Manuale d’uso / di manutenzione del prodotto N9120 del fabbricante Hitachi
Vai alla pagina of 48
HP Scanjet N9120 User Guide.
.
Contents 1 Use the scanner Scanner overview ................................................ ..................................... ......................... .. ......3 Scanner front panel butt ons ..................................... ................
Scanner initialization or ha rdware problems .............. .................... ..................... .....................30 Check that the scanner has power ....................................................................................30 Check the USB co nnection .
1 Use the scanner The following to pics describe the H P Scanjet N9120 scanner as well as how to scan or copy origin al documents. • Scanner overview • Load origina l documen ts • How to scan .
Scanner front pan el buttons Use the butt ons on the scanner fron t panel to start a scan and to config ure some scanner settings. Icon Button name Description 1 Copy By default, print the number of copies cu rrently configured in HP Document Copy. Alternatively, start the scanning software that is assigned to this button.
Icon Button name Description begin scanning again, press the Power Save button to wake up the scanne r. See also “ Scanner LEDs” on page 29 Scanner lamp setting The scanner supports two modes of lam p operation: • In Power Save mode, the scann er lamp times out and turns off automatically aft er about 15 minutes of i nactivity.
Weight: 49–120 g/m 2 (13–32 lb) NOTE: In the scanning softw are, set the page size to mat ch the width a nd length of the paper t hat you are scanni ng. • Scanning the f ollowing types of documents might result i n paper jams or da mage to the document s.
• For small or narrow docume nts, load the edge tha t is less than 148 mm (5.8 in) pointing into the feeder so that the longer edge can be pulled into the feeder an d passed along by the f eed rollers. • When loading small or lightweigh t documents, such as A6 cards (index cards) or U.
How to load docume nts 1. Flip up the pape r stop in the output tray that best matches the size of t he documents that you are scannin g. Select the stop posi tion that is clos est to (and beyond) the edge of your documents as th ey come out of the aut omatic document feeder (ADF).
4. Place the stack in the midd le of the input t ray. Load the st ack face up. For fastest scanning, lo ad the stack with th e left edge leading in to the ADF. NOTE: In the scanning sof tware, choose the layout setting that mat ches the orientation of the originals in t he ADF.
Place the original face down on the sca nner glass, as indi cated by the reference mark. NOTE: In the scanning softw are, choose the layout sett ing that mat ches the orientation of the ori ginal on the sca nner glass. How to scan The basic steps for scanning are: 1.
See also • “ Load original d ocuments” on page 5 • “ Associate a quick start button with scanning software ” on page 11 • “ Scan from scanning software” on page 11 • “ Work with .
Scan from ISIS- or TWAIN-complia nt scanning softw are 1. Start the scanning soft ware, and then select t he ISIS or TWAIN data source. 2. Select the settin gs that are appropriat e for the document s that you are scannin g. 3. Carry out the appropria te actions to complete the scan.
2 Useful scanner features Experienced documen t management p rofessionals might be interested in the followi ng scan features that are available i n the HP Sm art Document Scan Software. Many of these features are also avai lable from any IS IS- o r TWAIN-comp liant document scanning software t hat allows yo u to modi fy the scan se ttings.
3. In the Profile name box, type the name you want or acce pt the default na me. TIP: You might want to set up the new profile based on a n existing one. To d o so, select the Copy settin gs from pr ofile check box, and then select an existing profile from th e list.
NOTE: HP recommends scanning long pages individual ly at a resolution o f 300 dpi or lower. Filter out color from a document (color dropout) You can filter out a dark ba ckground from the im age content, f or example black text on green paper or red instru ctions on a form.
NOTE: To set the scan background co lor in another scannin g software, navigat e to the ISIS or TWAIN Advanced Se ttings dialog box. On the More tab, sele ct a color from the ADF Background drop-down list.
Scan without reviewing The standard process for using the HP Smart Document Scan Software to com plete your scans is as follows: 1. Scan document pages. 2. Review the scanned d ocument pages in the HP Smart Document Scan Sof tware Scan Progress Wi ndow .
Install or replace a print car tridge in the imprin ter The scanner uses an HP 51 604A print cartridge. You must purchase the print cartrid ge separate ly. 1. Raise the ADF input tray un til it clicks into place. 2. Lift the green l ever slightly, and slide t he imprinter comple tely to the lef t.
4. If you are replacing an empty prin t cartridge, slide it to the right to remov e it from the cartridge stall. 5. Remove the print ca rtridge from its packaging. Pul l the tab to remove the protective tape from the nozzles. 6. Hold the new print cartridg e with the nozzles dow n and slide it into the cart ridge stall.
1. Raise the ADF input tray un til it clicks into place. 2. Lift the green le ver slightly, an d then slide the i mprinter to the p osition that you want. NOTE: Several paper sizes are indicated in th e imprinter carriage. If you set the imprinter at the posi tion for the paper si ze that you are using, t he imprinter mark is printed abo ut 5 mm (.
1. Place a single page in t he automatic docume nt feeder input tray. 2. Press the Tools ( ) button on the scanner front pane l to open the H P Scanner Tools Utility. Click the Imprin ter tab. 3. In the Cartridge Status section, click Test Imprinter .
3 Care and maintenance This section present s information abou t how to care for and mai ntain the scann er. • Order maintenance an d scanning supplies • Clean the aut omatic document feeder • C.
If you use the ADF several t imes per week, monthly cl eaning is recommended. Set up a cleaning rout ine that is appr opriate for the scanner. 1. Press the Power switch to the off position, and th en disconnect the USB cab le and power cable from th e scanner.
3. Clean the clea r scanning strip on the scanner bed. Wipe the clear area with a clean, damp, lint-f ree clot h. 4. Close the sca nner lid. 5. Lift the latch on top of the ADF to open the top and side ADF access do ors.
6. Locate the white strip on t he side ADF access door and t he clear scan window i nside the ADF. Wipe b oth of these are as clean with a clean , damp, lint-f ree cloth. 7. Wipe the ADF rollers wi th a clean, damp, lint-free clot h. 8. Wait several minutes fo r the rollers to dry, and th en close the ADF access doors.
To clean the scanner gla ss, follow these step s: 1. Press the Power switch to the of f position, and t hen disconnect the U SB cable and power cable from the scanner. 2. Open the scanner lid. 3. Clean the glass by u sing a soft, lint-free cloth that has been sprayed with a mil d glass cleaner.
3. Clean the fil ter in one of the fo llowing ways: • Use compressed air to b low the debris off of the filter. • Use a vacuum to remove the debris f rom the filter. • Rinse the filter with water. NOTE: If the filter is damaged, repl ace it with a n ew filter.
4. Close all ADF access d oors, and then reconnect th e USB cable and power cable to the scanner. 5. Press the Power swi tch to the on position, and the n update the scanner mainte nance history: a . Press the Tools ( ) button on the scann er front panel to open t he HP Scanner Tools Utility.
4 Troubleshooting This section contai ns solutions for common problems with the scanner. • Scanner LEDs • Scanner initializa tion or hardware prob lems • Scanner operation p roblems • Scanner .
LED indications Scanner action or condition The Power LED is lit with a steady green light. The scanner is on and rea dy to scan. The Attention LED blinks green at a medium speed. The Power LED is lit with a steady green light. The scanner is scanning an original.
If the problem pe rsists after verifyi ng the above items, try the following: 1. Press the Power switch to the off position, and then disconnect the po wer cable from the scanner. 2. Wait 30 seconds. 3. Reconnect the powe r cable to the scanner, and t hen press the Power switch to the on position.
Uninstall an d then reinsta ll the H P Scanjet utilities If checking the sca nner cable connectio ns did not solve the problem, the p roblem might have occurred because of a n incomplete inst allation. Try uninstalling and then rein stalling the HP scanning utilities.
Scanner l amp stay s on The scanner lamp should t ime out and turn off automat ically after a period of inactivit y (about 15 minu tes). If the scan ner lamp re mains on after a long period of inactivity, turn off the scanne r, wait 30 seconds, and then turn the sc anner back on.
Scanned pages a re missing at the scan destina tion When scanning with the ADF , pages that stick t ogether are scanned as on e item. The hidden pages are not scanne d. Enable Misfeed (Multi pick) Detection to sto p the scan or copy process if mul tiple pages are fed into the sc anner at on e time.
When scanning from t he scanner glass, the it em might not be placed correctly on the scanner glass. Make sure that the ite m you are trying to scan is placed face do wn on the glass and the lid is closed.
Scanning at a higher resolution than ne cessary creates a larger file with no add itional benefit. • Color scans create larg er files than do black an d white scans. • If you are scanni ng a large numb er of pages at on e time, consider sca nning fewer pages at a time to create mo re, smaller files.
Buttons do not wo rk After each step, press a button to see if it is working correctly. I f the problem persists, proceed with the next step. 1. The buttons might b e disabled in the H P scanning softwa re. Ensure that t he Disa ble front panel buttons setting in the HP Scanne r Tools Utility i s cleared.
Wrong profile is used whe n the Scan button is press ed If you are using the HP Smart Docum ent Scan Software, use the HP Scanner Tools Ut ility to determine which HP Smar t Document Scan Sof tware profile is assigne d to the Scan button. If nece ssary, reset the prof ile assigned to the b utton.
Clear a jam from the automatic document feeder 1. Remove any loose pages f rom the automat ic document feeder (ADF) inpu t tray. 2. Lift the latch on top of t he ADF to open the t op and side ADF acce ss doors. 3. Remove any jammed pag es from the ADF input tray.
4. Remove any jammed p ages from inside the ADF. 5. Remove any jammed pag es from the ADF outpu t tray. 6. If the jammed p age still can not be removed, follow these st eps: a . Open the scanne r lid. b . Push the green tab toward the scanner lid to open the inner ADF access d oor.
7. Close the inner AD F access door, and then cl ose the scanner l id. 8. At the scan destinati on, examine the scan out put to determine whi ch page was the last to be completely scanned.
Automatic document feed er does not feed pap er • The automatic document feeder (ADF) access doors migh t not be securely latched. Open the ADF access do ors, and then close the doors by pressing firm ly. • A problem with the ADF hardware migh t exist.
5 Accessibility Accessibility features The N9120 scanner includes the following acce ssibility features: LED Reader The LED Reader is softwa re that outputs the status of the indicator LEDs on the scanner front panel to the computer monitor as the LEDs change.
Index A accessibility 43 ADF clean 22 clear jams 39 cut-off images 42 feeding, troubleshoot 42 load paper 5 maintenance 22 streaks, troubleshoot 35 applications scan from 12 Attention LED 29 B backgro.
profiles assign to quick start buttons 11 in HP Smart Document Scan Softwar e 13 programs scan from 12 Q quick start buttons associate with scanning software 11 troubleshoot 38 R replace feed roller 2.
46.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hitachi N9120 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hitachi N9120 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hitachi N9120 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hitachi N9120 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hitachi N9120, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hitachi N9120.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hitachi N9120. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hitachi N9120 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
