Manuale d’uso / di manutenzione del prodotto OCMK01 del fabbricante Invacare
Vai alla pagina of 16
On Chair Mounting Kit Assembly , Installation and Operating Instructions Model Nos. OCMK01 and OCMK78 SA VE THESE INSTRUCTIONS NOTE: Check all parts for shipping damage.
2 INSTALLATION OF THE ON CHAIR MOUNTING KIT BACK MOUNTING HARDWARE (FIGURE 1) NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction sheet. NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2 twist release clamps.
3 Twist Release Clamps. DETAIL "B" Mark FRONT OF WHEELCHAIR Fixed Release Clamp Internal Threaded Mounting Screw Washer Mounting Screw DETAIL "A" Upper J Brackets (Top Edge) Lower .
4 INSTALLING THE BACK L BRACKETS (FIGURE 2) NOTE: When mounting the L brackets to the wood backed ContourU cushion the L brackets may be reversed to allow for greater seat depth adjustments as shown in DETAIL A of FIGURE 2.
5 INSTALLING THE BACK J BRACKETS (FIGURE 3) 1. Position the ContourU back between the back canes to determine the approximate mounting position of the J brackets to obtain the desired depth. 2. Align two (2) of four (4) mounting holes of the J bracket with two (2) of five (5) mounting holes on the L bracket as shown in FIGURE 3.
6 INSTALLING/REMOVING THE CONTOUR U SEATING SYSTEM BACK (FIGURE 4) Installing 1. Ensure that the twist release clamps are in the OPEN position as shown in DETAIL A of FIGURE 4. 2. Position the two (2) lower J brackets securely into the two (2) fixed release clamps as shown in FIGURE 4.
7 ADJUSTING THE CONTOUR U BACK DEPTH (FIGURE 5) NOTE: There are six (6) depth adjustments avail- able on the ContourU with a pan back. NOTE: There are twelve (12) depth adjustments available on the ContourU with a wood back.
8 ADJUSTING THE CONTOUR U SEATING SYSTEM BACK ANGLE (FIGURE 6) NOTE: Before performing this procedure all four (4) J brackets must be adjusted to the same depth. Refer to ADJUSTING THE CONT OUR U SEA TING SYSTEM BACK DEPTH in this instruction sheet. NOTE: The back to seat angle is adjusted by repositioning the top and/or the bottom J brackets.
9 INSTALLATION OF ON CHAIR MOUNTING KIT SEAT MOUNTING HARDWARE (FIGURE 7) NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction sheet. NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2) twist release clamps.
10 Twist Release Clamps. DETAIL "B" Mark Fixed Release Clamp Internal Threaded Mounting Screw Washer Mounting Screw DETAIL "A" Front J Brackets (Front Edge) Rear J Brackets (Rear E.
11 INSTALLING THE SEAT L BRACKETS (FIGURE 8) NOTE: When mounting the L brackets to the wood backed ContourU seat the L brackets may be reversed to allow for a wider range of seat height adjustments and shown in DETAIL A of FIGURE 8.
12 INSTALLING THE SEAT J BRACKETS (FIGURE 9) 1. Position the ContourU seat between the seat rails to determine the approximate mounting position of the J brackets to ensure the appropriate height setting. 2. Align two (2) of four (4) mounting holes of the J bracket with two (2) of five (5) mounting holes on the L bracket as shown in FIGURE 9.
13 INSTALLING/REMOVING THE CONTOUR U SEATING SYSTEM SEAT (FIGURE 10) Installing 1. Ensure that the twist release clamps are in the OPEN position as shown in DETAIL A of FIGURE 10. 2. Position the rear J brackets securely into the fixed release clamps as shown in FIGURE 10.
14 ADJUSTING THE CONTOUR U SEAT HEIGHT (FIGURE 11) NOTE: There are six (6) height adjustments avail- able on the ContourU seat with a seat pan. NOTE: There are twelve (12) height adjustments available on the ContourU seat with a wood back.
15 ADJUSTING THE CONTOUR U SEATING SYSTEM SEAT ANGLE (FIGURE 12) NOTE: Before performing this procedure all four (4) J brackets must be adjusted to the same height. Refer to ADJUSTING THE CONTOUR U SEAT HEIGHT in this instruction sheet. NOTE: The seat angle is adjusted by repositioning the front and/or the rear J brackets.
Invacare Corporation www.invacare.com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare is a registered trademark of Elyria, Ohio USA Mississauga Ontario Invacare Corporation. 44036-2125 L4Z4G4 Canada Yes, you can. is a trademark of Invacare 800-333-6900 800-668-5324 Corporation.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Invacare OCMK01 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Invacare OCMK01 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Invacare OCMK01 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Invacare OCMK01 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Invacare OCMK01, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Invacare OCMK01.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Invacare OCMK01. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Invacare OCMK01 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
