Manuale d’uso / di manutenzione del prodotto GS110TP-100NAS del fabbricante NETGEAR
Vai alla pagina of 32
202-10596-01 March 2010 v1.0 NETGEAR , Inc. 350 East Plumeria Drive San Jose, California 95134 USA GS110TP Hardware Installation Guide.
ii v1.0, March 2010 © 2010 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR, the NETGEAR logo, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
Contents iii v1.0, March 2010 Contents GS110TP Hardware Installation Guide About This Manual Conventions, Formats, and Scope .................................................................................... v How to Print this Manual ..............
iv Contents v1.0, March 2010 Chapter 4 Installation Step 1: Preparing the Site .............................................................................................. 4-1 Step 2: Installing the Switch ...........................................
v v1.0, March 2010 About This Manual The NETGEAR ® ProSafe TM GS110TP Hardware Installation Guide describes how to install and power on the GS110TP Smart PoE Switch. The information in this manual is intended for readers with intermediate computer and Internet skills.
Danger: This is a safety warning. Failure to take heed of this notice may result in personal injury or death. GS110TP Hardware Installation Guide vi About This Manual v1.
1-1 v1.0, March 2010 Chapter 1 Introduction Congratulations on the purchase of your NETGEAR GS110TP Smart PoE Switch. The GS110TP Smart PoE Switch is a supplement to the Gigabit Advanced Smart Switch family. Available as a desktop or wall-mountable switch, the GS110TP Smart PoE Switch is not intended to be rack- mountable.
GS110TP Hardware Installation Guide 1-2 Introduction v1.0, March 2010 The GS110TP Smart PoE Switch is a free-standing switch. It is IEEE-compliant and offers low latency for high-speed networking. All ports can automatically negotiate to the highest speed.
GS110TP Hardware Installation Guide Introduction 1-3 v1.0, March 2010 • Standard NETGEAR 1xx series chassis. • NETGEAR Green product features. • External 48V/1.25A PA. PoE Features The GS110TP Smart PoE Switch supports IEEE 802.3af PSE features: • Ports 1 through 8 support IEEE 802.
GS110TP Hardware Installation Guide 1-4 Introduction v1.0, March 2010 Package Contents Figure 1-1 shows the package contents of the NETGEAR GS110TP Smart PoE Switch.
2-1 v1.0, March 2010 Chapter 2 Physical Description This chapter describes the NETGEAR GS110TP Smart PoE Switch hardware features. Topics include: • GS110TP Front and Back Panel Configuration • LE.
GS110TP Hardware Installation Guide 2-2 Physical Description v1.0, March 2010 • Power and Status LED • PoE Max LED Figure 2-2 illustrates the NETGEAR GS110TP Smart PoE Switch back panel. Power Connector Figure 2-2 The back panel contains the following: • A DC input for the supplied 48V/1.
GS110TP Hardware Installation Guide Physical Description 2-3 v1.0, March 2010 System LEDs The following table describes the system LED designations. Table 2-2. System LEDs LED Designation Power/Status LED • Solid Green = Power is supplied to the switch and the switch is operating normally.
GS110TP Hardware Installation Guide 2-4 Physical Description v1.0, March 2010 To simplify the procedure for attaching devices, all RJ-45 ports support Auto Uplink. This technology allows attaching devices to the RJ-45 ports with either straight-through or crossover cables.
3-1 v1.0, March 2010 Chapter 3 Applications Your NETGEAR GS110TP Smart PoE Switch is designed to provide flexibility in configuring your network connections. It can be used as a stand-alone device or with 10 Mbps, 100 Mbps, and 1000 Mbps hubs and switches.
GS110TP Hardware Installation Guide 3-2 Applications v1.0, March 2010.
4-1 v1.0, March 2010 Chapter 4 Installation This chapter describes the installation procedures for your NETGEAR GS110TP Smart PoE Switch. Switch installation involves the following steps: Step 1: Prep.
GS110TP Hardware Installation Guide 4-2 Installation v1.0, March 2010 Step 2: Installing the Switch The GS110TP Smart PoE Switch can be used on a flat surface or mounted on the wall. Installing the Switch on a Flat Surface The switch ships with four self-adhesive rubber footpads.
GS110TP Hardware Installation Guide Installation 4-3 v1.0, March 2010 Step 3: Checking the Installation Before applying power to the switch, perform the following: • Inspect the equipment thoroughly. • Verify that all cables are installed correctly.
GS110TP Hardware Installation Guide 4-4 Installation v1.0, March 2010 Connect each PC to an RJ-45 network port on the Switch front panel ( Figure 4-1 ). Use Category 5 (Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector to make these connections.
Note: When the device powers up, there is a default IP address already configured on the device. The default IP address is 192.168.0.239 and subnet mask 255.
GS110TP Hardware Installation Guide 4-6 Installation v1.0, March 2010.
Troubleshooting A-1 v1.0, March 2010 Appendix A Troubleshooting This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics include the following: • Troubleshooting Chart • Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems.
GS110TP Hardware Installation Guide A-2 Troubleshooting v1.0, March 2010 Additional Troubleshooting Suggestions If the suggestions in Troubleshooting Chart do not resolve the problem, refer to the troubleshooting suggestions in this section.
GS110TP Hardware Installation Guide Troubleshooting A-3 v1.0, March 2010 Auto-Negotiation The RJ-45 ports negotiate the correct duplex mode and speed if the device at the other end of the link supports auto negotiation.
GS110TP Hardware Installation Guide A-4 Troubleshooting v1.0, March 2010.
Technical Specifications B-1 v1.0, March 2010 Appendix B Technical Specifications Network Protocol and Standards Compatibility IEEE 802.3i 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x flow control IEEE 802.3z 1000BASE-X IEEE 802.
GS110TP Hardware Installation Guide B-2 Technical Specifications v1.0, March 2010 Interface Eight RJ-45 connectors for 10BASE-T, 100BASE-TX, and 1000BASE-T (Auto Uplink™ on all ports) Two SFP slots .
GS110TP Hardware Installation Guide Technical Specifications B-3 v1.0, March 2010 Electromagnetic Emissions FCC Class B CE Class B: Includes EN55022 (CISPR 22), 55024, and 50082-1 VCCI Class B C-Tick .
GS110TP Hardware Installation Guide B-4 Technical Specifications v1.0, March 2010.
Index-1 v1.0, March 2010 Index Numerics 1U 1-3 8-pin 2-3 A Applying AC Power 4-4 Auto Uplink 2-4 Auto-negotiating 1-2 Autosensing 1-2 , 2-3 B Backpressure 1-2 C Category 5 Unshielded Twisted-Pair 1-2 .
GS110TP Hardware Installation Guide Index-2 v1.0, March 2010 O Operating Conditions 4-2 Operating Environment 4-1 Operating humidity 4-2 Overview 1-1 P Package Contents 1-4 Pause Frame Flow Control 1-.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il NETGEAR GS110TP-100NAS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del NETGEAR GS110TP-100NAS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso NETGEAR GS110TP-100NAS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul NETGEAR GS110TP-100NAS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il NETGEAR GS110TP-100NAS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del NETGEAR GS110TP-100NAS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il NETGEAR GS110TP-100NAS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo NETGEAR GS110TP-100NAS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
