Manuale d’uso / di manutenzione del prodotto 882.00207.00 del fabbricante Mitsubishi Electronics
Vai alla pagina of 103
Gravimetric Slide Gate Batch Blender Mitsubishi Controller Part Number: 882.00207.0 0 Bulletin Number: BF1-615.1 Effective: 10/3/06 Write Down Your Serial Numbers Here For Future Reference: __________.
Please note that our address and phone i nformation has changed. Please reference this page for updated contact information. These manuals are obsolet e and are provided only for their technical inf ormation, data and capacities.
Bulletin Number ii Shipping Info Unpacking and Inspection You should inspect your equipm ent for possible shipping damage. Thoroughly check the equipment for any dam age th at might have occurred in transit, such as broken or loose wiring and components, l oose hardware and mounting screws, etc.
Bulletin Number iii Returns Do not return any damaged or incorrect items until you receive shipping instructions from the shipping departme nt. Credit Returns Prior to the return of any material, authorization must be given by the manufacturer. A RMA number will be assigned for the equipment to be returned.
Bulletin Number iv Table of Contents CHAPTER 1: SAFETY ................................................................ 7 1-1 How to Use This Manual ............................................................................................. 7 Safety Symbols Used in this Manual .
Bulletin Number v 3-3 Electrical Connections ............................................................................................... 34 3-4 Pneumatic Connections .................................................................................
Bulletin Number vi Customer Responsibilities ................................................................................... 73 7-2 Technical Specifications ..........................................................................................
Bulletin Number Chapter 1: Safety 7 of 102 Chapter 1: Safety 1-1 How to Use This Manual Use this manual as a guide and reference for installing, operating, and maintaining your granulator. The purpose is to assist you in a pplying efficient, proven techniques that enhance equipment productivity.
Bulletin Number Chapter 1: Safety 8 of 102 Figure 1: Safety Tags and Warning Labels Tag Description Tag Description Pinch Point Slide Gate Read Operation & Installation Manual Shear Point Rotating.
Bulletin Number Chapter 1: Safety 9 of 102 1-2 Warnings and Precautions Our equipment is designed to provide safe and reliable operation when installed and operated within design specifications, following national a nd local safety codes.
Bulletin Number Chapter 1: Safety 10 of 102 1-3 Responsibility These machines are constructed for maximum operator safety when used under standard operating conditions and when recommended inst ructions are followed in the maintenance and operation of the machine.
Bulletin Number Chapter 1: Safety 11 of 102 Learn and always use safe operation. Cooperate with co-workers to promote safe practices. Immediately report any potentially dangerous s ituation to your supervisor or app ropriate person. REMEMBER: • NEVER place your hands or any part of your body in any dangerous location.
Bulletin Number Chapter 1: Safety 12 of 102 Maintenance Responsibility Proper maintenance is essential to safety. If you are a maintenance worker, you must make safety a priority to effectively repair and maintain equipment.
Bulletin Number Chapter 2: Functional Description 13 of 102 Chapter 2: Functional Description 2-1 Models Covered in This Manual This manual provides operation, installation, an d maintenance instructions for slide gate blenders of various blending rates and specifica tions.
Bulletin Number Chapter 2: Functional Description 14 of 102 Figure 2: Equipment Specifications 150 500 900 2500 4000 6000 150 (68) 500 (227) 900 (4 10) 2500 (1135) 4000 (1815) 6000 (2725) 2 to 4 2 to 6 2.0 (50) 2.5 (63) 1.5 (38) 2.0 (50) 0.7 (20) 5.2 (145) 0.
Bulletin Number Chapter 2: Functional Description 15 of 102 2-3 Typical Featur es and Components Mechanical Features • Exclusive diamond design slide gate meteri ng assemblies meter a large range fo.
Bulletin Number Chapter 2: Functional Description 16 of 102 • Three (3) types of recipe entry procedures available: o Quickset mode (up to 6-component) recipe entry. Color and additives are metered as a percentage of the virgin material. o Percentage mode recipe entry.
Bulletin Number Chapter 2: Functional Description 17 of 102 Slide Gates Air operated slide gates are provided to meter the majority of pellet ingredients on Slide Gate blenders. A stroke limiter (included) can be installed on the metering gates to lim it their travel.
Bulletin Number Chapter 2: Functional Description 18 of 102 Figure 6: Typical Slide Gate Assembly Each of the diamond gate air cylinders is act uated by a solenoid valve, which are controlled by the blender controller. When the solenoid valve is energized, it opens the me tering valve cylinder.
Bulletin Number Chapter 2: Functional Description 19 of 102 Figure 7: Typical Weigh Hopper Assembly The weigh hopper dump door holds the material until it is dum ped into the mixing section. The cylinder is actuated by a solenoid in the valve stack on the side of the blender.
Bulletin Number Chapter 2: Functional Description 20 of 102 Mix Chamber All of the batch blenders are equipped with an integr al mix chamber. The mix cham ber holds multiple batches of material so any variations in a batch are averaged over time.
Bulletin Number Chapter 2: Functional Description 21 of 102 Figure 9: Typical Mitsubishi Controller Touch Screen Display Figure 10: Controller Pushbuttons & Touchscreen Tags Button Function (Power On) Turns power on to the blender controller. (Found on the back of the controller.
Bulletin Number Chapter 2: Functional Description 22 of 102 Figure 11: Typical Operator Screens.
Bulletin Number Chapter 2: Functional Description 23 of 102 Figure 12: Typical Setup Screens.
Bulletin Number Chapter 2: Functional Description 24 of 102.
Bulletin Number Chapter 2: Functional Description 25 of 102 2-4 Optional Components The following is a list of options, which y our blender may have been equipped with: Pneumatic Slide Gate below Mixer The Slide Gate/Auger blending system can be equipped with an optional pneumatic slide gate below the mixing chamber.
Bulletin Number Chapter 2: Functional Description 26 of 102 Regrind Auger Metering (R.A.M.) Hopper Used for feeding difficult regrind materials . Figure 15: Typical R.A.M. Hopper Blender Configuration Additive Feeder Hopper Used for feeding pelletized additive, typically used on blenders with more than six components.
Bulletin Number Chapter 2: Functional Description 27 of 102 2-5 Safety Features This section includes information on safety devices and procedures that are inherent to the Gravimetric Batch Blender. This manual is not in tended to supersede or alter safety standards established by the user of this equipment.
Bulletin Number Chapter 2: Functional Description 28 of 102 unplug the unit from its power source and tag it out. The plug can then be tagged with any number of approved electrical lockout tags av ailable at most electrical supply stores.
Bulletin Number Chapter 2: Functional Description 29 of 102 Electric Safety Interlock Switch A unique electric safety switch is used to shut off power to the blender any time the mixer door is opened. Do not alter or tamper with this switch in any way.
Bulletin Number Chapter 3: Installation 30 of 102 Chapter 3: Inst allation 3-1 Uncrating the Equipment Slide Gate/Auger Blenders are shipped mounted on a skid, enclosed in a plastic wrapper, and contained in a crate. 1. Remove crate from around blender.
Bulletin Number Chapter 3: Installation 31 of 102 4. If equipped; adjust the four leveling bolts on the floor stand blender support rails. 5. Mount the material conveying system receivers on the top of the blender supply hoppers. 6. Align the weigh hopper on the load cell br ackets.
Bulletin Number Chapter 3: Installation 32 of 102 Using proper lifting equipment, lift the blender, us ing the lifting lugs attached to the top plate of the blender. These lifting lugs can also be u sed to fasten horizontal or angled braces to the blender if more stability is needed.
Bulletin Number Chapter 3: Installation 33 of 102 If possible, use rigid tubing. Some flex hose will tend to sag and generate static that could cause de-mixing between the blender and the extruder. Make sure that adequate space is around the blender (36” recommended) to allow proper cleaning, servicing, etc.
Bulletin Number Chapter 3: Installation 34 of 102 3-3 Electrical Connections The standard Slide Gate/Auger blending syst em is designed to oper ate on 120/1/60 suppl y voltage (220/1/50 CE models are also availa ble). The current requi rements vary with the blender’s size and throughput rating.
Bulletin Number Chapter 3: Installation 35 of 102 The manufacturer provides all pneumatic lines on the blender piped to a single ¼” NPT standard pipe thread fitting. The Slide Gate/A uger blending system requires approxim ately 1 cfm (1.7 m³/hr) @ 60 psi (4.
Bulletin Number Chapter 3: Installation 36 of 102 Weigh Hopper Installation Remove the weigh hopper from the shipping box and install it in the blender on the load cell brackets. Connect the airline and close the mixer door, securing the latch. Figure 25: Weigh Hopper Final Connections Connect the blender to the appropriate power source.
Bulletin Number Chapter 3: Installation 37 of 102 This screen displays the software version of bo th the PLC and the PanelView. The Controller will stay on this screen for about 10 seconds or you can touch the picture of the blender to quickly skip to the Recipe Scr een (Next Screen in sequence).
Bulletin Number Chapter 3: Installation 38 of 102 Blender Controller Menu Structure “Recipe Book” Page ¾ Sav e the running recipe to the book ¾ Delet e a stored re cipe ¾ Load a stored r ecipe .
Bulletin Number Chapter 3: Installation 39 of 102 Blender Calibration The load cells on the Auger blender are FACTORY CALIBRATED. Since the load cells can be subject to shock loading during shippi ng, moving, e tc., we recommend that they be recalibrated.
Bulletin Number Chapter 3: Installation 40 of 102 Figure 28: Display Calibration Menu Screen 3. Once in “Scale Calibration”, enter in the scale calibration weight value stamped on the side of the weight. 4. The controller will prompt you to rem ove the weight hopper and press OK.
Bulletin Number Chapter 3: Installation 41 of 102 5. Add the calibration weight to each load cell mounting bracket and write down the value displayed in “weight”, as in step 4. 6. Subtract the values recorded in step 4 from st ep 5. This is the measured weight.
Bulletin Number Chapter 3: Installation 42 of 102 3. Select a feeder (1-6) by to uching the “Select Feeder” box. 4. The current settings for the hopper that you have chos en will now be shown on the screen.
Bulletin Number Chapter 3: Installation 43 of 102 Additional Setup Parameters The settings listed below are set at the fact ory and typically do not require any change. 1. From the “Recipe” Page, touch the Manuf acturer’s icon and enter “5413”, then press the “Enter” key.
Bulletin Number Chapter 3: Installation 44 of 102 3-6 Initial Startup The operator can startup the blender by selecting the button that says, “Push to Start or Stop” (startup) on the left side of the Recipe Screen , depending on whether the blender is currently running or is stopped.
Bulletin Number Chapter 4: Operation 45 of 102 Chapter 4: Operation 4-1 Start-up General Operation The general operation of the Slide Gate/Auge r blending system is as follows: Once the system is properly installed and set up, the system will be ready for operation.
Bulletin Number Chapter 4: Operation 46 of 102 Existing Recipes The operator can load a previously stored recipe from the Recipe Book. The Recipe book also allows the operators to save the current running recipe. This can be done by perform ing the following steps: 1.
Bulletin Number Chapter 4: Operation 47 of 102 Operator Displays The Slide Gate/Auger blending system utilizes a standardized menu format. Each screen was designed to be user-friendly and provide th e operator with the necessary information to run the blender.
Bulletin Number Chapter 4: Operation 48 of 102 While the blending system is in operation, there are a couple of displays available to the operator. These displays are selected simply by pressing the “NEXT” key when the unit is running. The default display shown when the ble nder is in run m ode is the Recipe Screen.
Bulletin Number Chapter 4: Operation 49 of 102 Upon Start Up, the blender controller w ill default to the “Recipe Menu” screen. The “Recipe Book” screen can be accessed in the “Recipe Page” and is useful in storing and retrieving recipes.
Bulletin Number Chapter 4: Operation 50 of 102 “Quickset” Mode (Most common in injection molding) The “Quickset” menu structure allows recipes to be entered and adjusted by touching the buttons on the panel face (for 1 to 6 com ponents) .
Bulletin Number Chapter 4: Operation 51 of 102 Figure 36: Example Calculations of a 5-component blend in “Quickset” mode Virgin (NAT): ??? Additive1 (ADD): 5.00% - of virgin component Regrind (RGD): 30.00% - of total batch Additive2 (ADD): 2.00% - of virgin component Additive3 (ADD): 1.
Bulletin Number Chapter 4: Operation 52 of 102 “Percentage” Mode (Most common in extrusion and blow molding) Extrusion processing often requires recipes in per centage format, especially if regrind is not involved, i.e. blown or cast film. In this mode, operators enter in values for each hopper up to 100%.
Bulletin Number Chapter 4: Operation 53 of 102 Because the blending systems must handle a wide variety of materials, with varying bulk densities, the actual amount of weight of material the weigh hopper will hold can vary dramatically from application to application.
Bulletin Number Chapter 4: Operation 54 of 102 To enable this feature , simply enter a desired shutdown weight value (from 1 to 999999999) into the Inventory Shutdown displa y line of the Recipe Format screen, under the Setup m enu. This feature can be configured while the bl ender is making a batch.
Bulletin Number Chapter 4: Operation 55 of 102 Selecting “Mixing Time” from the “Mixer and Dump Setup” menu will allow the operator to view the current time setting for the mix timer and to adjust it as needed. The mix timer is set to a default time of four (4) seconds.
Bulletin Number Chapter 4: Operation 56 of 102 Weigh Hopper Dump Cycle The dump cycle allows the weigh hopper dump valve to c ycle, or open and close, a number of times prior to commencing with the next ba tch cycle. The setting allows from 1 to 9 dump cycles between batches (open and closed cycles).
Bulletin Number Chapter 4: Operation 57 of 102 Max Hopper Weight Exceeded, check batch size: This alarm indicates that the weight in the weigh hopper has exceeded the maximum allo wed weight.
Bulletin Number Chapter 4: Operation 58 of 102 PLC Battery Low: PLC battery is low and may cause the blender to lose both the program and the blender configuration.
Bulletin Number Chapter 4: Operation 59 of 102 Feeder Clean Out Any feeder in the Slide Gate/Auger blending system can be emptied and refilled with a different material. To do a feeder clean out, the operator has to press the “Clean Out” icon key from the recipe screen (the first screen that appears on power up).
Bulletin Number Chapter 4: Operation 60 of 102 Delay” timer. (See Page 51). Once the dump delay timer has timed out, the controller will activate the weigh hopper dump valve, initiating the weigh hopper dum p cycle. The open weigh hopper dump door will allow the material to drop into the mixer section of the blender.
Bulletin Number Chapter 4: Operation 61 of 102 Figure 48: Typical Recipe Book Operator Screen Save Running Recipe to the Book The save current recipe to book function allows the operator to save the contents of the current recipe to the recipe book under a desired number.
Bulletin Number Chapter 4: Operation 62 of 102 number which contains the recipe he wishes to view. Once a valid recipe number is entered, the display will indicate the contents of the stored recipe in percentages. Erase Recipe or Entire Book The Erase Recipe or Entire Book function is used to eliminate old or outdated recipes from the recipe book.
Bulletin Number Chapter 4: Operation 63 of 102 8. If any other ingredients need to be changed for the next recipe, simpl y drain the larger hoppers with the drain tubes provided on the side of the hoppers. When the material level is below the drain tube, open the slide gate manually to dump the rest of the material.
Bulletin Number Chapter 5: Maintenance 64 of 102 Chapter 5: Maintenance 5-1 Preventative Maintenance Schedule The mechanical design of the blender is very si mple and very little maintenance is required. The only moving parts are the metering gates, weigh hopper dum p valve, and mixer agitator.
Bulletin Number Chapter 5: Maintenance 65 of 102 5-2 Preventative Maintenance Our blenders need periodic maintenance to provide long dependable service. Check these elements regularly: • Check functionality of safety circuit daily. • Maintain proper air pressure and drain water from trap assembly on regulator – as required.
Bulletin Number Chapter 5: Maintenance 66 of 102 Input Signals to Programmable Controller The Slide Gate/Auger blending system has tw o main input signals that it uses from the blending process: the mix hopper high le vel signa l and the weigh hopper load cells.
Bulletin Number Chapter 6: Troubleshooting 67 of 102 Chapter 6: T roubleshooting 6-1 Introduction The utmost in safety precautions should be observed at all times when working on or around the machine and the electrical components.
Bulletin Number Chapter 6: Troubleshooting 68 of 102 Problem Corrective action Normal after a software upgrade. Follow on-screen instructions. Check the input power. Verify that 110 volts (or 220 volts) are ±10%. This voltage must rem ain constant with all the m otors starting and stopping.
Bulletin Number Chapter 6: Troubleshooting 69 of 102 Problem Corrective action Check the blender’s scale calibration and verify that the batch hopper is not overfilling. If the hopper is overfilling, adjust your batch size. If this is correct, then you are probably not accounting for material scrap or other items in your process.
Bulletin Number Chapter 6: Troubleshooting 70 of 102 Problem Corrective action Check the Mixer and Dump Setup to see if the mixer is configured for “Continuous Mixing”. Set it to “Timed Mixing”. Check the value of the mixer timer setting. Check the value of the dump delay timer.
Bulletin Number Chapter 6: Troubleshooting 71 of 102 Problem Corrective action I can’t calibrate the Scale without an error message. This Is caused by the difference in bits not being large enough. Using the Direct Scale Readout, ex amine current loadcell bits with and without the calibration weight.
Bulletin Number Chapter 7: Appendix 72 of 102 Chapter 7: Appendix 7-1 Warranty Unless otherwise specified, this produc t includes a Standard ONE YEAR PARTS WARRANTY.
Bulletin Number Chapter 7: Appendix 73 of 102 Customer Responsibilities Any sales, use, or other tax incident to the replacement of parts under this warranty is the responsibility of the purchaser.
Bulletin Number Chapter 7: Appendix 74 of 102 Annex B Information The following design information is provided for your reference: 1. No modifications are allowed to this equi pment that could alter the CE compliance 2. Ambient temperature: 40 degrees Celsius – Maximum (104 degrees Fahrenheit) 3.
Bulletin Number Chapter 7: Appendix 75 of 102 7-3 Drawings and Diagrams Final Assembly Figure 53: Typical Final Assembly Parts List # Description 150 900 2500 4000 6000 1 Mixer Assembly A0771677 A0771.
Bulletin Number Chapter 7: Appendix 76 of 102 Mixer Sub-Assembly.
Bulletin Number Chapter 7: Appendix 77 of 102 Figure 54: Typical Mixer Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 FRAME 872.00093.00 872.00094.00 A0770301 872.00224.00 2 FRAME EXTENSION (NOT SHOWN) N/A 872.00225.00 3 TOP PLATE 872.00095.
Bulletin Number Chapter 7: Appendix 78 of 102 Hopper Sub-assembly Figure 55: Typical Hopper Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 3-COMPONENT HOPPER 872.00118.00 A0569131 872.00240.00 1 2-COMPONENT HOPPER 872.00119.00 A0770299 872.00241.
Bulletin Number Chapter 7: Appendix 79 of 102 Hopper R.A.M. (Regrind Auger Metering) Sub-Assembly (Optional) Figure 56: Typical R.A.M. Hopper Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 THROAT 07822-1 2 CLAMP A0548808 3 FEEDER TUBE # 872.
Bulletin Number Chapter 7: Appendix 80 of 102 Hopper Additive Feeder Sub-Assembly (Optional) Figure 57: Typical Additive Feeder Hopper Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 THROAT A0541201 2 MOTOR MOUNT BRACKET A0541229 3 MOTOR – AUGER 51450G 4 THROAT ADAPTER – 2” RISER 872.
Bulletin Number Chapter 7: Appendix 81 of 102 Weigh Hopper Sub-assembly Figure 58: Typical Weigh Hopper Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 WEIGH HOPPER 872.00103.00 872. 00104.00 A0770312 872.00229.00 872.00230.00 2 AIR CYLINDER 245.
Bulletin Number Chapter 7: Appendix 82 of 102 Slide Gate Sub-assembly Figure 59: Typical Slidegate Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 HOUSING (DOUBLE DIAMOND) (#1-4) 872.00114.00 A0770304 872.00524.00 HOUSING (SQUARE / DIAMOND) (#1-4) A0770308 N/A 1 HOUSING (DOUBLE DIAMOND) (#5-6) 872.
Bulletin Number Chapter 7: Appendix 83 of 102 Knife Gate Sub-assembly HD (Optional) Figure 60: Typical Knife Gate (bel ow mixer) Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 BASE FRAME 0.
Bulletin Number Chapter 7: Appendix 84 of 102 Knife Gate Sub-assembly RD (Optional) Figure 61: Typical Knife Gate (floor stand) Assembly Parts List # DESCRIPTION 500 900 2500 4000 6000 1 HOUSING FRAME 872.00297.00 2 GUARD SAFETY COVER 872.00236.00 3 ROD GUIDE 832.
Bulletin Number Chapter 7: Appendix 85 of 102 Control Panel Layout Figure 62: Typical Mitsubishi Controller Main Parts List # Description 150 500 900 2500 4000 6000 1 Mitsubishi PLC FX2N-32MR A0569702 2 Mitsubishi PLC EEPROM A0569703 3 24 vdc Power Supply A0563932 4 Calex Module – Load Cell Amplifier 724.
Bulletin Number Chapter 7: Appendix 86 of 102 7-4 Spare Parts Kits Figure 64: Blender Spare Parts Listing M odel 150 500 900 2500 4000 6000 KIT "A " (Consumabl es) A 0574120 A 0574134 A 0574137 A 0574125 A0574140 A 0574143 Load Cell Assem bl y (wi thout pl ug) # 724.
Bulletin Number Chapter 7: Appendix 87 of 102 7-5 Addendum (Service Supervisor Information) Caution! After all selections are made: Keep p ressing the “Done” key until the unit returns to the Recipe menu.
Bulletin Number Chapter 7: Appendix 88 of 102 Figure 66: Typical Engineering Only Setup Screen Factory Setup Menu Metering Test Screen This screen is useful in both R & D and development purposes when testing the metering performance of each feeder.
Bulletin Number Chapter 7: Appendix 89 of 102 This setting should not be m odified exce pt by the developer except under unusual circumstances. Figure 68: Typical Advanced Weight Options Screen Feed Algorithm Options Screen This screen allows the user to configure how the blender metering algorithm works.
Bulletin Number Chapter 7: Appendix 90 of 102 Mechanical Options Screen This screen allows the user to change the number of hoppers, the predeterm ined gate cycle time, and the mixer bump time for detecting hi gh level.
Bulletin Number Chapter 7: Appendix 91 of 102 Customer Setup Menu Units This screen allows the user to change the ble nder’s unit of measurement. The entire blender can be configured in either Kgs. or Lbs., while the Target vs. Actual data can be configured for either regardless of the blender’s units.
Bulletin Number Chapter 7: Appendix 92 of 102 Alarm Setup This screen allows the user to configure the f eeder type for each feeder; configure whether a feeder will retry during the metering of a batch, and enable or disable the “Out of Material” alarm for any feeder.
Bulletin Number Chapter 7: Appendix 93 of 102 Factory Default Setup Parameters Model Number 150 500 900 25 00 4000 6000 Recipe Entry Mode PER CENTAG E Metering Order Batch Siz e (lbs ) 2.
Bulletin Number Chapter 7: Appendix 94 of 102 Model N umber 150 500 900 2500 4000 6000 Hop1 Initial % of Target 100 Hop2 Initial % of Target 99 Hop3 Initial % of Target 100 Hop4 Initial % of Target 99 Hop5 Initial % of Target 99 Hop6 Initial % of Target 99 Hop7 Initial % of Target 99 Hop8 Initial % of Target 99 Hop1 All ow ed Underfeed (lbs ) 0.
Bulletin Number Chapter 7: Appendix 95 of 102 7-6 Mitsubishi Communications Manual The Mitsubishi blender uses a FX-2N processor that communicates with the outside world using MELSEC FX protocol over Ethernet hardware. It’s Et hernet speed is 10 Mbits/s econd.
Bulletin Number Chapter 7: Appendix 96 of 102 BLENDER ALARMS 1 (R) alarm_number,D1876 (see below for description) 2 (R) hop1_out_of_material,M561 3 (R) hop2_out_of_material,M562 4 (R) hop3_out_of_mate.
Bulletin Number Chapter 7: Appendix 97 of 102 INVENTORY INF O 1 (RW) clear_inventory,M503 (toggle this to clear a ll inventory, you must also reset this bit after completion) 2 (RW) batch_counter,D133.
Bulletin Number Chapter 7: Appendix 98 of 102 RECIPE INFO (THIS IS WHERE YOU RIGHT THE NEW RECIPE TO) 1 (RW) temp_recipe_entry_mode,D1706, SHORT VA LUE (0=percentage mode, 1=parts mode, 2=EZ mode) 2 (R) temp_batch_size_recipe_value,D1234,LONG VALUE (xxx.
Bulletin Number Chapter 7: Appendix 99 of 102 9 (R) recipe_target_total,D1144,LONG VALUE (xxx.xx, the is the total of hop1-hop6 from above, you must manually add this if you chose to skip the blende r.
Bulletin Number Chapter 7: Appendix 100 of 102 Alarm Number Explanation: The alarms are given in individual bits and are reflect ed in the alarm number. The alarm number is only used to drive a pop-up message and will probably not be very useful to you.
Bulletin Number Chapter 7: Appendix 101 of 102 WRITING RECIPE EXPLANA TION To write a recipe you must first write to the “temp r ecipe” value locations above. After this is complete you should read the “accept recipe enabled” and the “recipe error” values.
Bulletin Number Chapter 7: Appendix 102 of 102 7-7 Technical Assistance Parts Department Call Spare Parts Express toll-free 8am-8pm EST (800) 229-2919. OEM quality replacement and spare parts ensure operation at design sp ecifications. Please have the model and serial number of your equipment when you call.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Mitsubishi Electronics 882.00207.00 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Mitsubishi Electronics 882.00207.00 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Mitsubishi Electronics 882.00207.00 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Mitsubishi Electronics 882.00207.00 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Mitsubishi Electronics 882.00207.00, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Mitsubishi Electronics 882.00207.00.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Mitsubishi Electronics 882.00207.00. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Mitsubishi Electronics 882.00207.00 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
