code ID transmissio n: If your ap plication is needed to transmit Code ID, yo u must set thi s to Propriet ary ID or A IM ID.
132 Exit Code ID position Before code data After code data 00 01 Code ID transmission Disable Proprietary ID AIM ID 00 01 02 Code length transmission Disable Enable 00 01 Code name transmission Disabl.
133 CODABAR-P ARA CODE-1 1 P .
134 PDF-417 * ST ANDRAD-25 P ARA CODE-16K EAN-8 P ARA * INDUSTRIAL-25 P ARA UPCE P ARA *.
135 INTERLEA VED-25 P ARA * MA T RIX 25 P ARA MSI/PLESSEY P ARA UPCA P ARA * UK/PLESSEY P ARA RSS Micro-PD F *.
136 ASCII Code T ab le.
137 Parameter Setting List Program Barcode st andard p arameter setting list If you wish to display the current b arcode reading configuration of yo ur AS-8020CL i mager over the ho st terminal/computer , scan the Barco de standard p ara meter setting list bar code.
138 Exit Query present cradle firm ware version Program F irmware versio n list If you wish to display the cradle an d imager firmware ver sions, scan the “Firm ware ver sion list” barcode.
139 0 1 2 3 4 5 6 7 8 9 A B C Finish F E D.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Argox AS-8020CL è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Argox AS-8020CL - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Argox AS-8020CL imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Argox AS-8020CL ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Argox AS-8020CL, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Argox AS-8020CL.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Argox AS-8020CL. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Argox AS-8020CL insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
