Manuale d’uso / di manutenzione del prodotto UX-G66 del fabbricante JVC
Vai alla pagina of 36
COMP ACT DISC/TUNER CASSETTE DECK For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet.
Caution: Proper V entilation T o av oid risk of electr ic shoc k and fire, and to pre vent damage, locate the appar atus as follows: 1 F ront: No obstructions and open spacing. 2 Sides/ T op/ Back: No obstructions should be placed in the areas shown b y the dimensions below .
G-2 REPRODUCTION OF LABELS IMPORTANT FOR LASER PRODUCTS 1 CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE 2 WARNING LABEL, PLACED INSIDE THE UNIT CLASS 1 LASER PRODUCT 1. CLASS 1 LASER PRODUCT 2. DANGER : Invisible laser radiation when open and interlock failed or defeated.
1 Power sources • When unplugging from the wall outlet, always pull the plug, not the A C power cord . DO NO T handle the A C power cord with wet hands.
2 Contents Introduction .......................................................... 1 About This Manual ............................................................... 1 Precautions ......................................................................
3 Location of the Buttons and Controls XT -UXG66 Compact Disc /T uner AX-UXG66 Stereo Amplifier TD-UXG66 Cassette Deck Display window Front Panels REC BASS 1 2 34 Become familiar with the b uttons and controls on the units.
4 Front Panels AX-UXG66 Stereo Amplifier 1 button and ST ANDBY/ON lamp (11)* 2 MUL TI JOG dial 3 FM/AM b utton (14)* 4 OPEN/CLOSE b utton (13)* 5 Display windo w 6 V OLUME dial (11) 7 A UX b utton (13.
5 VOLUME MD ENTER AUTO PRESET PLAY MODE FM MODE CANCEL DISPLAY /CHARA. BASS SLEEP PANEL OPEN/CLOSE REMOTE CONTROL RM-SUXG6E > < TAPE FM/AM DOWN SET UP AUX 2 4 6 ; 1 a s d f g h j k l / 3 5 8 p 7 9 w q r e t y i u TITTLE/EDIT REPEAT TREBLE DIMMER CLOCK/TIMER CD ACTIVE BASS EX.
6 Unpacking After unpacking, check to be sure that you hav e all the following items. The number in the parentheses indicates the quantity of the pieces supplied. • AM loop antenna (1) • FM antenna (1) • Remote control (1) • Batteries (2) • Speaker cords (2) • External wire (1) If any is missing, consult your dealer immediately .
7 Connecting Antennas Supplied FM antenna 1 Attach the FM antenna to the FM 75 Ω CO AXIAL terminal on the rear panel of XT -UXG66. 2 Extend the FM antenna. 3 Fasten it up in the position which gi ves you the best reception. About the supplied FM antenna The FM antenna supplied with this unit can only be used as temporary measure.
8 RIGHT LEFT SPEAKERS 1 2, 3 Connecting Speakers Y ou can connect the speakers using the speaker cords. 1 Open the speaker terminal. 2 Insert the end of the speaker cord to the terminal. Match the polarity of the speaker terminals: Red (+) to red (+) and black (–) to black (–).
9 Connecting Other Equipments Y ou can connect the following equipments to the system: • Audio equipment — used only as an analog playback device. • Audio equipment with an optical digital input terminal — used as a digital recording device. When you connect and use these equipments, refer also to the manuals supplied with them.
10 Basic Settings Before operating the system any further , set the clock b uilt in this system f irst, then some other basic settings. Setting the Clock Y ou can set the clock using the remote control whether the system is turned on or turned of f (i.
11 Common Operations Here are basic and common things that apply to all the operations of UX-G66 system. T urning On the Power and Selecting the Sources When you press a play b utton for example, like FM/AM, CD 6 (play/pause), or T APE 23 (playback), the system automatically turns on and ST ANDBY/ON lamp lights green.
12 • When using the remote control, press V OLUME + button to increase the volume le v el or press VOLUME – b utton to decrease it. The volume le vel (from 0 to 50) a ppears in the display windo w as follows: For pri vate listening Connect a pair of headphones to the PHONES jack.
13 Operating the Sliding Panel Y ou can use the sliding panel to enable advanced operations features provided for UX-G66 micro component system. • Press OPEN/CLOSE button on the front panel (or P ANEL OPEN/CLOSE button on the remote control). The sliding panel opens to uncov er the inner buttons behind the panel for further operations.
14 English Y ou can tune in FM and AM (MW/L W) stations manually ,automatically , and use the preset station feature. T uning in a Station 1 Press FM/AM b utton. The system automatically turns on and tunes in the last tuned station (either FM or AM—MW/L W).
15 English T o preset stations automatically — Auto Preset Y ou can automa tically preset 30 FM, 15 AM (MW/L W) stations. Preset numbers will be allocated as stations are found, starting from the lo w est frequency and mo ving up to the higher frequency .
16 English • DO NO T try to open or close the CD tray by hands as it will be damaged. • DO NO T place any foreign matters. • DO NO T prev ent the tray from opening and closing, because it may results damages on the unit. 3 Press 0 (open/close) b utton again.
17 English T o go to another track Before or during playback, press 4 / ¢ b utton repeatedly: Press ¢ b utton: Skips to the beginning of the ne xt and succeeding tracks. Press 4 b utton: Goes back to the beginning of the current and pre vious tracks.
18 English 4 Pr ess SET button to program the track number . T rac k number Program number Here the track number 2 on the CD is stored into a program number 1, and shortly after that the total playbac.
19 English Repeating T racks — Repeat Play Y ou can have the entire disc, the programed tr acks, or the individual track repeat as man y times as you like. 1 Place a CD. If the current playing source is not the CD, press 6 (play/pause) button on the CD unit, then 7 (stop) button before going to the next step.
20 • DO NO T try to open or close the tape tray by hands as it will be damaged. • DO NO T place any foreign matters. • DO NO T prev ent the tray from opening and closing, because it may results damages on the unit. 3 Press 0 (open/close) b utton again to close the tray .
21 T o skip for ward to the next music Press the button same as the tape direction indicator as follows: 3 ] Press ¢ b utton. 2 ] Press 4 button. During Music Scan progressed, the tape direction indicator starts blinking rhythmically . Repeating Music Scan feature made easy searching a desired program on a tape one after another .
22 T wo types of cassette tapes can be recorded onto, including normal (T ype I), and High position (T ype II) tapes. These types are identif ied automatically by the cassette deck unit and the recording le vel is also corrected automatically . Neither volume le vel nor sound effects during playback does af fect to the recording.
23 • Dolby B NR Press DOLBY B NR button before recording to reduce frequency response noise. When the tape is played back later , also press the button with its lamp lit. • BEA T CUT on AM (MW/L W) When recording AM broadcast, beats noise may be heard.
24 Synchronized Recording from a CD CD application on UX-G66 system can be recorded with a simple, one-touch operation. 1 Place a recordable tape and a sour ce CD into each tray . • T o record using Dolby B NR, press the DOLBY B NR button before recording so that its lamp near the button lights orange.
25 • Each time you press the button, the timer mode changes as follo ws: 2 Rotate MUL TI JOG dial ( < / > button on the r emote control also a vailable) to select the hour of the timer - on time, then press SET b utton.
26 2 Press SET b utton to call the previous settings f or next timer recording . The REC timer indicator lights, and the setting items appear one after another in the display window . • T o erase the recor ding timer, press CANCEL b utton in this step.
27 4 Rotate MUL TI JOG dial ( < / > b utton on the remote control also a vailable) to select the hour of the timer - off time, then press SET b utton. 5 Rotate MUL TI JOG dial ( < / > b utton on the remote control also a vailable) to select the minute of the timer -off time, then press SET b utton.
28 Timer Priority Since each timer can be set separately , you may w onder what happens if the setting for these timers overlaps. Here are the priorities for each timer . • Recording Timer has priority over Daily Timer and Sleep Timer . If Daily T imer is set to come on while Recording T imer is operating, Daily T imer will not come on at all.
29 General Notes In general, you will hav e the best performance by keeping your CDs, cassette tapes and the mechanism clean. • Store CDs and cassette tapes in their cases, and keep them in cabinets or on shelves. • K eep the CD disc tray , and the cassette tapes tray closed when not in use.
30 T ypes of Cassette T apes This cassette deck unit incorporates an Automatic T ape Detection function. This mechanism uses the tape-type detection holes to distinguishes which type of tape was inserted, and sets the bias and equalizer to the optimum settings for that tape automatically .
31 T roubleshooting If you are having a problem with your system, check this list for a possib le solution before calling for service. If you cannot solve the problem from the hints gi ven here, or the units has been physically damaged, call a qualif ied person, such as your dealer , for service.
32 Specifications Stereo Amplifier AX-UXG66 Output power: 48 W (24 W + 24 W) at 6 Ω (Max.) 42 W (21 W + 21 W) at 6 Ω (10% THD) Load impedance: 6 Ω (6 Ω to 16 Ω allo wance) Audio output lev el/Impedance (at 1 kHz): Sub W oofer 800 mV/440 Ω Po wer requirement: A C 240 V , 50 Hz Po wer consumption: 63 W (a t operation) 2.
0201JTMMDWJSC EN VICTOR COMP ANY OF JAP AN , LIMITED cover[A]f 12/11/00, 11:36 AM 2.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il JVC UX-G66 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del JVC UX-G66 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso JVC UX-G66 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul JVC UX-G66 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il JVC UX-G66, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del JVC UX-G66.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il JVC UX-G66. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo JVC UX-G66 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
