Manuale d’uso / di manutenzione del prodotto DB-200H del fabbricante Hoshizaki
Vai alla pagina of 19
™ INSTRUCTION MANUAL ISSUED: JUNE 5, 2001 DB-200H ICE DISPENSING BIN R eliability is a beautiful thing TM REVISED: DEC. 10, 2003.
2 IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT Only qualified service technicians should attempt to install, service or maintain this ice dispenser. No installation, service or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual.
3 • Please review this manual. It should be read carefully before the ice dispenser is installed and operated. Only qualified service technicians should install, service and maintain the ice dispenser. This manual should be made available to the technician prior to installation, maintenance or service.
4 We reserve the right to make changes in specifications and design without prior notice. See NAMEPLATE for electrical specifications. The nameplate is located on the upper part of the Right Side Panel. I. SPECIFICATIONS I. SPECIFICATIONS I. SPECIFICATIONS I.
5 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS [a] with KM-280M_ or KM-500M_ [a] with KM-280M_ or KM-500M_ [a] with.
6 [b] with KM-630M [b] with KM-630M [b] with KM-630M [b] with KM-630M [b] with KM-630M.
7 [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_,.
8 II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS 1. CHECKS BEFORE INSTALLATION 1.
9 WARNING WARNING WARNING WARNING WARNING This ice dispensing bin is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F. To the icemaker, water temperature should be within +45°F to +90°F. Extended periods of operation at temperatures outside of these limitations may cause unsatisfactory results.
10 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. CAUTION CAUTION CAUTION CAUTION CAUTION It is especially important that the icemaker/ice dispensing bin is leveled in both left-to-right and front-to-rear directions.
11 Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1 *Note: With KML models, Top Panels are not necessary..
12 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION WARNING WARNING WARNING WARNING WARNING 1. Electrical connection must be made in accordance with the instructions on a “WARNING” tag, provided with the pig tail leads in the Junction Box.
13 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 1. A drain outlet, 3/4" FPT, is located at the rear of the ice dispensing bin.
14 Fig. 4 Drain Connection Fig. 4 Drain Connection Fig. 4 Drain Connection Fig. 4 Drain Connection Fig. 4 Drain Connection.
15 7. START UP 7. START UP 7. START UP 7. START UP 7. START UP 1) Start up the icemaker. See the “START UP” instructions on the icemaker. 2) Allow at least three (3) cycles of ice production, and then place a proper container in the ice station. 3) Push the ice dispensing switch to dispense ice cubes.
16 III. CLEANING AND MAINTENANCE INSTRUCTIONS III. CLEANING AND MAINTENANCE INSTRUCTIONS III. CLEANING AND MAINTENANCE INSTRUCTIONS III. CLEANING AND MAINTENANCE INSTRUCTIONS III.
17 Fig. 5 Fig. 5 Fig. 5 Fig. 5 Fig. 5 Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Agitator Agitator Agitator Agitator Agitator Spout of the Spout of the S.
18 7) Scrub the Shutter Assembly and Spout—after removing them—using the cleaning solution of item 6. See Fig. 5. a) Remove the Snap Pin fitted to the Shutter Shaft and shift the Shaft to the left. Then the Shutter Assembly can be removed from the bin.
19 91A4JB10C HOSHIZAKI HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hoshizaki DB-200H è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hoshizaki DB-200H - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hoshizaki DB-200H imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hoshizaki DB-200H ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hoshizaki DB-200H, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hoshizaki DB-200H.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hoshizaki DB-200H. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hoshizaki DB-200H insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
