IT
Ariens logo
Manuale d'uso ufficiale

Ariens 992235

6 pagine·613 KB·Rasaerba·PDF·EN
Ariens 992235
Indice dei contenuti 6 sezioni Product Family: Pro-Turn 400 Mowers · Subject: Possible Foot Plate Weld Fracture · Dealer Action: Inspect and Install Kit · Model · … MostraNascondi
Page 1 of the Ariens 992235 user manual — Service Bulletin
Pagina 1 · clicca per ingrandire
Pagina 1
DateAugust 21, 2012 No. B-2093

Service Bulletin

Ariens Company 655 W. Ryan St. Brillion, WI 54110 www.gravely.com

Product FamilyPro-Turn 400 Mowers
SubjectPossible Foot Plate Weld Fracture
Dealer ActionInspect and Install Kit
ModelSerial Number RangeDescription 992230101 – 177, 179 – 181, 183 – 184, 186 – 187, 192 – 196, 198 – 205, 208 – 223, 225, 227 – 229, 231 – 233Pro-Turn 452 992231101 – 111, 114 – 118, 121 – 122, 124 – 125, 130, 136, 138 – 140, 143 – 144, 146 – 147, 150 – 151, 156, 159, 161, 167, 169, 173, 175, 180, 183, 185, 187Pro-Turn 452 992232101 – 109, 111 – 120, 122 – 128, 130 – 139, 141 – 142, 144, 147, 152, 154, 156 – 157, 159, 171 – 174, 183 – 184, 196 – 197, 199 – 200, 204Pro-Turn 460 992233101 – 266, 268 – 284, 286 – 371Pro-Turn 460 992234101 – 181, 183, 186 – 198, 200 – 202, 204 – 243,246 – 249, 255, 258 – 261, 263 – 265,267, 269, 271, 275 – 287, 290 – 291, 293 – 299, 302 – 303, 310 – 312, 314 – 317, 322 – 325, 327 – 328, 333, 335, 342, 345, 354 – 355,361, 368, 370 – 373, 377, 380, 383 – 384, 386, 388 – 389, 392 – 397,400 – 404, 406, 409, 412Pro-Turn 460 992235101 – 874Pro-Turn 460 992238101 – 124, 126 – 162, 164 – 166Pro-Turn 466 992239101 – 292, 294, 296 – 300, 302 – 308, 314 – 316, 318, 501 – 504, 506 – 508, 510 – 514, 517 – 520, 522 – 524, 526 – 527, 529Pro-Turn 472

Ariens Company has received a limited number of reports of fractured welds on the foot plate of the Gravely Pro-Turn 400 series commercial mowers in the model and serial number ranges listed above. The foot plate is not a structural component of the frame, so this crack will not affect the structural integrity of the machine. However, the fractured welds are cosmetically unpleasing and over time the foot plate may come loose due to vibration.

To address this issue, Ariens Company has developed two cradle plates kits:

  • 59214800 (52", 60" and 66" models)
  • 59214900 (72" models).

The cradle plates in these kits stiffen the foot plate mounting area of the machine to prevent cracks from developing at the welds. The kits include the cradle plates along with other supplies needed to install the plates. Because welding will be required, primer and touch up paint are included. Attached is an installation instruction sheet for the kits.

Page 1 of 2

Page 2 of the Ariens 992235 user manual — Product Family: Pro-Turn 400 Mowers
Pagina 2 · clicca per ingrandire
Pagina 2
DateAugust 21, 2012 No. B-2093

Please note the following important items:

  • All PT400 models shipped from Ariens Company after 7/23/2012 have been manufactured with the cradle plates installed on the frame below the foot plate.
  • All unsold dealer inventory is to be updated with 59214800 or 59214900 prior to sale.
  • A certified welder should be used to do the welding portion of the repair.
  • All registered owners of Pro-Turn 400 units will be contacted by letter from Ariens Company about this issue. Customers will be made aware that the foot plate weld may fracture and instructed to contact their dealer if the problem occurs.
  • Normal warranty applies. Flat rate for installation of 59214800 and 59214900 is 3.0 hours.
  • The installation of kits 59214800 or 59214900 on a Pro-Turn 400 unit with an 892040 bagger installed will require changing the front weight bracket p/n 03969351 to p/n 04555851 to provide additional clearance for the cradle plate. Refer to Service Bulletin B-2094 for more information about this change.

Page 2 of 2

Page 3 of the Ariens 992235 user manual — INSTALLATION
Pagina 3 · clicca per ingrandire
Pagina 3

Instruction Sheet Kit Number: 59214800 & 59214900

FOOT PLATE REPAIR INSTRUCTIONS

Ariens 992235 — FOOT PLATE REPAIR INSTRUCTIONS diagram (page 3)
Fig. 1
For use on models59214800: 992230, 992231, 992232, 992233, 992234, 992235, 992238
59214900992239
Ariens 992235 — FOOT PLATE REPAIR INSTRUCTIONS diagram (page 3)
Fig. 2

Read, understand, and follow all safety practices in Owner/Operator Manual before beginning.

Package Contents Check the contents of your kit for the parts listed below (Figure 1):

Ariens 992235 — FOOT PLATE REPAIR INSTRUCTIONS diagram (page 3)
Fig. 3

1 Cradle Plate (52, 60, 66" Decks) Cradle Plate (72" Decks)

2 1/2"-13 x 1 1/4" Round Head Square Neck Bolt

INSTALLATION

3 9/16" x 1 3/8" x 7/64" Flat Steel Washer

Remove Mower Deck IMPORTANT: If desired the mower deck does not need to be completely removed. If this repair method is chosen the PTO belt is removed, the rear mounting pins are left in place and the deck allowed to pivot down as the front of the tractor is lifted. If deck remains attached to the tractor a welding blanket must be used to protect the deck during welding.

Ariens 992235 — INSTALLATION diagram (page 3)
Fig. 4
1. Remove PTO belt.
Ariens 992235 — INSTALLATION diagram (page 3)
Fig. 5

Springs store energy. Keep body parts well away from pinch points when removing the deck.

  • © Copyright 2012
  • Ariens Company
  • Brillion, WI 54110 08400165A 8/12 Page 1 of 4
Page 4 of the Ariens 992235 user manual — Product Family: Pro-Turn 400 Mowers
Pagina 4 · clicca per ingrandire
Pagina 4
12. Fully remove the paint in the marked areas (see figure 3 on page 2). Take care not to remove any steel. Clean area thoroughly prior to welding.
2. Remove hardware retaining foot plate and remove.
Ariens 992235 — Product Family: Pro-Turn 400 Mowers diagram (page 4)
Fig. 6 · Product Family: Pro-Turn 400 Mowers
3. Raise the deck to the transport position and disconnect the lift assist springs (6) from the mower lift arms (1) on each side of the deck.
4. Slowly lower the deck to its lowest position.
5. Remove hardware retaining all four mower lift links (2) from mower lift arms.
6. Remove the rear mower mounting pins (4) connecting the mower mounting arms (3) to the deck.
7. Slide mower deck out from under unit.
Ariens 992235 — Product Family: Pro-Turn 400 Mowers diagram (page 4)
Fig. 7 · Product Family: Pro-Turn 400 Mowers
Ariens 992235 — Product Family: Pro-Turn 400 Mowers diagram (page 4)
Fig. 8 · Product Family: Pro-Turn 400 Mowers

Remove paint from all areas to be welded.

13. Mount and install cradle plate (item 1) using two 1/2 bolts (item 2), two flat washers (item 3), and two flange nuts (item 4). Ensure that cradle plate is centered and properly aligned before tightening hardware (see Weld Guide on page 4).
Ariens 992235 — Product Family: Pro-Turn 400 Mowers diagram (page 4)
Fig. 9 · Product Family: Pro-Turn 400 Mowers
14. Using C-clamps and/or locking pliers ensure that all four welding surfaces are mated properly.
15. Weld the cradle plate into position using the weld guide (see Weld Guide on page 4). If the deck is still mounted to the tractor protect it with a welding blanket.
1. Mower Lift Arm 2. Mower Lift Link 3. Mower Mounting Arm 4. Mower Mounting Pin 5. Mounting Hardware 6. Lift Assist Spring
16. Upon completion of welding allow frame to cool completely.
17. Dress welds as necessary and clean all areas completely with isopropyl alcohol.
8. Remove front right and left lift arms.
9. From below front foot plate loosely install cradle plate (item 1) using two 1/2 bolts (item 2) and two flange nuts (item 4).
18. Coat all welds an unprotected steel with galvanizing primer (item 7). Follow application instructions on primer can.
19. Coat all welds and unprotected steel with enamel paint provided with kit.
10. Using cradle plate as a template, mark off an area at least 3/4" from the edge of the cradle plate in all areas to be welded (see Weld Guide on page 4).
11. Remove the cradle plate and hardware.

08400165A 8/12 Page 2 of 4

Page 5 of the Ariens 992235 user manual — Product Family: Pro-Turn 400 Mowers
Pagina 5 · clicca per ingrandire
Pagina 5
Ariens 992235 — Product Family: Pro-Turn 400 Mowers diagram (page 5)
Fig. 10 · Product Family: Pro-Turn 400 Mowers
Ariens 992235 — Product Family: Pro-Turn 400 Mowers diagram (page 5)
Fig. 11 · Product Family: Pro-Turn 400 Mowers
20. Reinstall deck and adjust per procedure found in owner’s manual.
21. Reinstall foot plate.

08400165A 8/12 Page 3 of 4

Page 6 of the Ariens 992235 user manual — WELD GUIDE
Pagina 6 · clicca per ingrandire
Pagina 6

WELD GUIDE

Weld cradle plate to frame in the areas shown below.

Ariens 992235 — WELD GUIDE diagram (page 6)
Fig. 12

08400165A 8/12 Page 4 of 4

Fonti

Riferimenti e link

Pagine di riferimento in questo manuale: produttore, supporto e download.

Fai una domanda su Ariens 992235

I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nessuna domanda ancora per il dispositivo Ariens 992235

Invia la prima domanda: risponderanno altri possessori o il nostro team.

Documento originale

Ariens 992235 manuale in PDF

6 pagine·613 KB·Rasaerba·PDF
Clicca su qualsiasi pagina in alto per aprirla qui
Pagina 1 / …
100%
Caricamento pagine…