Manuale d’uso / di manutenzione del prodotto SRC-10H del fabbricante Hoshizaki
Vai alla pagina of 25
Hoshizaki “A Superior Degree of Reliability” www .hoshizaki.com Model FS-1001MLH/-C Modular Flaker Serenity Series Including Condensing Unit Model SRC-10H Hoshizaki America, Inc.
2 HOSHIZAKI AMERICA, INC. 618 Highway 74 South Peachtree City, GA 30269 Attn: HOSHIZAKI Technical Support Department Phone: 1-800-233-1940 Technical Service (770) 487-2331 Fax: 1-800-843-1056 (770) 487-3360 Web Site: www.
3 CONTENTS I. Specifications .............................................................................................................. ...... 4 1. Nameplate Rating ..................................................................................
4 I. Specifications 1. Nameplate Rating [a] FS-1001MLH, FS-1001MLH-C See the nameplate for electrical and refrigeration specifications. This nameplate is located on the left-hand side of the rear panel.
5 [b] Condensing Unit Model SRC-10H We reserve the right to make changes in specifications and design without prior notice. See the nameplate for electrical and refrigeration specifications. This nameplate is located on the left-hand side of the right-side panel.
6 2. Dimensions/Connections [a] FS-1001MLH, FS-1001MLH-C Unit = inches [mm].
7 [b] With Storage Bin Unit = inches [mm.].
8 [c] Condensing Unit Model SRC-10H.
9 Fig. 1 II. Installation and Operating Instructions 1. Checks Before Installation W ARNING Remove shipping carton, tape(s) and packing. If packing material is left in the icemaker, it will not work properly. IMPOR T ANT Ensure all components, fasteners and thumbscrews are securely in place.
10 Fig. 2 3. Location W ARNING This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F; Normal operating water temperature should be within +45°F to +90°F. Operation of the icemaker for extended periods outside of these normal temperature ranges may affect production capacity.
11 5. Electrical Connection This icemaker must have an independent power supply or receptacle of proper capacity. See the nameplate. 6. Installation of Remote Condensing Unit [a] Checks Before Installation 1) Unpack and remove shipping carton, tape(s) and packing.
12 [c] Setup 1) Secure the legs to the condensing unit with eight M8 x 16 mm hexagon bolts and M8 nuts as shown in the illustration. See Fig. 4. Note: Locate the legs symmetrically. 2) The legs have eight mounting holes. Secure the legs with eight bolts (not included).
13 [d] Electrical Connection W ARNING 1. This condensing unit must have a separate power supply. See the nameplate. 2. This condensing unit requires a ground that meets the national and local electrical code requirements.
14 7. W ater Supply and Drain Connections See Fig. 7 • External filters or strainers may be required depending on the water quality. • Water supply inlet is 1/2" female pipe thread (FPT). • A water supply line shut-off valve and drain valve should be installed.
15 8. Timer Setting See Fig. 8 The ice machine is equipped with an adjustable timer in the control box. It controls the amount of time the machine waits before shutting down after ice is detected by the bin control; the timer thereby controls the ice level in the bin or dispenser.
16 9. Final Checklist 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F and the water temperature within +45°F to +90°F all year around.
17 10. Startup IMPORT ANT 1. The condensing unit is shipped with the contacts of the secondary low pressure switch open. Once power is supplied to the condensing unit, wait at least 4 hours before starting the unit. This will allow the system to settle and refrigerant to evaporate from oil in the compressor.
18 11. Preparing the Icemaker for Long Storage See Fig. 9 W ARNING When shutting off the icemaker for an extended time, drain out all water from the water line and remove the ice from the storage bin.
19 III. Cleaning and Maintenance IMPORT ANT Ensure all components, fasteners and thumbscrews are securely in place after any maintenance or cleaning is done to the equipment. 1. Cleaning and Sanitizing Instructions W ARNING 1. HOSHIZAKI recommends cleaning this unit at least once a year.
20 [b] Cleaning Procedure The cleaning process will remove lime deposits from the water system. 1) Remove the front panel and top panel, then turn off the power supply. 2) Close the water supply line shut-off valve. 3) Remove all ice from the storage bin.
21 [c] Sanitizing Solution Dilute 2.5 fl. oz. (74 ml or 5 tbs) of IMS-II Sanitizer or a 5.25% sodium hypochlorite solution (chlorine bleach) with 5 gallons (19 l) of warm water. IMPOR T ANT For safety and maximum effectiveness, use the solution immediately after dilution.
22 11) Disassemble the bin control assembly by removing the two snap pins, shaft and actuator. 12) Soak the removed parts in .25 gallons (1 l) of sanitizing solution for 10 minutes then wipe them down. 13) Rinse the parts thoroughly. IMPOR T ANT If the solution is left on these parts, they will rust.
23 11) Remove the front panel. 12) Move the flush switch to the “FLUSH” position to drain the remainder of the solution. 13) After the solution is drained, move the flush switch to the “ICE” position. 14) Replace the front panel in its correct position.
24 2. Maintenance Instructions IMPORT ANT 1. This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker.
25 HO S HIZAKI AMERICA, INC. 61 8 Hwy . 74 S ., Pe a chtree City , GA 3 0269 U S A TEL (770) 4 8 7-2 33 1 F AX (770) 4 8 7- 33 60 www .ho s hiz a ki.com 91A2PB10B.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hoshizaki SRC-10H è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hoshizaki SRC-10H - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hoshizaki SRC-10H imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hoshizaki SRC-10H ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hoshizaki SRC-10H, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hoshizaki SRC-10H.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hoshizaki SRC-10H. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hoshizaki SRC-10H insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
