Manuale d’uso / di manutenzione del prodotto CS 2121 EL del fabbricante Jonsered
Vai alla pagina of 16
GB Operator’ s Manual 115 02 33-26.
ENGLISH 2 SYMBOLS USED IN OPERA T OR’S MANU AL: Do not use a coiled extension cord. Minimum wire cross-section: 1,5 mm ² Maximum cable length: 30 m V oltage: 230 V CAUTION! Chain saws are danger ous! Careless or impr oper use can result in sever e or fatal injury .
ENGLISH 3 Symbols 2 Important! Read before using chain saw 2 Contents 3 EC declaration of conformity 3 T echnical speci fi cations 4 Chain saw parts 5 Safe use 5 Starting and stopping 7 Daily inspect.
ENGLISH 4 Motor 1700 2000 Rated voltage V AC 220-240 230 Rated output W 1700 2000 Frequency Hz 50/60 50 Slip clutch Y es Y es Electronic start contr ol - Y es Electronic speed contr ol - Y es Electron.
ENGLISH 5 1. Rear handle 2. Power trigger lockout 3. Front handle 4. Serial No. plate 5. Chain tensioner 6. Chain oil reservoir 7. Chain oil level 8. V entilation slots 9. Power cable 10. Power trigger 11. Chain 12. Guide bar 13. Chain brake release button 14.
ENGLISH 6 • See to it that others keep their distance as long as the chain is in motion. Keep onlookers, children and animals away from the work ar ea. Do not let inexperienced persons handle the chainsaw or power cable. • Keep work ar ea clear and well-lighted.
ENGLISH 7 D AIL Y INSPECTION AND MAINTENANCE CAUTION! Always disconnect the power before cleaning or performing maintenance. Here ar e a few general instructions for maintaining your hand- saw . If you are in doubt on any of these points, contact your service dealer .
ENGLISH 8 • T ake extreme car e when cutting with the top chain (on the underside of a log). The force of the chain action pushes the saw backwards, and if the operator does not maintain fi rm control, the kickback danger zone may move far enough back into the kerf to produce a kickback.
ENGLISH 9 • The chain brake may be activated manually or by the force of inertia depending on the strength of the kickback and the position of the saw in relation to the object which made contact with the kickback danger zone.
ENGLISH 10 6. Replace the chain drive cover and screw the mounting nut hand tight. 7. T ension the chain by screwing the tensioning screw clockwise using the screwdriver tip on the combination tool. 8. Tighten chain fi rmly but not so hard that it does not turn easily by hand force.
ENGLISH 11 • Ensure that the cutter teeth are always correctly sharpened! Follow our instructions and use the recommended fi ling guide. A chain which is damaged or improperly maintained incr eases the risk of accident. • Maintain the correct depth-gauge height.
ENGLISH 12 Checking chain wear • Inspect chain every day for: - Visible cracks in rivets or links - Stiffness - Abnormal wear in rivets or links - Min. 3 mm (1/8”) horizontal cutter length - Any deviation on any of these points indicates a worn chain which must be discarded - Check the guide bar’ s oil passage and clean if necessary .
ENGLISH 13 See «T echnical Specifi cations» for the details which apply to your chain. It is very diffi cult to fi le a chain saw correctly with- out the proper aids. W e recommend the use of a fi le guide to ensure maximum cutting effi ciency with the least tendency to kickback.
ENGLISH 14 • Cutting a log supported at one end. The log is more than likely to splinter if cut straight through fr om the top down. - Make an initial cut from below (appr ox. 1/3 of the diameter) - Finish the cut from above. • Cutting a log supported at both ends.
ENGLISH 15 Danger zone A danger zone surrounds the tr ee to a distance of 2 1/2 times the height of the tree. See to it that no one is standing within this zone while you are felling the tree. Felling direction When felling a tree, one always aims to place it wher e neither objects nor diffi cult terrain will hamper limbing and cutting.
´®z+R7@¶6T¨ ´®z+R7@¶6T¨ 115 02 33-26 www .jonsered.com T røskenveien 36 P .O.B. 10 N - 1708 Sarpsbor g Norway 2006W11.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Jonsered CS 2121 EL è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Jonsered CS 2121 EL - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Jonsered CS 2121 EL imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Jonsered CS 2121 EL ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Jonsered CS 2121 EL, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Jonsered CS 2121 EL.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Jonsered CS 2121 EL. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Jonsered CS 2121 EL insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
