Manuale d’uso / di manutenzione del prodotto 882.00273.00 del fabbricante Mitsubishi Electronics
Vai alla pagina of 101
Gravimetric Slide Gate Batch Blender Mitsubishi Controller Part Number: 882.00273.0 0 Bulletin Number: BF1-615.3 Effective: 11/07/07 Write Down Your Serial Numbers Here For Future Reference: _________.
BF1-615.3 ii Shipping Info Unpacking and Inspection You should inspect your equipm ent for possible shipping damage. Thoroughly check the equipment for any dam age th at might have occurred in transit, such as broken or loose wiring and components, l oose hardware and m ounting screws, etc.
BF1-615.3 iii Credit Returns Prior to the return of any material, authorization m ust be given by the manufacturer. A RMA number will be assigned for the equipment to be returned. Reason for requesting the return must be given. ALL returned material purchased from the manufacturer returned is subject to 15% ($75.
BF1-615.3 iv Table of Contents CHAPTER 1: SAFETY ................................................................ 7 1-1 How to Use This Manual ............................................................................................. 7 Safety Symbols Used in this Manual .
BF1-615.3 v 3-5 Initial Set-up .............................................................................................................. 35 Mechanical Set-up ........................................................................................
Hopper Additive Feeder Sub-Assembly (Optional).............................................. 79 Weigh Hopper Sub-assembly .............................................................................. 80 Slide Gate Sub-assembly .......................
Chapter 1: Safety 1-1 How to Use This Manual Use this manual as a guide and reference for installing, operating, and maintaining your granulator. The purpose is to assist you in a pplying efficient, proven techniques that enhance equipment productivity.
Figure 1: Safety Tags and Warning Labels Tag Description Tag Description Pinch Point Slide Gate Read Operation & Installation Manual Shear Point Rotating Mixer Earth Ground High Voltage Inside Enclosure PE Protected Earth Ground Shear Hazard Rotating Auger Lifting Point BF1-615.
1-2 Warnings and Precautions Our equipment is designed to provide safe and reliable operation when installed and operated within design specifications, following national a nd local safety codes. This may include, but is not limited to OSHA, NEC, CSA, SPI, and any other local, national and international regulations.
1-3 Responsibility These machines are constructed for maximum operator safety when used under standard operating conditions and when recommended inst ructions are followed in the maintenance and operation of the machine. All personnel engaged in the use of the machin e should become familiar with its operation as described in this manual.
Learn and always use safe operation. Cooperate with co-workers to promote safe practices. Immediately report any potentially dangerous s ituation to your supervisor or app ropriate person. REMEMBER: • NEVER place your hands or any part of your body in any dangerous location.
Maintenance Responsibility Proper maintenance is essential to safety. If you are a maintenance worker, you must make safety a priority to effectively repair and maintain equipment.
Chapter 2: Functional Description 2-1 Models Covered in This Manual This manual provides operation, installation, an d maintenance instructions for slide gate blenders of various blending rates and specifica tions. See below for a list of available models.
Figure 2: Equipment Specifications 150 500 900 2500 4000 6000 150 (68) 500 (227) 900 (4 10) 2500 (1135) 4000 (1815) 6000 (2725) 2 to 4 2 to 6 2.0 (50) 2.5 (63) 1.5 (38) 2.0 (50) 0.7 (20) 5.2 (145) 0.2 (5) 3.6 (100) 0.07 (2) 0.18 (5) 0.38 (11) 0.82 (23) 1.
2-3 Typical Features and Components Mechanical Features • Exclusive diamond design slide gate meteri ng assemblies meter a large range for free flowing pellet materials • Adjustable Slide gate str.
• Three (3) types of recipe entry procedures available: o Quickset mode (up to 6-component) recipe entry. Color and additives are metered as a percentage of the virgin material. o Percentage mode recipe entry. Ingredients are metered as a percentage of the overall batch.
Slide Gates Air operated slide gates are provided to meter the majority of pellet ingredients on Slide Gate blenders. Note: The metering range assumes 1/8” diam eter free-flowing plastic pellets weighing approximately 35 lbs.
Figure 6: Typical Slide Gate Assembly Each of the diamond gate air cylinders is act uated by a solenoid val ve, which are controlled by the blender controller. When the solenoid valve is energized, it opens the me tering valve cylinder. When the solenoid valve is de-energized, it closes the metering valve cylinder.
Figure 7: Typical Weigh Hopper Assembly The weigh hopper dump door holds the material until it is dum ped into the mixing section. The cylinder is actuated by a solenoid in the valve stack on the side of the blender. In looking at the pneumatic circuit, you can see that the air regulator controls the flow of air to the valve stack.
Mix Chamber All of the batch blenders are equipped with an integr al mix chamber. The mix cham ber holds multiple batches of material so any variations in a batch are averaged over time. Figure 8: Typical Mixer Assembly The Opti-mixer™ is designed to provide bi-d irectional mixing action and can be easily taken apart for cleaning.
Figure 9: Typical Mitsubishi Controller Touch Screen Display Note: The touch-screen panel display on your unit may be slightly different than shown. Figure 10: Controller Pushbuttons & Touchscreen Tags Button Function (Power On) Turns power on to the blender controller.
Figure 11: Typical Operator Screens BF1-615.3 Chapter 2: 1BFunctional Description 22 of 101.
Figure 12: Typical Setup Screens BF1-615.3 Chapter 2: 1BFunctional Description 23 of 101.
BF1-615.3 Chapter 2: 1BFunctional Description 24 of 101.
2-4 Optional Components The following is a list of options, which y our blender may have been equipped with: Pneumatic Slide Gate below Mixer The Slide Gate/Auger blending system can be equipped with an optional pneumatic slide gate below the mixing chamber.
Regrind Auger Metering (R.A.M.) Hopper Used for feeding difficult regrind materials . Figure 15: Typical R.A.M. Hopper Blender Configuration Additive Feeder Hopper Used for feeding pelletized additive, typically used on blenders with more than six components.
2-5 Safety Features This section includes information on safety devices and procedures that are inherent to the Gravimetric Batch Blender. This manual is not in tended to supersede or alter safety standards established by the user of this equipment.
unplug the unit from its power source and tag it out. The plug can then be tagged with any number of approved electrical lockout tags av ailable at most electrical supply stores.
Electric Safety Interlock Switch A unique electric safety switch is used to shut off power to the blender any time the mixer door is opened. Do not alter or tamper with this switch in any way. Figure 19: Electrical Safety Interlock Switch (Located on mixer door) WARNING! Always disconnect and lockout all electrical power and pneumatic (i.
Chapter 3: Inst allation 3-1 Uncrating the Equipment Slide Gate/Auger Blenders are shipped mounted on a skid, enclosed in a plastic wrapper, and contained in a crate. 1. Remove crate from around blender. 2. Secure strap of proper lifting capacity to both lifting lugs (See Figure 20 below.
4. If equipped; adjust the four leveling bolts on the floor stand blender support rails. 5. Mount the material conveying system receivers on the top of the blender suppl y hoppers.
Using proper lifting equipment, lift the blender, us ing the lifting lugs attached to the top plate of the blender. These lifting lugs can also be u sed to fasten horizontal or angled braces to the blender if more stability is needed. Note: Larger blenders need to be braced as part of the installation.
If possible, use rigid tubing. Some flex hose will tend to sag and generate static that could cause de-mixing between the blender and the extruder. Make sure that adequate space is around the blender (36” recommended) to allow proper cleaning, servicing, etc.
3-3 Electrical Connections The standard Slide Gate/Auger blending syst em is designed to oper ate on 120/1/60 suppl y voltage (220/1/50 CE models are also availa ble).
The manufacturer provides all pneumatic lines on the blender piped to a single ¼” NPT standard pipe thread fitting. The Slide Gate/A uger blending system requires approxim ately 1 cfm (1.7 m³/hr) @ 60 psi (4.14 bar) maximu m air pressure for proper operation.
Weigh Hopper Installation Remove the weigh hopper from the shipping box and install it in the blender on the load cell brackets. Connect the airline and close the mixer door, securing the latch.
This screen displays the software version of bo th the PLC and the PanelView. The Controller will stay on this screen for about 10 seconds or you can touch the picture of the blender to quickly skip to the Recipe Scr een (Next Screen in sequence). The software versions are also available on the Panel View Configuration Screen.
Blender Controller Menu Structure 101 “Recipe Book” Page ¾ Sav e the running recipe to the book ¾ Delete a stored re cipe ¾ Load a stored r ecipe ¾ Erase all stored recipes ¾ Modify the produ.
Blender Calibration The load cells on the Auger blender are FACTORY CALIBRATED. Since the load cells can be subject to shock loading during shippi ng, moving, e tc., we recommend that they be recalibrated. The heart of the Auger blending system is the load cell with the supply calibration weight.
Figure 28: Display Calibration Menu Screen 3. Once in “Scale Calibration”, enter in the scale calibration weight value stamped on the side of the weight. 4. The controller will prompt you t o remove the weight hopper and press OK. 5. After touching OK, the controller will display “PLEASE WAIT.
5. Add the calibration weight to each load cell mounting bracket and write down the value displayed in “weight”, as in step 4. 6. Subtract the values recorded in step 4 from st ep 5. This is the measured weight. If the measured weight is within a 0.
3. Select a feeder (1-6) by to uching the “Select Feeder” box. 4. The current settings for the hopper that you have chos en will now be shown on the screen.
Additional Setup Parameters The settings listed below are set at the fact ory and typically do not require any change. 1. From the “Recipe” Page, touch the Manuf acturer’s icon and enter “5413”, then press the “Enter” key.
3-6 Initial Startup The operator can startup the blender by selecting the button that says, “Push to St art or Stop” (startup) on the left side of the Recipe Screen , depending on whether the blender is currently running or is stopped. Simply touch the button to either start or stop the blender.
Chapter 4: Operation 4-1 Start-up General Operation The general operation of the Slide Gate/Auge r blending system is as follows: Once the system is properly installed and set up, the system will be ready for operation. Please see the Installation and Setup chapter in th is manual for further information.
Note: The blender monitors the operator’s en tries and de termin es if the recipe is valid before accepting the new recipe. If there is an error (such as the recipe does not add up to 100% and the blender is in Percentage Mode.) then a message is shown on the Recipe screen to alert the opera tor of the problem.
Operator Displays The Slide Gate/Auger blending system utilizes a standardized menu format. Each screen was designed to be user-friendly and provide th e operator with the necessary information to run the blender. Figure 33: Typical Recipe Entry Operator Screen A typical menu is shown in the figure above.
While the blending system is in operation, there are a couple of dis plays available to the operator. These displays are selected simply by pressing the “NEXT” key when the unit is running. The default display shown when the ble nder is in run mode is the Recipe Screen.
Upon Start Up, the blender controller w ill default to the “Recipe Menu” screen. The “Recipe Book” screen can be accessed in the “Recipe Page” and is useful in storing and retrieving recipes.
“Quickset” Mode (Most common in injection molding) The “Quickset” menu structure allows recipes to be entered and adjusted by touching the buttons on the panel face (for 1 to 6 com ponents) . In this mode, hopper #1 is configured as virgin, hopper #3 is configured as regrind, and the others are configured as additives, i.
Figure 36: Example Calculations of a 5-component blend in “Quickset” mode Virgin (NAT): ??? Additive1 (ADD): 5.00% - of virgin component Regrind (RGD): 30.00% - of total batch Additive2 (ADD): 2.00% - of virgin component Additive3 (ADD): 1.00% - of virgin component Batch Size: 10.
“Percentage” Mode (Most common in extrusion and blow molding) Extrusion processing often requires recipes in per centage format, especially if regrind is not involved, i.e. blown or cast film. In this mode, operators enter in values for each hopper up to 100%.
Because the blending systems must handle a wide variety of materials, with varying bulk densities, the actual amount of weight of material the weigh hopper will hold can vary dramatically from application to application. This feature allows the operator to change the size of the batch to be made.
To enable this feature , simply enter a desired shutdown weight value (from 1 to 999999999) into the Inventory Shutdown displa y line of the Recipe Format screen, under the Setup m enu. This feature can be configured while the bl ender is making a batch.
Selecting “Mixing Time” from the “Mixer and Dump Setup” menu will allow the operator to view the current time setting for the mix timer and to adjust it as needed. The mix timer is set to a default time of four (4) seconds. This time can be adjusted up or down depending on the amount of mi xing n eeded for the materials being blended.
Weigh Hopper Dump Cycle The dump cycle allows the weigh hopper dump valve to c ycle, or open and close, a number of times prior to commencing with the next ba tch cycle. The setting allows from 1 to 9 dump cycles between batches (open and closed cycles).
Max Hopper Weight Exceeded, check batch size: This alarm indicates that the weight in the weigh hopper has exceeded the maximum allo wed weight. This alarm can happen if the operator changes material density and does not perform a feeder calibration, but will usually be automatically fixed after the first batch.
PLC Battery Low: PLC battery is low and may cause the blender to lose both the program and the blender configuration. Notify Maintenance immediately. Figure 45: Typical “PLC Battery Low” Alarm Screen PLC BATTERY LOW Blender Powered On/Off: These are on ly logged in the Alarm Log and does not cause a pop-up message or audible alarm .
Feeder Clean Out Any feeder in the Slide Gate/Auger blending system can be emptied and refilled with a different material. To do a feeder clean out, the operator has to press the “Clean Out” icon key from the recipe screen (the first screen that appears on power up).
Delay” timer. (See Page 51). Once the dump delay timer has timed out, the controller will activate the weigh hopper dump valve, initiating the weigh hopper dum p cycle. The open weigh hopper dump door will allow the material to drop into the mixer section of the blender.
Figure 48: Typical Recipe Book Operator Screen Erase One Stored Recipe Select a Store d Recipe Stored Recipe Details Erase Entire Book Load Stored Recipe Go to Recipe Page Save Running Recipe to the Book The save current recipe to book function allows the operator to save the contents of the current recipe to the recipe book under a desired number.
number which contains the recipe he wishes to view. Once a valid recipe number is entered, the display will indicate the contents of the stored recipe in percentages. Erase Recipe or Entire Book The Erase Recipe or Entire Book function is used to eliminate old or outdated recipes from the recipe book.
8. If any other ingredients need to be changed for the next recipe, simpl y drain the larger hoppers with the drain tubes provided on the side of the hoppers. When the material level is below the drain tube, open the slide gate manually to dump the rest of the material.
Chapter 5: Maintenance 5-1 Preventative Maintenance Schedule The mechanical design of the blender is very si mple and very little maintenance is required.
5-2 Preventative Maintenance Our blenders need periodic maintenance to provide long dependable service. Check these elements regularly: • Check functionality of safety circuit daily. • Maintain proper air pressure and drain water from trap assembly on regulator – as required.
Input Signals to Programmable Controller The Slide Gate/Auger blending system has tw o main input signals that it uses from the blending process: the mix hopper high le vel signa l and the weigh hopper load cells. This, of course, does not include the operator touchscreen input.
Chapter 6: T roubleshooting 6-1 Introduction The utmost in safety precautions should be observed at all times when working on or around the machine and the electrical components. All normal trouble-shooting m ust be accomplished with the power off, line fuses rem oved, and with the machine tagged as out of service.
Problem Corre ctive action Normal after a software upgrade. Follow on-screen instructions. Check the input power. Verify that 110 volts (or 220 volts) are ±10%. This voltage must rem ain constant with all the motors starting and stopping. Insure that the blender is on a “clean” circuit that does not have other equipment on it.
Problem Corre ctive action Check the blender’s scale calibration and verify that the batch hopper is not overfilling. If the hopper is overfilling, adjust your batch size. If this is correct, then you are probably not accounting for material scrap or other items in your process.
Problem Corre ctive action Check the Mixer and Dump Setup to see if the mixer is configured for “Continuous Mixing”. Set it to “Timed Mixing”. Check the value of the mixer timer setting. Check the value of the dump delay timer. Check the mixer motor fuse.
Problem Corre ctive action I can’t calibrate the Scale without an error message. This Is caused by the difference in bits not being large enough. Using the Direct Scale Readout, ex amine current loadcell bits with and without the calibration weight.
Chapter 7: Appendix 7-1 Technical Specifications Equipment Specifications Figure 52: Equipment Specifications 150 500 900 2500 4000 6000 150 (68) 500 (227) 900 (4 10) 2500 (1135) 4000 (1815) 6000 (2725) 2 to 4 2 to 6 2.0 (50) 2.5 (63) 1.5 (38) 2.0 (50) 0.
Annex B Information The following design information is provided for your reference: 1. No modifications are allowed to this equi pment that could alter the CE compliance 2. Ambient temperature: 40 degrees Celsius – Maximum (104 degrees Fahrenheit) 3.
7-2 Drawings and Diagrams Final Assembly Figure 53: Typical Final Assembly Parts List # Description 150 900 2500 4000 6000 1 Mixer Assembly A0771677 A0771682 A0771683 A0771663 A0771691 A0771692 3-Comp.
Mixer Sub-Assembly BF1-615.3 Chapter 7: 6BAppendix 75 of 101.
Figure 54: Typical Mixer Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 FRAME 872.00093.00 872.00094.00 A0770301 872.00224.00 2 FRAME EXTENSION (NOT SHOWN) N/A 872.00225.00 3 TOP PLATE 872.00095.00 872.00096.00 A0770300 872.00226.00 4 MOUNTING BRACKET – MIXER MOTOR 872.
Hopper Sub-assembly Figure 55: Typical Hopper Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 3-COMPONENT HOPPER 872.00118.00 A0569131 872.00240.00 1 2-COMPONENT HOPPER 872.00119.00 A0770299 872.00241.00 3 LEXAN DOOR A0770286 4 DOOR LATCH A0770076 5 3.
Hopper R.A.M. (Regrind Auger Metering) Sub-Assembly (Optional) Figure 56: Typical R.A.M. Hopper Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 THROAT 07822-1 2 CLAMP A0548808 3 FEEDER TUBE # 872.
Hopper Additive Feeder Sub-Assembly (Optional) Figure 57: Typical Additive Feeder Hopper Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 THROAT A0541201 2 MOTOR MOUNT BRACKET A0541229 3 MOTOR – AUGER 51450G 4 THROAT ADAPTER – 2” RISER 872.
Weigh Hopper Sub-assembly Figure 58: Typical Weigh Hopper Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 WEIGH HOPPER 872.00103.00 872. 00104.00 A0770312 872.00229.00 872.00230.00 2 AIR CYLINDER 245.00003.00 A0770248 3 CLEVIS – AIR CYLINDER 35460 35449 4 FITTING – AIR TUBING 35086K 35085K 5 AIR TUBING (NOT SHOWN) 35300K BF1-615.
Slide Gate Sub-assembly Figure 59: Typical Slidegate Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 HOUSING (DOUBLE DIAMOND) (#1-4) 872.00114.00 A0770304 872.00524.00 HOUSING (SQUARE / DIAMOND) (#1-4) A0770308 N/A 1 HOUSING (DOUBLE DIAMOND) (#5-6) 872.
Knife Gate Sub-assembly HD (Optional) Figure 60: Typical Knife Gate (bel ow mixer) Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 BASE FRAME 07990 2 MOLDED THROAT 53413 3 SPACER PLATE 0828.
Knife Gate Sub-assembly RD (Optional) Figure 61: Typical Knife Gate (floor stand) Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 HOUSING FRA ME 872.00297.00 2 GUARD SAFETY COVER 872.00236.00 3 ROD GUIDE 832.00049.00 4 GATE – SLIDE BLADE 872.
Control Panel Layout Figure 62: Typical Mitsubishi Controller Main Parts List # Description 150 500 900 2500 4000 6000 1 Mitsubishi PLC FX2N-32MR A0569702 2 Mitsubishi PLC EEPROM A0569703 3 24 vdc Power Supply A0563932 4 Calex Module – Load Cell Amplifier 724.
7-3 Spare Parts Kits Figure 64: Blender Spare Parts Listing M ode l 150 500 900 2500 4000 6000 KIT "A " (Consumable s) A 0574120 A 0574134 A 0574137 A 0574125 A0574140 A 0574143 Load Cell Assem bly (wit hout pl ug) # 724.00767.00 724.00768.00 724.
7-4 Addendum (Service Supervisor Information) Note: This section of the manual should not be used by untrained personnel – blender controller and/or program can be compromised! Note: Hidden, programmable features and hidden menu pages should not be made available to floor operators.
Figure 66: Typical Engineering Only Setup Screen Go back to Setup Directory Factory Setup Menu Metering Test Screen This screen is useful in both R & D and development purposes when testing the metering performance of each feeder.
This setting should not be m odified exce pt by the developer except under unusual circumstances. Figure 68: Typical Advanced Weight Options Screen 101 Feed Algorithm Options Screen This screen allows the user to configure how the blender metering algorithm works.
Mechanical Options Screen This screen allows the user to change the number of hoppers, the predeterm ined gate cycle time, and the mixer bump time for detecting hi gh level. The gate cycle time has been measured and set at the factory, but might need to be adjusted if we change the mechanical design of the gate, solenoids, and air cylinders.
Customer Setup Menu Units This screen allows the user to change the ble nder’s unit of measurement. The entire blender can be configured in either Kgs. or Lbs., while the Target vs. Actual data can be configured for either regardless of the blender’s units.
Alarm Setup This screen allows the user to configure the f eeder type for each feeder; configure whether a feeder will retry during the metering of a batch, and enable or disable the “Out of Material” alarm for any feeder.
Factory Default Setup Parameters Model Number 150 500 900 25 00 4000 6000 Recipe Entry Mode PERCENT AGE Metering Order Batch Siz e ( lbs) 2.0 4.0 8.0 25.
Model N umber 150 500 900 2500 4000 6000 Hop1 Initial % of Target 100 Hop2 Initial % of Target 99 Hop3 Initial % of Target 100 Hop4 Initial % of Target 99 Hop5 Initial % of Target 99 Hop6 Initial % of Target 99 Hop7 Initial % of Target 99 Hop8 Initial % of Target 99 Hop1 All owed Underfeed (lbs) 0.
7-5 Mitsubishi Communications Manual The Mitsubishi blender uses a FX-2N processor that communicates with the outside world using MELSEC FX protocol over Ethernet hardware. It’s Et hernet speed is 10 Mbits/s econd. The blender must be purchased from ACS with the Ethernet option.
BLENDER ALARMS 1 (R) alarm_number,D1876 (see below for description) 2 (R) hop1_out_of_material,M561 3 (R) hop2_out_of_material,M562 4 (R) hop3_out_of_material, M563 5 (R) hop4_out_of_material, M564 6 .
INVENTORY INF O 1 (RW) clear_inventory,M503 (toggle this to clear a ll inventory, you must also reset this bit after completion) 2 (RW) batch_counter,D1336,LONG VA LUE (number of batches made) 3 (R) h.
RECIPE INFO (THIS IS WHERE YOU RIGHT THE NEW RECIP E TO) 1 (RW) temp_recipe_entry_mode,D1706, SHORT VA LUE (0=percentage mode, 1=parts mode, 2=EZ mode) 2 (R) temp_batch_size_recipe_value,D1234,LONG VALUE (xxx.x lbs or kgs) 3 (RW) pv1_hop1_temp_recipe_value,D1110,LONG VAL UE (xxx.
9 (R) recipe_target_total,D1144,LONG VALUE (xxx.xx, the is the total of hop1-hop6 from above, you must manually add this if you chose to skip the blende rs error checking, you m ust also ensure that y.
Alarm Number Explanation: The alarms are given in individual bits and are reflect ed in the alarm number. The alarm number is only used to drive a pop-up message and will probably not be very useful to you.
WRITING RECIPE EXPLANA TION To write a recipe you must first write to the “temp r ecipe” value locations above. After this is complete you should read the “accept recipe enabled” and the “recipe error” values. If you have a recipe error then you should display the appropriate text.
7-6 Technical Assistance Parts Department Call toll-free 7am–5pm CST [ 800 ] 423-3183 or call [810] 720-7300; Fax [ 810] 720-2598 The ACS Customer Service Group will provide your company with genuine OEM quality parts manufactured to engineering design specifications, which will maximize your equipment’s performance and efficiency.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Mitsubishi Electronics 882.00273.00 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Mitsubishi Electronics 882.00273.00 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Mitsubishi Electronics 882.00273.00 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Mitsubishi Electronics 882.00273.00 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Mitsubishi Electronics 882.00273.00, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Mitsubishi Electronics 882.00273.00.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Mitsubishi Electronics 882.00273.00. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Mitsubishi Electronics 882.00273.00 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
