Manuale d’uso / di manutenzione del prodotto Holder 12 del fabbricante Hobie
Vai alla pagina of 14
I, ': 1_(, 1 , - !." I!_' : ';..' HOLDER@ 12 - ASSEMBI~~ = '~ :" ' ".
A ;. - Introduction Welcome to the Holder@ family of sailors. Thanks for joining us. By purchasing the Holder@ 12, you are treating yourself to the ultimate in sailing enjoyment. Even if you have long experience with sailboats, please read this manual thoroughly.
HOLDER 12@ Terminology ~ .. MAST WINDOW OUTHAUL REAR PIN DDWNHAUL BOOM VANG BECKET BLOCK BOOM BLOCKS VANG LINE TILLER EXTEN TRAVELE MAIN SHEET VANG ADJUSTER CLEAT HULL DAGGERBOARD . '£ WARNING Before starting assembly, be sure the area in i which you plan to work is free from overhead power lines.
1) Hull 12) Sail 26) Warranty Card, Manual 2) Pad Eye with Block 13) Battens 27) Tiller Extension 3) Mast Tube 14) Daggerboard 28) Hull Drain Plug 4) Jam Cleat 15) Rudder Assembly 29) Cockpit Drain Hole ! 5) Upper Mast Comptip@ 16) Mainsheet (5/16" x 35) 30) Gudgeons ~,~ 6) Lower Mast 17) Halyard Line (1/4" x 34) 31) Hiking Straps ~.
ASSEMBLY INSTRUCTIONS I. The Plugs II. Traveler Assembly The larger drain plug (part #25) is used to Figure 3 shows an example of a completed drain the cockpit of the boat. Insert the large traveler line and block assembly. To assemble t drain plug from the inside of the HOLDER@ 12 the traveler, first find the traveler block set.
III. Mast and Sail Assembly A. Standard and Special Edition The mast is in two sections (part #'s 5, 6). The bottom section displays the warnings against sailing and assembling near overhead t wires and power lines. Before raising the mast, check again that you are in a safe area and always remember this warning.
(Figure 9). Place the sail in the cockpit and connect the zipper by wrapping the luff sleeve around the mast. Fold the webbing around to th~.velcro@~tt~chmeD.tp()int (Figure 10). t. . Fig. 9 Fig. 10 Make sure the halyard is on the inside of the luff sleeve.
IV. Boom Assembly V. Outhaul, Downhaul and . . Vang Assembly The HOLDER@ 12 boom (part #9) IS sImple to use, yet it is one of the most advanced designs Locate the outhaul line (part #18) and the available on a sailboat of this size. To connect downhaul line (part #20).
VI. Mainsheet Assembly Locate mainsheet (part #16). Take one end of the mainsheet and tie it to the small block hanging at the rear of the boom with a bowline (Figure 18). Run the free end through the large r block of the traveler block set and then back up to and through the .
VII. Rudder and DaggerboardSpecial Notes To attach the rudder assembly (part #15) to Using the Kick-up Rudder the boat, align the pins on the rudder with the The kick-up rudder on the HOLDER@ 12 fittings (~art ~30) on the transom. Make sure permits the rudder to do all of the hard work by - t~at the tiller IS placed ~nderneath the tr~ve.
VIII. Basic Sailing: Righting the Boat . . '. If you tip over, stay with the boat (it won't Safe a!1d sane guldehne.s for the begInner, an sink and is easy to right).) It's not necessary, easy review for the experIenced. but the boat is easier to right when the mast is .
IX. Trailering B. Appearance In addition to following all the instructions It's very easy to keep your new HOLDER@ 12 included with your trailer and obeying the rele- fresh-looking. Just follow these minor steps. vant state laws concerning trailering boats, several safety tips should be included in your 1.
Knots to Use .. ., FIGURE 8 * KNOT AT END OF LINE DDUBLE HITCH KNOT FIGURE 8 KNOT BOWLINE KNOT HALYARO KNOT 1. 2. ""' ~ ~ 1~--- -"" r :::-- :.:A4 I ~/ T CLEATING OFF A LINE Basic Sailing THIS AREA CANNOT BE SAILED ~ Iff Q ~ ~ t't()~~ WIND l<~~ V () ?j WIND [ ~ Cia "'ift' ~~«.
Remember Watch for overhead wires whenever you are sailing, launching, or trailering with the mast up. The mast sticks up there a long way and shock or death could result if it comes in contact with overhead wires. So look up when moving the boat around or even stePPing the mast, and give any wires a wide berth.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hobie Holder 12 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hobie Holder 12 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hobie Holder 12 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hobie Holder 12 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hobie Holder 12, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hobie Holder 12.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hobie Holder 12. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hobie Holder 12 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
