Manuale d’uso / di manutenzione del prodotto GS510TP-100NAS del fabbricante NETGEAR
Vai alla pagina of 32
350 East Plumeria Drive San Jose, CA 95134 USA October 2011 202-10886-01 1.0 NETGEAR GS510TP Smart Switch Hardware Installation Guide.
2 NETGEAR GS510TP Smart Switch © 2011 NETGEAR, Inc. All rights reserved No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc.
3 Contents About This Manual Conventions, Formats, and Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 How to Print this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chapter 1 Introduction Overview.
4 NETGEAR GS510TP Smart Switch Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Additional Troubleshooting Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Network Adapter Cards .
5 0 0. About This Manual The NETGEAR ® ProSafe TM GS510TP Hardware Installation Guide describes how to install and power on the GS510TP Smart Switch. The information in this manual is intended for readers with intermediate computer and Internet skills.
This is a safety warning. Failure to take heed of this notice may result in personal injury or death. 6 NETGEAR GS510TP Smart Switch • Scope. This manual is written for the GS510TP Smart Switch acco.
7 1 1. Introduction Congratulations on the purchase of your NETGEAR ® ProSafe TM GS510TP Smart Switch. The GS510TP is a supplement to the Gigabit Advanced Smart Switch family. Available as a desktop or rack-mountable.The GS510TP is a PoE-supportable low-port switch with two fiber uplinks included.
Introduction 8 NETGEAR GS510TP Smart Switch full-duplex mode. The maximum segment length is 328 feet (100 meters) over Category 5 Unshielded Twisted-Pair (UTP) cable. Features The following list identifies the key features of the GS510TP Smart Switch: • Eight RJ-45 10/100/1000 Mbps autosensing Gigabit Ethernet switching ports.
Introduction 9 NETGEAR GS510TP Smart Switch • PoE is enabled by default. Green Features The GS510TP Smart Switch supports the following power-saving features: • The power consumption automatically adjusts based on the RJ-45 cable length. • Each port is configured to power down automatically when the port link is down.
Introduction 10 NETGEAR GS510TP Smart Switch.
11 2 2. Physical Description This chapter describes the NETGEAR GS510TP Smart Switch hardware features. Topics include: • GS510TP Front-Panel Configuration • LED Designations • Device Hardware Interfaces GS510TP Front-Panel Configuration The GS510TP has eight 10/100/1000 Mbps autosensing and two 1000 Mbps SFP Gigabit Ethernet switching ports.
Physical Description 12 NETGEAR GS510TP Smart Switch • Fan LED • PoE Max LED GS510TP Back-Panel Configuration Figure 3 illustrates the GS510TP back panel. Power Connector Figure 3. GS510TP Back Panel The back panel contains the following: • Internal 150W open frame power supply for the GS510TP.
Physical Description 13 NETGEAR GS510TP Smart Switch LED Designations Port LEDs Table 1 describes the RJ-45 and SFP port LED designations. There are two LEDs for each RJ-45 port. Table 1. Port LEDs LED Designation Speed/Link/Activity SPD/Link/ACT LED: • Off = No link is established on the port.
Physical Description 14 NETGEAR GS510TP Smart Switch System LEDs Table 2 describes the system LED designations. Table 2. System LEDs LED Designation Power/Status LED • Solid Green = Power is supplied to the switch and the switch is operating normally.
Physical Description 15 NETGEAR GS510TP Smart Switch device such as a paper clip into the opening to press the recessed button. The front-panel LEDs should extinguish and light again as the switch performs its Power On Self Test (POST).
Physical Description 16 NETGEAR GS510TP Smart Switch.
17 3 3. Applications Your NETGEAR GS510TP Smart Switch is designed to provide flexibility in configuring your network connections. It can be used as a stand-alone device or with 10 Mbps, 100 Mbps, and 1000 Mbps hubs and switches.
Applications 18 NETGEAR GS510TP Smart Switch.
19 4 4. Installation This chapter describes the installation procedures for your NETGEAR GS510TP Smart Switch. Switch installation involves the following steps: Step 1: Preparing the Site Step 2: Inst.
Installation 20 NETGEAR GS510TP Smart Switch Step 2: Installing the Switch The GS510TP Smart Switch can be used on a flat surface or mount in a rack. Installing the Switch on a Flat Surface The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the four concave spaces on the bottom of the switch.
Installation 21 NETGEAR GS510TP Smart Switch Step 3: Checking the Installation Before applying power to the switch, perform the following: • Inspect the equipment thoroughly. • Verify that all cables are installed correctly. • Check cable routing to make sure cables are not damaged or creating a safety hazard.
Note: The PoE port may be considered SELV circuits, if it is not likely to require connection to an Ethernet network with outside plant routing, including campus environment; and the installation instructions clearly state that the ITE is to be connected only to PoEnetworks without routing to the outside plant.
Note: When the device powers up, there is a default IP address already configured on the device. The default IP address is 192.168.0.239 and subnet mask 255.
Installation 24 NETGEAR GS510TP Smart Switch.
25 A A. Troubleshooting This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics include the following: • Troubleshooting Chart • Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems.
Troubleshooting 26 NETGEAR GS510TP Smart Switch Additional Troubleshooting Suggestions If the suggestions in Troubleshooting Chart do not resolve the problem, refer to the troubleshooting suggestions in this section.
27 B B. Technical Specifications Network Protocol and Standards Compatibility IEEE 802.3i 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x flow control IEEE 802.3z 1000BASE-X IEEE 802.3at DTE Power via MDI Management Windows 2000 + XP, Vista; Microsoft Explorer 6.
Technical Specifications 28 NETGEAR GS510TP Smart Switch Protected Port IP and MAC ACL Green feature (Auto power down and Short cable power saving) DoS protection Interface Eight RJ-45 connectors for .
Technical Specifications 29 NETGEAR GS510TP Smart Switch Operating humidity: 10% to 90% maximum relative humidity, noncondensing Storage temperature: –20°C to 70°C (–4 to 158°F) Storage humidit.
Technical Specifications 30 NETGEAR GS510TP Smart Switch.
31 Index Numerics 8-pin 14 A Applying AC Power 22 Auto Uplink 14 Auto-negotiating 8 Autosensing 8 , 14 B Backpressure 8 C Category 5 Unshielded Twisted-Pair 8 Checking the Installation 21 Class of Ser.
32 NETGEAR GS510TP Smart Switch Preparing the Site 19 R Rack-mount Kit 9 Reset Button 11 RJ-45 7 RJ-45 Ports 14 Rubber footpads 9 , 20 S Site Requirements 19 Smart Switch Resource CD 9 Straight-throug.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il NETGEAR GS510TP-100NAS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del NETGEAR GS510TP-100NAS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso NETGEAR GS510TP-100NAS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul NETGEAR GS510TP-100NAS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il NETGEAR GS510TP-100NAS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del NETGEAR GS510TP-100NAS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il NETGEAR GS510TP-100NAS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo NETGEAR GS510TP-100NAS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
