Manuale d’uso / di manutenzione del prodotto 6017 del fabbricante Monarch
Vai alla pagina of 28
Monarch 6017 Han diP ri nt Prin ter TC60 17OI Rev . AB 4/01 ©20 00 M onarch Markin g System s, Inc. A ll righ ts reser ved.
Each produc t and pro gram c arries a r espective written wa rranty , the on ly war ranty on which the cu stomer can rely . Mona rch r eserve s the righ t to ma ke change s in the prod uct, the pr ograms, and their ava ilability at any tim e an d without n otice.
i TABLE OF CONTENTS GETTING STARTED ................................................. 1 - 1 Unpacking the Printer ............................................ 1 - 1 Programming Information ....................................... 1 - 1 Battery and Safety Information .
ii.
Getting Started 1 - 1 GETTING S TARTED Use these operating instructions with your Monarch 6017 HandiPrint Printer. The printer works with the SYMBOL SPT 17 00 or PPT 2700 handheld computer (“handheld”). The printer can print text, bar codes, and limited graphics on thermal direct receipt paper.
1 - 2 Getting Started Battery and Safety Information The printer is powered by a 7.4V Lithium Ion (LiIon) battery. There are no memory effects with LiIon batteries and reconditioning is not required. Lithium ion batte ries do not have to be completely drained before charging.
Getting Started 1 - 3 3. Open the strap at the VELCRO tab and pull the strap through the slot. You now have access to the battery door. Move the strap out of the way. 4. Unlock the battery door by sliding down the battery tab. 5. Open the battery door.
1 - 4 Getting Started 6. Insert the battery into the printer as shown. 7. Press the battery into place. 8. Lock the battery door by pushing up the battery tab. 9. Thread the strap through the slot and secu re the strap at the VELCRO tab. Make sure the strap is adjusted to fit your hand.
Getting Started 1 - 5 You can print while the battery is charging; howeve r, the battery may not receive a full charge. You can also charge the handheld while it is connected to the printer. However, the batteries (printer and handheld) may not receive a full charge.
1 - 6 Getting Started Reading the LED This table explains the LED indicator. LED Indicator Status Red On The charger is charging the battery at a fast rate. If the ba ttery voltage is below 5.0V, the battery is “trickle” charged until the battery reaches 5.
Getting Started 1 - 7 Connecting the Printer Attach the handheld to the prin ter's 14 - pin connector as shown. The handheld’s bottom lip fits snugly under the printer’s cutout.
1 - 8 Getting Started 3. Using the grommet provided, secure the strap into the attaching hole. 4. Thread the strap through the slot and secure the s trap at the VELCRO tab. Make sure the strap is adjusted to fit your hand. 5. Using the self - tapping Phillips screw provided, secure the button to the strap grommet.
Loading Supplies 2 - 1 LOADING SUPPLIES The printer can print text, bar codes, and some limited graphics on thermal direct receipt paper. See Appendix A, “Specifications” for the width and thickness requirements. 1. Open the supply cover by inserting your fingers into the rubber pull tab and pulling up firmly on the supply cover as shown.
2 - 2 Loading Supplies 2. Drop the supply into the well. Make sure the supply unwinds from t he top as shown. 3. Position the supply between the printhead guides. 4. Make sure some supply extends past the platen roller. 5. Close the supply cover. Tearing Supply The printer’s supply door acts as a tear bar.
Using the Printer 3 - 1 USING THE PRINTER This chapter includes information about printing, using the magnetic stripe reader, and scanning bar codes. Printing You must have a printing application installed on your handheld b efore you can print receipts.
3 - 2 Using the Printer Quickly swipe the card through the reader either left - to - right or right - to - left with the magnetic stripe in the reader. The magnetic stripe must be facing toward the handheld while it is passed through the reader. The green LED on the printer indicates the following: LED Indicator Status On Ready/waiting for card.
Using the Printer 3 - 3 Scanning Bar Codes Scanning bar codes is application specific. You should only scan a bar code when prompted by your application. 1. Point the scanner at a slight angle approximate ly four to eight inches from the bar code symbol.
3 - 4 Using the Printer Scanning Tips ♦ Make sure there are no voids in the bar code symbol. ♦ Hold the scanner four to eight inches from the bar code. Move the scanner toward and away from the bar code to find the correct distance for a successful scan.
Cleaning 4 - 1 CLEANING You may need to clean the printhe ad and platen roller after printing approximately six rolls of supply, whenever you load new supplies, or when you see voids in the print as shown. CAUTION Do not use sharp objects to clean the printhead.
4 - 2 Cleaning 4. Clean the platen roller with a dry cloth or small brush. You can also use another cotton swab moistened with isopropyl alcohol. Turn the platen roller with your finger and run the cotton swab or dry cloth across it. Make sure the platen roller is clean all the way around.
Troubleshooting 5 - 1 TROUBLESHOOTING If you cannot fix a problem, call Technical Support. Problem Action Does not feed or has a paper jam. Remove any jammed supplies. Reload supplies. Does not print. ♦ Check or replace the printer’s battery. ♦ Your handheld’ s application may include a query for the battery voltage.
5 - 2 Troubleshooting Problem Action Light /heavy printing or voids in printing. Clean the printhead. Check or recharge the battery. See “Charging the Battery” in Chapter 1 for more information. Your System Administrator may need to adjust the print contrast.
Specifications A - 1 SPECIFIC ATIONS Printer Specifications Height: 2.8 inches (71 mm) Width: 4.25 inches (108 mm) Length: 9.5 inches (241 mm) Weight: w/ battery & supply 1.
A - 2 Specifications Charging Time: Approximately 3 hours with no printing Communicatio ns: RS - 232 port Print Ratio 25% black maximum per square inch Supply Specifications Supplies: Thermal direct receipt paper Supply Thickness: 2.2 to 3.5 mils (receipt paper) Supply Width: 3.
Specificatio ns A - 3 Using the Optional Stand Read the following if you purchased the optional printer stand. The stand can be ♦ used on a table top or wall - mounted. ♦ adjusted to minimize glare on the handheld’s display ♦ folded flat for storage.
A - 4 Specifications For Wall - Mounting: Wall - mounting hardware is not included. Use two screws or nails that support at least 5 pounds (2.3 kg.). 1. Place the unfolded stand against the wall. 2. Use a pencil to mark inside the two keyholes for the screws or nails.
.
For supplies, service, or assistance call toll free: 1-800-543-6650 (In the U.S.A.) 1-800-263-4650 (In Canada) www .monar ch.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Monarch 6017 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Monarch 6017 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Monarch 6017 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Monarch 6017 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Monarch 6017, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Monarch 6017.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Monarch 6017. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Monarch 6017 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
