Manuale d’uso / di manutenzione del prodotto RX-5060B del fabbricante JVC
Vai alla pagina of 40
LVT1507-001A [J] RX-5060B A UDIO/VIDEO CONTR OL RECEIVER INSTR UCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference. Model No.
G-1 CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. ATTENTION Afin d’éviter tout risque d’électrocution, d’incendie, etc.: 1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.
1 T able of Contents Adjusting Sound ........................................ 21 Basic Adjustment Items ............................................................ 21 Basic Procedure ...................................................................
2 Front Panel Par ts Identification STANDBY STANDBY/ON PHONES SURROUND DSP SPEAKERS ON/OFF SUBWOOFER OUT FM MODE MEMORY ON/OFF FM/AM TUNING SURROUND/DSP OFF DIMMER MASTER VOLUME INPUT DIGITAL RX—603.
3 Remote Control AUDIO TV/CA TV VCR DV D TEST EFFECT MENU ENTER LEVEL RETURN SURROUND/ DSP CD - DISC SLEEP REC P AUSE FM MODE SURROUND DSP DIMMER TV/VIDEO MUTING OFF VCR CH TV/CA TV CH VOLUME SURR R S.
4 Notes: • Supplied batteries are for the initial setup . Replace f or continued use. • After replacing the batteries, set the manuf acturers’ codes again (see pages 31 and 32).
5 Connecting the Speakers and Subwoofer Y ou can connect fi ve speakers (a pair of front speakers, a center speaker , and a pair of surround speakers) and a subwoofer . CA UTIONS: • Use only the speakers of the SPEAKER IMPED ANCE indicated by the speak er ter minals.
6 Connecting Audio/V ideo Components When connecting individual components, refer also to the manuals supplied with them. Analog Connections Audio component connections Use the cables with RCA pin plugs (not supplied). • Connect the white plug to the audio left jack, and the red plug to the audio right jack.
7 DVD player Å To composite video output ı To left/right front channel audio output (or to audio-mixed output if necessary) Note: T o enjoy Dolb y Digital and DTS multi-channel software (including Dual Mono software), connect the D VD pla yer through the digital input/ output terminals.
8 DIGIT AL 1(DVD) DIGIT AL 2(CD) DIGIT AL IN Digital Connections By connecting the recei ver and the source component through the digital terminals, sound reproduction quality will be much impro ved. In addition, you can enjoy multi-channel reproduction and some other con venient functions.
9 Basic Operations The following operations are commonly used when you play any sound sources. Operations hereafter will be explained using the b uttons on the front panel. Y ou can also use the buttons on the remote control for the same functions if they ha ve the same and similar names/marks.
10 Selecting different sour ces for picture and sound While watching pictures from a video source, you can listen to sound of an audio source. • Once you hav e selected a video source, pictures of the selected source are sent to the TV until you select another video source.
11 Listening with headphones: Y ou can enjoy not only stereo software b ut also multi- channel software through the headphones. (Sounds are down-mix ed to the front channels while playing multi-channel software.) 1 Press SPEAKERS ON/OFF to deactiv ate the speakers.
12 When playing software encoded with Dolby Digital or DTS, the following symptoms ma y occur: • Sound does not come out at the beginning of playback. • Noise comes out while searching for or skipping chapters or tracks. In this case, press INPUT DIGIT AL repeatedly to select “DOLBY DIGIT AL” or “DTS SURR OUND.
13 The follo wing basic operations are possible only using the remote contr ol. Muting the Sound Press MUTING to mute the sound thr ough all speakers and headphones connected. “MUTING” appears on the display and the volume turns of f (the V OLUME indicator and its lev el indication go off).
14 Using Preset T uning Once a station is assigned to a channel number , the station can be quickly tuned in. Y ou can preset up to 30 FM and 15 AM stations. T o stor e the pr eset stations Bef ore you start, r emember ... There is a time limit in doing the following ste ps.
15 T o tune in a pr eset station On the front panel: 1 Press FM or AM to select the band. 2 Press FM/AM PRESET 5 or ∞ until you f ind the channel y ou want. • Pressing FM/AM PRESET 5 increases the number . • Pressing FM/AM PRESET ∞ decreases the number .
16 Quick Speaker Setup Quick Speaker Setup helps you to easily and quickly register the speaker size and speaker distance according to your listening room to create the best possible surround ef fect. • Y ou can also r egister each speak er’ s information manually .
17 Basic Setting Items On the following pa ges, you can adjust the following items: • Y ou can onl y select the items currently a vailable. For details, see the explanation of each item. Items T o do See page SUBWOOFER * Register your subw oofer. 18 FRNT SPEAKERS * Register your front speak er size .
18 ¶ Speaker distance — FRONT L DIST , FRONT R DIST , CENTER DIST , SURR L DIST , SURR R DIST Set the distance from the listening point within the r ange of 0.3 m (1 ft) to 9.0 m (30 ft), in 0.3 m (1 ft) interv als. • When shipped from the factory , distance for each speaker is set to “3.
19 ¶ Cr ossover fr equency —CROSSOVER Y ou can select the crossover frequency f or the small speakers used. The signals belo w the preset frequency le vel will be sent to and be reproduced by the subwoofer (or by “LARGE” speak ers when “SUBWOOFER” is set to “SUBWOOFER NO”).
20 Setting the Digital Input T er minals When you use the digital input terminals, register which components you hav e connected to the digital input terminals. ¶ Digital Input ter minal —DIGIT AL IN Set the components connected to the digital terminals.
21 Adjusting Sound Y ou can make sound adjustment to your preference after completing basic settings. Basic Procedur e Bef ore you start, r emember ... There is a time limit in doing the follo wing steps. If the setting is canceled before you f inish, start from step 1 again.
22 Y ou can also use the remote control for adjusting the speaker output le vel using the test tone. • Y ou can also adjust the effect le vel for D AP modes and Mono F ilm. T o adjust the speaker output le vel: 1 Press SOUND . The number buttons are acti va ted for sound adjustments.
23 Using the Sur r ound Modes This unit activates a variety of Surround modes automatically . The basic settings and adjustments stored (see pages 16 to 22) are applied automatically .
24 DTS * 2 DTS is another digital signal compression method, dev eloped by Digital Theater Systems, Inc., and enables multi-channel encoding and decoding (1ch up to 6.1ch). • When DTS signal is detected through the digital input, the indicator lights up on the display .
25 • F or DTS multi-channel digital software (except 2-channel and Dual Mono software), incoming signals are automatically detected and “DTS SURR OUND” is acti vated. Note: When the Dolby Digital or DTS multi-channel digital signal stops coming in, “PLII MO VIE” will be activ ated.
26 : Suitable for audio sources : Suitable for video sources Using the DSP Modes This unit activates a variety of DSP modes automatically . The basic settings and adjustments stored (see pages 16 to 22) are applied automatically . Early reflections Reflections from behind Reproducing the Sound Field The sound heard in a concert hall, club, etc.
27 DSP All Channel Stereo This mode can reproduce a larger stereo sound f ield using all the connected (and acti vated) speakers. • If the surround speakers ar e set to “NONE, ” you cannot select “ ALL CH STEREO.
28 COMPU LINK Remote Contr ol System The COMPU LINK remote control system allows you to operate JVC’ s audio components through the remote sensor on the receiver .
29 Operating JVC’ s Audio/V ideo Components Y ou can operate JVC’s audio and video components with this r eceiver’s remote contr ol, since control signals for JVC’s components are preset in the remote control. T uner Y ou can always perform the follo wing operations: FM/AM: Alternate between FM and AM.
30 Operating Video Components IMPORT ANT : T o operate JVC’ s video components using the supplied remote control: • Some JVC’ s VCRs can accept two types of the control signals— remote code “ A” and “B. ” Before using this remote control, make sure that the remote control code of the target VCR is set to code “ A.
31 Operating Other Manufactur ers’ V ideo Equipment This remote control supplied for the receiver can transmit control signals for other manufacturers’ TVs, CA TV conver ters, VCRs and DVD players. When operating the other manufacturers’ components, refer also to the manuals supplied with them.
32 T o change the transmittable signals for operating another manufacturer’s DVD player 1 Press and hold ST ANDBY/ON DV D . 2 Press D VD. 3 Enter a manufactur er’s code using b uttons 1 – 9, and 0. Manufacturer Codes JVC 01* Panasonic 02 Philips 04 Pioneer 03 Sony 05 T oshiba 06 Y amaha 07 * “01” is the initial setting.
33 T r oubleshooting Use this char t to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’ s ser vice center . SOLUTION Plug the power cord into an AC outlet. Check speaker wiring and reconnect if necessary.
34 Specifications Amplifier Output Po w er Front channels: 100 W per channel, min. RMS, dri ven into 8 Ω , at 1 kHz with no more than 10% total harmonic distortion. Center channel: 100 W , min. RMS, driv en into 8 Ω , at 1 kHz with no more than 10% total harmonic distortion.
35 FM tuner (IHF) T uning Range: 87.5 MHz to 108.0 MHz Usable Sensiti vity Monaural: 12.8 dBf (1.2 µV/75 Ω ) 50 dB Quieting Sensiti vity Monaural: 16.
Warr&CS_RX-5060B[J].p65 05.11.29, 14:16 36.
Warr&CS_RX-5060B[J].p65 05.11.29, 14:16 37.
1205YHMMDWJEIN EN © 2005 Victor Company of Japan, Limited AUDIO/VIDEO CONTROL RECEIVER RX-5060B Cover_RX-5060B[J].p65 05.11.28, 19:58 2.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il JVC RX-5060B è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del JVC RX-5060B - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso JVC RX-5060B imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul JVC RX-5060B ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il JVC RX-5060B, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del JVC RX-5060B.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il JVC RX-5060B. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo JVC RX-5060B insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
