

Please read this guide before operating this equipment. After you finish reading this guide, store it in a safe place for future reference.

Copying Guide


The manuals for this machine are divided as follows. Please refer to them for detailed information. The manuals supplied with optional equipment are included in the list below. Depending on the system configuration and product purchased, some manuals may not be needed.
Guides with this symbol are PDF manuals included on the accompanying CD-ROM.
Guides with this symbol are printed manuals. CD-ROM



Introduction to Copying
Chapter 2
Basic Copying Features
Chapter 3
Special Copying Features
Chapter 4
Customizing Settings
Chapter 5
Appendix
Includes the Combination of Functions Chart and index.


Thank you for purchasing the Canon imageRUNNER 2010F. Please read this manual thoroughly before operating the machine in order to familiarize yourself with its capabilities, and to make the most of its many functions. After reading this manual, store it in a safe place for future reference.
Symbols Used in This Manual
The following symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety.
The following symbols and key names are a few examples of how keys to be pressed are expressed in this manual:
Press [F4] (L)
(Stop)

Illustrations used in this manual are those displayed when the imageRUNNER 2010F has the optional Finisher-L1 attached to it.

Trademarks
Canon, the Canon logo, and imageRUNNER are trademarks of Canon Inc.
Other product and company names herein may be the trademarks of their respective owners.
Copyright 2002 by Canon Inc. All rights reserved.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage or retrieval system without the prior written permission of Canon Inc.
The information in this document is subject to change without notice.
CANON INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, EITHER EXPRESS OR IMPLIED, EXCEPT AS PROVIDED HEREIN, INCLUDING WITHOUT LIMITATION, THEREOF, WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OF USE OR AGAINST INFRINGEMENT OF ANY PATENT. CANON INC. SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.

This chapter is an introduction to copying.
Overview of the imageRUNNER 2010F 1-2
Flow of Copy Operations 1-4
Placing Originals 1-10
Orientation 1-11 Platen Glass 1-12 Feeder (ADF-J1) 1-14
Canceling a Copy Job 1-16
Using the Stop Key 1-16 Using the System Monitor Screen 1-17
Reserved Copying 1-18
Reserving Copy Jobs While Printing 1-18
Interrupt Mode 1-20

Most operations of this machine are done from the control panel, Copy Basic Features screen, Special Features screen, and Additional Functions menu. To use the copy function of this machine, press the appropriate keys on the control panel in accordance with the selections on the LCD display.
This section provides an overview of the main features of this machine.
I Copy Basic Features Screen
The screen below, which appears when the machine is ready to make copies, is called the Copy Basic Features screen. You can set the following basic copy features from this screen:

I Special Features Screen
The screen below, which appears when you press [Special Features] on the control panel, is called the Special Features screen. You can set the following copy modes from this screen:

Overview of the imageRUNNER 2010F 1-2
Introduction to Copying

I Additional Functions Menu
The screen below, which appears when you press [Additional Functions], is called the Additional Functions menu. You can customize the following settings from this menu:

Overview of the imageRUNNER 2010F 1-3
Introduction to Copying

This section describes the flow of basic copy operations. Understanding the flow of copy operations is useful to help you learn how to use the machine’s basic features, and how to find information in this manual.
Machine,” in the Reference Guide. - Routine maintenance, see Chapter 7, “Routine Maintenance,” in the Reference Guide.
1 Press [COPY].
COPY
lights, and the Copy Basic Features screen appears.
Flow of Copy Operations 1-4
Introduction to Copying

G If the message <INSERT A CONTROL CARD> appears:
❑Insert a control card.
For instructions on using the optional Card Reader-E1, see Chapter 3, “Optional Equipment,” in the Reference Guide.
G If the message <ENTER DEPARTMENT ID AND PASSWORD>
❑Enter the Department ID and password © press [ID].

The Copy Basic Features screen appears.
For instructions on using Department ID Management, see Chapter 6, “System Manager Settings,” in the Reference Guide.
Flow of Copy Operations 1-5
Introduction to Copying

2 Place your original.
You can place your original both vertically and horizontally in the feeder or on the platen glass.
For instructions on placing your original, see “Placing Originals,” on p. 1-10.

3 Set the desired copy mode on the Copy Basic Features screen.
On the Copy Basic Features screen, you can select the copy ratio, paper size, and copy exposure and image quality settings.
Flow of Copy Operations 1-6
Introduction to Copying

4 Set the desired copy modes on the Special Features screen.
❑Press [Special Features].
❑Press the function keys under the modes that appear on the LCD display, and
which correspond to the copy modes you want to set.
5 Enter the copy quantity.
For instructions on setting the number of copies, see “Specifying the Required Number of Copies,” on p. 2-2.

6 Press [Start].
If the following screen is displayed, follow the instructions that appear on the LCD display © press (Start) once for each original. When scanning is complete, press (OK).

Copying starts.
While copying, you cannot change copy mode settings, such as the copy quantity, paper size, and copy ratio.
Flow of Copy Operations 1-7
Special Features · Introduction to Copying · Start

If there is a current job, the machine scans the original, and waits to print it. Printing starts when the current job is complete.
7 If you want to stop, interrupt, or copy another original during a copy job, follow the instruction below.
G If you want to stop a copy job:
❑Press [Stop].

❑Press [F3] (YES).
G If you want to cancel a copy job in the standby mode:
❑Press [Stop].

❑Press [F2] (M) or [F3] (L) to select the copy job you want to cancel © press
[F4] (CANCEL).
G If you want to interrupt a copy job:
❑To interrupt a copy job when you need to make priority copies, press [Interrupt].
For instructions on interrupting a copy job, see “Interrupt Mode,” on p. 1-20.
The message appears on the LCD display.

Flow of Copy Operations 1-8

G If you want to reserve a copy job and scan an original while the
❑Place your original © press [Start].
For instructions on reserving a copy job, see “Reserved Copying,” on p. 1-18.
8 When scanning is complete, remove your original.
9 If the optional Card Reader-E1 is attached, remove the control card.
For instructions on using the optional Card Reader-E1, see Chapter 3, “Optional Equipment,” in the Reference Guide.
10 If you have set Department ID Management, press [ID].
For instructions on using Department ID Management, see Chapter 6, “System Manager Settings,” in the Reference Guide.
Flow of Copy Operations 1-9
Start · Introduction to Copying

Place your originals on the platen glass or in the feeder, depending on the size and type of paper that you want to print, and the settings that you have specified.
Place the originals on the platen glass when scanning bound originals (such as books and magazines), originals on heavy or lightweight paper, and transparencies.
Place a stack of originals in the feeder © press [Start]. The machine automatically scans them into memory.

You can place an original either vertically or horizontally. Always align the top edge of your original with the back edge of the platen glass (by the arrow in the top left corner), or with the back edge of the feeder.

Vertical Placement Horizontal Placement


Vertical Placement Horizontal Placement

You should use the platen glass when scanning bound originals (such as books and magazines), originals on heavy or lightweight paper, and transparencies into memory.
1 Lift up the feeder.

This machine is equipped with an open/close sensor on the underside of the feeder (see circled area in the above illustration). When placing originals on the platen glass, lift the feeder about 11 7/8" (30 cm) so that the sensor detaches from the underside of the feeder. If the sensor does not detach from the underside of the feeder, the size of originals may not be detected correctly.
2 Place your original face down.
The surface that you want to scan into memory must be placed face down. Align the top edge of your original with the back edge of the platen glass (by the arrow in the top left corner).

Place books and other bound originals on the platen glass in the same way.
Introduction to Copying · Placing Originals 1-12

If you are enlarging an STMT or LTR original to 11" x 17" or LGL paper, place the original horizontally on the platen glass, and align it with the STMT or LTR marks. 3 Gently lower the feeder.

Remove the original from the platen glass when scanning is complete.

Introduction to Copying · Placing Originals 1-13

Place a stack of originals in the feeder, and press [Start]. The machine automatically scans them into memory.
You can place the following originals in the original supply tray:
1 Neatly place your originals face up in the original supply tray.
If you are enlarging LTR originals to 11'' x 17'' or LGL paper, place your originals horizontally.
Place your originals as far into the feeder as they will go.
A beep sounds when the originals are set correctly.

2 Adjust the slide guides to fit the size of your originals.


Introduction to Copying · Placing Originals 1-15

You can cancel a copy job in several ways.
1 Press [Stop].
Scanning stops.
G If only one copy job is being processed:
❑Press [F3] (YES).
If you do not want to cancel the copy job, press (NO).
The job is canceled.
G If multiple copy jobs are being processed:
❑Press [F2] (M) or [F3] (L) to select the copy job you want to cancel © press
[F4] (CANCEL).
If you do not want to cancel the selected copy job, press (BACK).
You cannot select multiple jobs and cancel them all at once.
If you want to cancel multiple jobs, select and cancel one job at a time.

The selected job is canceled.
Canceling a Copy Job 1-16
Introduction to Copying · Stop

You can cancel a job while it is waiting to be processed, or during printing.
1 Press [Monitor].
The status of all jobs is listed on the LCD display.

2 Press [F2] (M) or [F3] (L) to select the job to be canceled © press [F4] (CANCEL).
You cannot select multiple jobs and cancel them all at once.
If you want to cancel multiple jobs, select and cancel one job at a time.

3 Press [F3] (YES).
If you do not want to cancel the copy job, press (NO).
The selected job is canceled.
Canceling a Copy Job 1-17
Monitor · Introduction to Copying

You can select copy settings and scan originals even if the machine is currently printing. Your scanned documents are processed after the current job is complete.
The machine cannot scan originals while it is warming up, at power ON, or after clearing a paper jam.
You can set different copy modes for each job.
You can scan other originals, and set different copy modes while the machine is printing a previous job. The machine begins printing the reserved copy job after the current job completes. This helps you to handle multiple copy jobs more efficiently.
1 Press [COPY].
lights.
2 Place your original, and set the desired copy modes.
3 Press [Start].
Scanning starts.
To cancel a reserved copy job, press (Stop) © press (M) or (L) to select the reserved copy job © press (CANCEL).
Introduction to Copying · Start · Reserved Copying 1-18

4 When scanning is complete, remove the original from the machine.

Introduction to Copying · Reserved Copying 1-19

The Interrupt mode enables you to interrupt the reserved or current job that is printing long enough to make higher priority copies. This mode is useful if you need to make a rush copy during a long copy job.
You can make interrupt copies when the machine is ready to scan.
1 Press [COPY].
lights.
2 Press [Interrupt].
If you want to make copies after changing the Department ID while Department ID Management is enabled, press (ID) © enter the Department ID and password. (See Chapter 2, “Basic Operations,” in the Reference Guide.)
(Interrupt) lights.
If you press (Interrupt), the current job being output is not interrupted until the interrupt copy starts printing.
3 Place your original, and set the desired copy modes.

To cancel the Interrupt mode, press (Stop) © press (M) or (L) to select the reserved copy job © press (CANCEL).
Introduction to Copying · Interrupt · Interrupt Mode 1-20

4 Press [Start].
The interrupt copy job starts.
5 Once the original is scanned, remove it from the machine.

When the interrupt copy job is complete, the interrupted printing operation resumes.
If you want to continue making interrupt copies, wait until the current interrupt copy job is complete (end of printing). Then, repeat the process from step 2.
Start · Introduction to Copying · Interrupt Mode 1-21

Introduction to Copying · Interrupt Mode 1-22

This chapter describes the basic copying features.
Copy Quantity 2-2
Specifying the Required Number of Copies 2-2 Changing the Copy Quantity 2-2
Paper Selection 2-4
Automatic Paper Selection 2-4 Manual Paper Selection 2-5
Copy Exposure and Image Quality Adjustments 2-8
Copy Exposure (Manual) 2-9 Image Quality (Manual) 2-10 Copy Exposure and Image Quality (Automatic) 2-11
Changing the Copy (Zoom) Ratio 2-13
Preset Zoom 2-14 Zoom by Percentage 2-15 Auto Zoom 2-16
Collating Copies 2-18
Page Order (Collate) 2-20 Page Order (Staple) 2-22

You can make up to 99 copies for each copy job.
1 Press [COPY].
COPY
lights.
@.
DEF
2 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
The copy quantity appears in the upper right corner of the Copy Basic Features screen.
IMPORTANT
You cannot change the copy quantity while copying.
1 Press [Clear] to clear the entered number.
Basic Copying Features · Clear · Copy Quantity 2-2

@.
DEF
2 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
The copy quantity appears in the upper right corner of the Copy Basic Features screen.

You cannot change the copy quantity while copying.
Basic Copying Features · Copy Quantity 2-3

This mode enables you to set the machine to automatically select the paper size, or to manually specify a paper size for a copy job.
The machine automatically selects the copy paper.
DRAWER ELIGIBLTY menu (See Chapter 4, “Selecting and Storing Settings,” in the Reference Guide.)
Basic Copying Features · Paper Selection 2-4

1 Press [COPY].
COPY
lights.
2 Place your original © press [F2] (PAPER SELECT).

3 Make sure that <AUTO PAPER> is selected © press [OK].
The selected mode is set, and the display returns to the Copy Basic Features screen.
4 Press [Start].
Copying starts.
If the message appears, the paper loaded in the paper drawers is different from the original paper size. Load the appropriate paper. If you press (Start) without loading the correct paper size, the machine automatically selects the smallest loaded paper size, and starts copying.
You can make copies after manually selecting the paper size and type of paper loaded in the paper drawers or stack bypass.
If paper is selected manually, you cannot use the Rotate print mode even if ROTATE PRINT is set to ‘02 ON’ in the Common Settings menu. (See Chapter 4, “Selecting and Storing Settings,” in the Reference Guide.)
The paper sizes/types loaded in the paper drawers can be set from the Additional Functions menu. (See Chapter 4, “Selecting and Storing Settings,” in the Reference Guide.)
Basic Copying Features · Start · Paper Selection 2-5

1 Press [COPY].
COPY
lights.
2 Place your original © press [F2] (PAPER SELECT).
3 Press [F3] (M) or [F4] (L) to select the desired paper size.

G If you want to use the stack bypass:
❑Load the desired paper size and type in the stack bypass.

The Paper Size setting menu appears.
Basic Copying Features · Paper Selection 2-6

The display above appears only if the paper size is set to ‘01 OFF’ in the 06 USE STACK BYPASS menu. (See Chapter 4, “Selecting and Storing Settings,” in the Reference Guide.)
❑Press [F2] (SELECT PAPER).

❑Press [F3] (M) or [F4] (L) to select the paper type © press [OK].

The display returns to the Paper Size setting menu.
❑Press [F3] (M) or [F4] (L) to select the paper size © press [OK].

The display returns to the Paper Size setting menu.
4 Press [OK].
The display returns to the Copy Basic Features screen, and the selected paper size/type is displayed.
5 Press [Start].
Copying starts.
To cancel all settings and restore the machine’s standard settings, press (Reset).
Basic Copying Features · Start · Paper Selection 2-7

The exposure and image quality can be adjusted when the original is scanned.
I Copy Exposure (Manual)
This mode enables you to manually adjust the exposure to the most appropriate level for the original.
I Image Quality (Manual)
This mode enables you to adjust the image quality to the level best suited to the quality of text or photo originals. The following three modes are available for adjusting image quality:
Text Mode Text/Photo Mode Photo Mode

The world’s coral reefs, where brilliantly colored fish and a myriad of other tropical creatures come together. Aptly nicknamed “Tropical Forests under the sea”, these spots of breathtaking beauty serve as home to countless varieties of life, and to us of the land, this alluring, dream-like world forms a tropical paradise filled with romance.
The world’s coral reefs, where brilliantly colored fish and a myriad of other tropical creatures come together.

This mode is best suited for making copies from text originals. Blueprints or penciled originals can be copied clearly.
This mode is best suited for making copies from originals containing both text and photos.
This mode is best suited for making copies from photos printed on photographic paper, or photo originals containing halftones (i.e., printed photos).
I Copy Exposure and Image Quality (Automatic)
This mode enables you to set the machine to automatically adjust the exposure to the level best suited to the quality of the original.
Copy Exposure and Image Quality Adjustments 2-8
Basic Copying Features

You can manually adjust the exposure to the most appropriate level for the original.
1 Press [COPY].
lights.
2 Place your original © press [F3] (DENSITY).

3 Press [F1] (LIGHT) or [F3] (DARK) to adjust the exposure © press [OK].
Press (LIGHT) or (DARK) to move the indicator to the left to make the exposure lighter, or to the right to make the exposure darker.

The selected mode is set, and the display returns to the Copy Basic Features screen.
4 Press [Start].
Copying starts.
Copy Exposure and Image Quality Adjustments 2-9
Basic Copying Features · Start

This mode enables you to adjust the image quality to the level best suited to the quality of text or photo originals.
Combinations of these three modes (Text, Text/Photo, and Photo) cannot be set at once. If you select one of these modes, the previously set mode is canceled.
This mode is best suited for making copies from text originals. Blueprints or penciled originals can be copied clearly.
This mode is best suited for making copies from originals containing both text and photos.
This mode is best suited for making copies from photos printed on photographic paper, or photo originals containing halftones (i.e., printed photos).
If you make copies of an original containing halftones, such as a printed photograph using the Photo mode, moiré may occur. If this happens, you can soften this moiré effect by adjusting the Sharpness level. (See “Sharpness,” on p. 4-11.)
1 Press [COPY].
lights.
2 Place your original © press [F4] (IMAGEQUALITY).
Each time you press (IMAGEQUALITY), the next or previous menu option becomes highlighted.
Copy Exposure and Image Quality Adjustments 2-10


3 Select the image quality of the original (TEXT, TEXT/PHOTO, or PHOTO) © press [OK].

The selected mode is set, and the display returns to the Copy Basic Features screen.
4 Press [Start].
Copying starts.
This mode enables you to set the machine to automatically adjust the exposure to the level best suited to the quality of the original.
1 Press [COPY].
COPY
lights.
2 Place your original © press [F3] (DENSITY).
Copy Exposure and Image Quality Adjustments 2-11
Basic Copying Features · Start

3 Press [F2] (AUTO EXPOSUR) © [OK].

The exposure is automatically adjusted to the level best suited to the quality of the original, the image quality is set to ‘TEXT’, and the display returns to the Copy Basic Features screen.
4 Press [Start].
Copying starts.
To cancel all settings and restore the machine’s standard settings, press (Reset).
Copy Exposure and Image Quality Adjustments 2-12
Basic Copying Features · Start


This mode enables you to set the machine to adjust the copy ratio automatically, or to specify the copy ratio manually for a copy job.
If you want to make copies at the copy ratio of 100%, press (COPY RATIO) © (DIRECT 100%).
This mode enables you to reduce or enlarge standard size originals to another standard paper size.
I Zoom by Percentage
This mode enables you to reduce or enlarge original images by any copy ratio, in 1% increments.

This mode enables you to have the machine automatically select the appropriate copy ratio based on the size of the original and the selected copy paper.

Changing the Copy (Zoom) Ratio 2-13

This mode enables you to reduce or enlarge standard size originals to another standard paper size.
Place your originals horizontally in the following cases: - If you are enlarging LTR originals to 11'' x 17'' or LGL paper
Placing an original horizontally means setting the original with the longer side sideways. (See “Orientation,” on p. 1-11.)
The preset copy ratio when making reduced copies is: LGL → LTR (78%) 11'' x 17'' → LGL (73%) 11'' x 17'' → LTR (64%) 11'' x 17'' → STMT (50%)
The preset copy ratio when making enlarged copies is: STMT → 11'' x 17'' (200%) LTR → 11'' x 17'' (129%) LGL → 11'' x 17' (121%)
1 Press [COPY].
lights.
2 Place your original © press [F1] (COPY RATIO).

Changing the Copy (Zoom) Ratio 2-14
Basic Copying Features · I Reduce · I Enlarge

3 Press [F3] (REDUCE) or [F4] (ENLARGE) to select a preset reduction or enlargement ratio © press [OK].
Each time you press (REDUCE) or (ENLARGE), the next or previous menu option becomes highlighted.

The selected mode is set, the display returns to the Copy Basic Features screen, and the selected copy ratio is displayed.
4 Press [Start].
Copying starts.
Zoom by Percentage
This mode enables you to reduce or enlarge original images by any copy ratio, in 1% increments. The available copy ratios are from 50% to 200%.
1 Press [COPY].
COPY
lights.
2 Place your original © press [F1] (COPY RATIO).
Changing the Copy (Zoom) Ratio 2-15
Basic Copying Features · Start

@.
DEF
3 Set the copy ratio using the numeric keys © press [OK].
JKL
MNO
If you make a mistake when entering the value, press (Clear), and enter the correct value.
TUV
WXYZ
OPER SYMBOLS
If you enter a value outside the setting range, an error tone sounds. If the value you entered is less than 50, the copy ratio is automatically changed to 50%. If the value you entered is greater than 200, the copy ratio is automatically changed to 200%. Enter a value within the setting range.

The selected mode is set, the display returns to the Copy Basic Features screen, and the selected copy ratio is displayed.
4 Press [Start].
Copying starts.
Auto Zoom
This mode enables you to have the machine automatically select the appropriate copy ratio based on the size of the original and the selected copy paper. The available copy ratios are from 50% to 200%.
1 Press [COPY].
lights.
Changing the Copy (Zoom) Ratio 2-16
Basic Copying Features · Start

2 Place your original © press [F2] (PAPER SELECT) © specify the paper size.
For details about specifying the copy paper, step 3 of “Manual Paper Selection,” on p. 2-5.
Select a paper size other than . If you select , the copy ratio is automatically set to match the size of the paper loaded in the top paper drawer.
3 Press [F1] (COPY RATIO).
4 Press [F2] (AUTO ZOOM) © [OK].

The selected mode is set, the display returns to the Copy Basic Features screen, and the selected copy ratio is displayed.
5 Press [Start].
Copying starts.
Changing the Copy (Zoom) Ratio 2-17
Basic Copying Features · Start

The Finisher modes can be selected to collate the copies in various ways by copy sets.
For details on how these Finisher modes correspond to the optional units, see Chapter 3, "Optional Equipment," in the Reference Guide.
I Below is a list of finisher modes and paper sizes available for each optional
unit.
Optional Units Collate Rotate Offset Staple*1
✔ 11''x17'' , LGL , LTR , LTR , STMT
✔ 11''x17'' , LGL , LTR , LTR , STMT
✔*2 11''x17'' *3, LGL *3, LTR , LTR
✔ 11''x17'' , LGL , LTR , LTR , STMT
*1 For details about the stapling position, see Chapter 3, “Optional Equipment,” in the Reference Guide.
*2 You can staple up to 15 sheets at one time.
*3 Stapling is only available with the additional memory modules installed.

I If the Collate Mode Is Set:
The copies are automatically collated into sets arranged in page order. The output is as follows:
Originals Set 1 Set 2
Three Copies of Each Page Collated in Page Order

I If the Rotate Mode Is Set:
If originals of the same size are copied, the pages are automatically collated into sets arranged in page order, and are output in alternating directions as follows:
Set 1 Set 2 Set 3 Result
Three Copies of Each Page Collated in Page Order and Output in Alternating Directions

stack bypass - DRAWER ELIGIBLTY in Common Settings (from the Additional Functions menu) is set
to ‘02 ON’ for the paper drawer and stack bypass designated for the Rotate Collate mode. (See Chapter 4, “Selecting and Storing Settings,” in the Reference Guide.)

I If the Offset Mode Is Set:
The copies are automatically collated into sets arranged in page order, and shifted alternately to the front and back of the tray as follows:
Set 1 Set 2 Set 3 Result
Three Copies of Each Page Collated in Page Order and Shifted Alternately

I If the Staple Mode Is Set:
The copies are automatically collated into sets arranged in page order and stapled. The output is as follows:
Set 2 Set 3 Result
Three Copies of Each Page Collated in Page Order

1 Press [COPY].
COPY
lights.
2 Place your originals © press [Collate].

If AUTO SORT in Copy Settings (from the Additional Functions menu) is set to ‘01 ON’, the Collate mode is automatically set if you place your originals in the feeder. (See “Auto Sort,” on p. 4-8.)

G If you want to set the Rotate mode:
❑Make sure you have set SORT ROTATE in Copy Settings (from the Additional
Functions menu) to ‘01 ON’ before making copies. (See “Sort Rotate,” on p. 4-9.) ❑Proceed to step 3.
and stack bypass - DRAWER ELIGIBLTY in Common Settings (from the Additional Functions menu)
is set to ‘02 ON’ for the paper drawer and stack bypass designated for the Rotate Collate mode. (See Chapter 4, “Selecting and Storing Settings,” in the Reference Guide.) • If the Finisher-L1 (optional) is attached, the Rotate Collate mode cannot be set.
G If you want to set the Offset mode:
❑Set SORT ROTATE in Copy Settings (from the Additional Functions menu) to
‘01 ON’ before making copies. (See “Sort Rotate,” on p. 4-9.) ❑Proceed to step 3.
@.
DEF
3 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 2-2.

4 Press [Start].
If the original is placed on the platen glass, follow the instructions that appear on the display © press (Start) once for each original. When scanning is complete, press (OK).
Copying starts.
Basic Copying Features · Start · Collating Copies 2-21

1 Press [COPY].
COPY
lights.
2 Place your original © press [Collate] until <STAPLE SORT> appears.

If AUTO SORT in Copy Settings (from the Additional Functions menu) is set to ‘01 ON’, the Collate mode is automatically set if you place your originals in the feeder. (See “Auto Sort,” on p. 4-8.)
@.
DEF
3 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 2-2.

Basic Copying Features · Collate · Collating Copies 2-22

4 Press [Start].
If the original is placed on the platen glass, follow the instructions that appear on the display © press (Start) once for each original. When scanning is complete, press (OK).
Copying starts.
Start · Basic Copying Features · Collating Copies 2-23

Basic Copying Features · Collating Copies 2-24

This chapter describes special copying features for document layout, image adjustment, image manipulation, and other document features.
Two-Page Separation 3-2
Margin Mode 3-5
Frame Erase 3-8
Original Frame Erase 3-9 Book Frame Erase 3-11 Hole Punch Erase 3-14
Image Combination 3-17
Different Size Originals 3-22


The Two-Page Separation mode enables you to copy facing pages in a book or a magazine to fit onto separate sheets of paper.


2 Place your original on the platen glass © press [Special Features].
If you want to make copies in page order, begin copying from the first facing pages and work your way forward.
Place your original face down, so that its top edge is aligned with the top left corner of the platen glass by the arrow.

3 Press [F1] (2-PAGE SEP).

4 Press [F3] (LEFT OPENING) or [F4] (RGHT OPENING) to select the direction that the book opens © press [OK].

The Original Size setting menu appears.
Open and place the book frame face down on the platen glass as shown below, and according to the book’s opening direction you set in step 3.
The book is copied in the following manner when placed on the platen glass.
Cover Cover
The right half (1) of the platen glass is copied first, and the left half (2) is copied next. The left half (1) of the platen glass is copied first, and the right half (2) is copied next.
Special Copying Features · Two-Page Separation 3-3

5 Press [F4] (ORIGNAL SIZE) to select the paper size © press [OK].
Each time you press (ORIGNAL SIZE), the next or previous menu option becomes highlighted.

The selected mode is set, and the Copy Basic Features screen appears.
@.
DEF
6 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 2-2.

7 Press [Start].
If you want to continue copying other facing pages in the Two-Page Separation mode, place your original on the platen glass © press (Start).
Copying starts.
Special Copying Features · Start · Two-Page Separation 3-4


The Margin mode enables you to make copies with the entire original image shifted by a designated width to the left, right, top, or bottom in order to create a margin on the copies. Use this mode to make copies ready for placement in ring binders.


2 Place your original © press [Special Features].

3 Press [F2] (MARGIN).

4 Press [F1] (LEFT MARGIN), [F2] (RIGHT MARGIN), [F3] (TOP MARGIN), or [F4] (BOTTOM MRGN) to specify the type of margin © press [OK].

The Margin Width setting menu appears for the margin type you selected.
5 Press [F3] (–) or [F4] (+) to set the margin width (1 mm to 20 mm) © press [OK].
You can also use the numeric keys to enter the margin width, and (Clear) to clear the value.
If you enter a value outside the setting range, an error tone sounds. Enter a value within the setting range.

The selected mode is set, and the Copy Basic Features screen appears.
The default setting is ‘10 mm’.
Special Copying Features · Margin Mode 3-6

@.
DEF
6 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 2-2.

7 Press [Start].
Copying starts.
Start · Special Copying Features · Margin Mode 3-7


The Frame Erase mode enables you to erase shadows and lines that appear when copying various types of originals. The following three Frame Erase modes are available.
I Original Frame Erase
This mode erases the dark borders and frame lines that appear around the copy when the original is smaller than the selected paper size. Also, it creates a blank border around the edge of the copy.

Special Copying Features · Frame Erase 3-8

I Book Frame Erase
This mode erases the dark border, as well as center and contour lines that appear when copying facing pages in a bound original onto a single sheet of paper.

I Hole Punch Erase
This mode erases the shadows that appear in copies from binding holes on originals.

This mode erases the dark borders and frame lines that appear around the copy when the original is smaller than the selected paper size. Also, it creates a blank border around the edge of the copy.
Special Copying Features · Frame Erase 3-9

1 Press [COPY].
COPY
lights.
2 Place your original © press [Special Features].
3 Press [F3] (FRAME ERASE).

4 Make sure that <FRAME ERASE> is selected © press [OK].
The Original Size setting menu appears.
5 Press [F4] (ORIGNAL SIZE) to select the size of the original © press [OK].
Each time you press (ORIGNAL SIZE), the next or previous menu option becomes highlighted.

The selected mode is set, and the Copy Basic Features screen appears.
Special Features · Special Copying Features · Frame Erase 3-10

@.
DEF
6 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 2-2.

7 Press [Start].
Copying starts.
This mode erases the dark border, as well as the center and contour lines that appear when copying facing pages in a book onto a single sheet of paper.
If the machine is operating in the Book Frame Erase mode, you cannot use the Image Combination, or Different Size Originals modes.
1 Press [COPY].
COPY
lights.
Special Copying Features · Start · Frame Erase 3-11

2 Place your original on the platen glass © press [Special Features].
3 Press [F3] (FRAME ERASE).
4 Press [F3] (BOOK FR ERS) © [OK].

The Original Size setting menu appears.
5 Press [F4] (ORIGNAL SIZE) to select the size of the book when opened © press [OK].
Each time you press (ORIGNAL SIZE), the next or previous menu option becomes highlighted.

The Frame Erase Width setting menu appears.
Special Features · Special Copying Features · Frame Erase 3-12

6 Press [F3] (–) or [F4] (+) to set the desired book frame erase width (3 mm to 50 mm) for the center line © press [OK].
You can also use the numeric keys to enter the book frame erase width, and (Clear) to clear the value.
If you enter a value outside the setting range, an error tone sounds. Enter a value within the setting range.

The selected mode is set, and the Copy Basic Features screen appears.
The default setting is ‘10 mm’.
@.
DEF
7 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 2-2.

8 Press [Start].
Copying starts.
Special Copying Features · Start · Frame Erase 3-13

This mode erases the shadows that appear in copies from binding holes on originals.
1 Press [COPY].
COPY
lights.
2 Place your original © press [Special Features].
3 Press [F3] (FRAME ERASE).
4 Press [F4] (HOLE/P ERASE) © [OK].

The Original Size setting menu appears.
Special Copying Features · Special Features · Frame Erase 3-14

5 Press [F4] (ORIGNAL SIZE) to select the size of the original © press [OK].
Each time you press (ORIGNAL SIZE), the next or previous menu option becomes highlighted.

The Frame Erase Width setting menu appears.
6 Press [F3] (–) or [F4] (+) to set the desired hole punch erase width (3 mm to 20 mm) © press [OK].
You can also use the numeric keys to enter the hole punch erase width, and (Clear) to clear the value.
If you enter a value outside the setting range, an error tone sounds. Enter a value within the setting range.

The selected mode is set, and the Copy Basic Features screen appears.
The default setting is ‘18 mm’.
Special Copying Features · Frame Erase 3-15

@.
DEF
7 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 2-2.

8 Press [Start].
Copying starts.
Start · Special Copying Features · Frame Erase 3-16


This mode enables you to automatically reduce two or four originals to fit onto one side of a selected paper size.
I 2 on 1
This setting reduces two originals to fit onto one copy sheet, and allows you to select the layout order of each original. The following two layout types are available:

The originals are printed in the following order: left half (1) → right half (2)
The originals are printed in the following order: right half (1) → left half (2)
The layout order cannot be specified when you place an original horizontally.
Special Copying Features · Image Combination 3-17

I 4 on 1
This setting reduces four originals to fit onto one copy sheet, and allows you to select the layout order of each original. The following four layout types are available:

The originals are printed in the following order: upper left (1) → upper right (2) → lower left (3) → lower right (4)
The originals are printed in the following order: upper right (1) → upper left (2) → lower right (3) → lower left (4)
The originals are printed in the following order: upper left (1) → lower left (2) → upper right (3) → lower right (4)
The originals are printed in the following order: upper right (1) → lower right (2) → upper left (3) → lower left (4)
The layout order can be specified for an original placed horizontally.

2 Place your originals © press [Special Features].
Special Copying Features · Special Features · Image Combination 3-18

If AUTO SORT in Copy Settings (from the Additional Functions menu) is set to ‘01 ON’, the Collate and Offset Collate mode is automatically set if you place your originals in the feeder. (See “Auto Sort,” on p. 4-8.)
3 Press [F4] (LAYOUT COPY).

4 Press [F4] (ORIGNAL SIZE) to select the size of the original © press [OK].
Each time you press (ORIGNAL SIZE), the next or previous menu option becomes highlighted.

The Copy Layout setting menu appears.
5 Press [F2] (2 ON 1 COMB) or [F3] (4 on 1) to select the type of layout.
Screen shown if a vertically placed original ( ) is selected in step 4:

is grayed out if you selected a horizontally placed original ( ) in step 4:

Special Copying Features · Image Combination 3-19

6 Press [F4] (OPTIONS) to select the layout order of the originals.
G If you selected <2 ON 1 COMB> in step 5:
❑Press [F3] (No. 1) or [F4] (No. 2) to select the desired layout order © press
[OK] © [OK].

The Paper Size setting menu appears.
G If you selected <4 on 1> in step 5:
❑Press [F1] (No. 1), [F2] (No. 2), [F3] (No. 3), or [F4] (No. 4) to select the desired
layout order © press [OK] © [OK].

The Paper Size setting menu appears.
7 Press [F2] (STACK BYPASS), [F3] (M), or [F4] (L) to select the paper size © press [OK].

The selected mode is set, and the Copy Basic Features screen appears.
You cannot use Automatic Paper Selection in the Image Combination mode.
The machine automatically selects the copy ratio, depending on the selected paper size.
Special Copying Features · Image Combination 3-20

@.
DEF
8 Enter the desired copy quantity (1 to 99) using the numeric keys.
JKL
MNO
PRS
TUV
WXY
For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 2-2.

9 Press [Start].
When the original is placed on the platen glass, follow the instructions that appear on the display © press (Start) once for each original. When scanning is complete, press (OK).
Copying starts.
Start · Special Copying Features · Image Combination 3-21

This mode enables you to copy different size originals together in one group, as long as they have one side with an equal length (i.e., LTR and 11" x 17" ). Just make sure that the sides of the originals with the same length be lined up when you place them in the feeder and the machine will automatically select the appropriate paper size and copy ratio for each original.
In order to use the Different Size Originals mode, you need to assign this function to a Shortcut key in the Additional Functions menu before making copies. (See “Using Shortcut Keys,” on p. 4-15.)
You can use the stack bypass for the Automatic Paper Selection when: - The paper is loaded in the stack bypass - The paper size has been specified in 06 USE STACK BYPASS in COMMON
SETTINGS from the Additional Functions menu - Automatic Paper Selection is set to ‘02 ON’ for the stack bypass in the DRAWER
1 Press [COPY].
COPY
lights.
2 Place your originals in the feeder © press the Shortcut key ([1] to [4]) where you registered the Different Size Originals mode.

Different Size Originals 3-22

If AUTO SORT in Copy Settings (from the Additional Functions menu) is set to ‘01 ON’, the Collate or the Offset Collate mode is automatically set if you place your originals in the feeder. (See “Auto Sort,” on p. 4-8.)
3 Set the desired copy modes.

4 Press [Start].
Copying starts.
To cancel all settings and restore the machine’s standard settings, press (Reset).
Different Size Originals 3-23
Start · Special Copying Features

Different Size Originals 3-24
Special Copying Features

This chapter describes the setting/storing specifications of the copy functions.
Copy Settings Table 4-2
Changing the Current Standard Settings 4-3
Image Quality and Copy Exposure 4-3 Zoom Ratio 4-5 Copy Quantity 4-6 Frame Erase Width 4-7 Auto Sort 4-8 Sort Rotate 4-9 Sharpness 4-11 Prescan 4-13
Using Shortcut Keys 4-15
Assigning Functions 4-15 Making Copies 4-17

The following items can be stored or set in the Copy Settings menu, from the Additional Functions menu.
Item Available Settings Applicable
02 STD ZOOM RATIO 50% to 200%; 100%* 4-5
03 STANDARD COPY QTY 01 to 99; 01* 4-6
04 FRAME ERASE WIDTH 01 mm to 20 mm; 02 mm* 4-7
06 SORT ROTATE ON*/OFF 4-9
REDUCE* (SHORTCUT KEY1), ENLARGE* (SHORTCUT KEY2), DIRECT 100%, AUTO ZOOM, DARK, LIGHT, AUTO EXPOSURE, MARGIN, FRAME ERASE* (SHORTCUT KEY4), 2-PAGE SEP* (SHORTCUT KEY3), LAYOUT COPY, STAPLE SORT, USE STACK BYPASS, DIF SIZE DOC
08 SHARPNESS 1 to 9; 5* 4-11
An asterisk (*) indicates the default setting.
Copy Settings Table 4-2
Page · Customizing Settings

The standard settings refer to a combination of copy modes that the machine automatically applies at power ON or when [Reset] is pressed. This section explains the procedure for changing copy modes stored as standard settings.
This setting enables you to set the standard copy image quality and exposure.
The default settings are ‘TEXT’ for Image Quality and ‘5’ (center) for the Copy Exposure.
1 Press [Additional Functions].
The ADDITIONAL FUNCTIONS menu appears.
2 Press [F3] (M) or [F4] (L) to highlight <02 COPY SETTINGS> © press [OK].
Each time you press (M) or (L), the next or previous menu option becomes highlighted.
Changing the Current Standard Settings 4-3
Customizing Settings · Additional Functions

The COPY SETTINGS menu appears.
3 Press [F3] (M) or [F4] (L) to highlight <01 STD IMAGE QUAL/ EXP> © press [OK].

The STD IMAGE QUAL/EXP menu appears.
4 Set the desired standard copy image quality and exposure © press [OK].
For details about adjusting the copy image quality and exposure, see “Specifying the Required Number of Copies,” on p. 2-2.

The selected mode is set, and the display returns to the COPY SETTINGS menu.
You can set the copy exposure between 1 and 9.
5 Press [Reset] to return to the Copy Basic Features screen.
Changing the Current Standard Settings 4-4
Customizing Settings · Reset

This setting enables you to set the standard copy (zoom) ratio.
The default setting is ‘100%’.
1 Press [Additional Functions] © press [F3] (M) or [F4] (L) to highlight <02 COPY SETTINGS> © press [OK].
The COPY SETTINGS menu appears.
2 Press [F3] (M) or [F4] (L) to highlight <02 STD ZOOM RATIO> © press [OK].
Each time you press (M) or (L), the next or previous menu option becomes highlighted.

The STD ZOOM RATIO menu appears.
3 Press [F2] (–) or [F3] (+) to set the desired standard zoom ratio (50% to 200%) © press [OK].
You can also use the numeric keys to enter the standard zoom ratio, and (Clear) to clear the value.
If you enter a value outside the setting range, an error tone sounds. Enter a value within the setting range.

The selected mode is set, and the display returns to the COPY SETTINGS menu.
Changing the Current Standard Settings 4-5
Additional Functions · Customizing Settings

4 Press [Reset] to return to the Copy Basic Features screen.
This setting enables you to set the standard copy quantity.
The default setting is ‘01’.
1 Press [Additional Functions] © press [F3] (M) or [F4] (L) to highlight <02 COPY SETTINGS> © press [OK].
The COPY SETTINGS menu appears.
2 Press [F3] (M) or [F4] (L) to highlight <03 STANDARD COPY QTY> © press [OK].
Each time you press (M) or (L), the next or previous menu option becomes highlighted.

The STANDARD COPY QTY menu appears.
3 Press [F2] (–) or [F3] (+) to set the desired standard copy quantity (01 to 99) © press [OK].
You can also use the numeric keys to enter the standard copy quantity, and (Clear) to clear the value.
If you enter a value outside the setting range, an error tone sounds. Enter a value within the setting range.
Changing the Current Standard Settings 4-6
Reset · Additional Functions · Customizing Settings


The selected mode is set, and the display returns to the COPY SETTINGS menu.
4 Press [Reset] to return to the Copy Basic Features screen.
This setting enables you to set the standard frame erase width for the Frame Erase mode.
The default setting is ‘02 mm’.
1 Press [Additional Functions] © press [F3] (M) or [F4] (L) to highlight <02 COPY SETTINGS> © press [OK].
The COPY SETTINGS menu appears.
2 Press [F3] (M) or [F4] (L) to highlight <04 FRAME ERASE WIDTH> © press [OK].
Each time you press (M) or (L), the next or previous menu option becomes highlighted.

The FRAME ERASE WIDTH menu appears.
Changing the Current Standard Settings 4-7
Reset · Customizing Settings · Additional Functions

3 Press [F2] (–) or [F3] (+) to set the desired frame erase width (01 mm to 20 mm) © press [OK].
You can also use the numeric keys to enter the standard frame erase width, and
(Clear) to clear the value.
If you enter a value outside the setting range, an error tone sounds. Enter a value within the setting range.

The selected mode is set, and the display returns to the COPY SETTINGS menu.
4 Press [Reset] to return to the Copy Basic Features screen.
This setting allows automatic selection of the Collate (Offset Collate) mode when the originals are placed in the feeder. This is helpful when making multiple copies, because you do not need to remember to select the Finishing mode.
1 Press [Additional Functions] © press [F3] (M) or [F4] (L) to highlight <02 COPY SETTINGS> © press [OK].
The COPY SETTINGS menu appears.
Changing the Current Standard Settings 4-8
Reset · Customizing Settings · Additional Functions

2 Press [F3] (M) or [F4] (L) to highlight <05 AUTO SORT> © press [OK].
Each time you press (M) or (L), the next or previous menu option becomes highlighted.

The AUTO SORT menu appears.
3 Press [F3] (M) or [F4] (L) to select <01 ON> or <02 OFF> © press [OK].
If you want the machine to collate automatically, select .
If you do not want the machine to collate automatically, select .

The selected mode is set, and the display returns to the COPY SETTINGS menu.
4 Press [Reset] to return to the Copy Basic Features screen.
This setting allows automatic selection of the Rotate Collate mode when the original is placed in the feeder. For more details about the Rotate Collate mode, see “Collating Copies,” on p. 2-18.
stack bypass - DRAWER ELIGIBLTY in Common Settings (from the Additional Functions menu) is set
to ‘02 ON’ for the paper drawer and stack bypass designated for the Rotate Collate mode. (See Chapter 4, “Selecting and Storing Settings,” in the Reference Guide.)
Changing the Current Standard Settings 4-9
Customizing Settings · Reset

The default setting is ‘01 ON’.
1 Press [Additional Functions] © press [F3] (M) or [F4] (L) to highlight <02 COPY SETTINGS> © press [OK].
The COPY SETTINGS menu appears.
2 Press [F3] (M) or [F4] (L) to highlight <06 SORT ROTATE> © press [OK].
Each time you press (M) or (L), the next or previous menu option becomes highlighted.

The SORT ROTATE menu appears.
3 Press [F3] (M) or [F4] (L) to select <01 ON> or <02 OFF> © press [OK].
If you want the machine to rotate collate automatically, select .
If you do not want the machine to rotate collate automatically, select .

The selected mode is set, and the display returns to the COPY SETTINGS menu.
4 Press [Reset] to return to the Copy Basic Features screen.
Changing the Current Standard Settings 4-10
Additional Functions · Customizing Settings · Reset

This setting enables you to make copies of the original image with a sharper or a softer contrast. To reproduce copies with text or lines with a sharper contrast, select [F3] (SHARP) as the setting. To reproduce copies with photographs or other halftones with a softer contrast, select [F2] (DULL) as the setting.
If you make copies of an original image containing halftones, such as a printed photograph, using the Photo mode, moiré may occur. However, by using [F2] (DULL), you can soften this moiré effect so that the copy is easier on the eyes.
Dull Is Set Dull Is Not Set Copy

The world's coral reefs, where brilliantly colored fish and a myriad of other creatures of the tropics come together.
The world's coral reefs, where brilliantly colored fish and a myriad of other creatures of the tropics come together.
The world's coral reefs, where brilliantly colored fish and a myriad of other creatures of the tropics come together.
This setting enhances the edges of original images so that faint or fine text is reproduced with a sharper contrast. This setting is particularly suited for blueprints and faint pencil drawn original images.
Sharp Is Set Sharp Is Not Set Copy
The world’s coral reefs, where brilliantly colored fish and a myriad of other tropical creatures come together. Aptly nicknamed “Tropical Forests under the sea”, these spots of breathtaking beauty serve as home to countless varieties of life, and to us of the land, this alluring, dream-like world forms a tropical paradise filled with romance.
The world’s coral reefs, where brilliantly colored fish and a myriad of other tropical creatures come together. Aptly nicknamed “Tropical Forests under the sea”, these spots of breathtaking beauty serve as home to countless varieties of life, and to us of the land, this alluring, dream-like world forms a tropical paradise filled with romance.
The world’s coral reefs, where brilliantly colored fish and a myriad of other tropical creatures come together. Aptly nicknamed “Tropical Forests under the sea”, these spots of breathtaking beauty serve as home to countless varieties of life, and to us of the land, this alluring, dream-like world forms a tropical paradise filled with romance.
Changing the Current Standard Settings 4-11

1 Press [Additional Functions] © press [F3] (M) or [F4] (L) to highlight <02 COPY SETTINGS> © press [OK].
The COPY SETTINGS menu appears.
2 Press [F3] (M) or [F4] (L) to highlight <08 SHARPNESS> © press [OK].
Each time you press (M) or (L), the next or previous menu option becomes highlighted.

The SHARPNESS menu appears.
3 Press [F2] (DULL) or [F3] (SHARP) to set the desired sharpness level © press [OK].
To copy text and lines clearly, press (SHARP) to select a higher sharpness level.
To copy halftone images, such as a photograph, press (DULL) to select a lower sharpness level.

The selected mode is set, and the display returns to the COPY SETTINGS menu.
4 Press [Reset] to return to the Copy Basic Features screen.
Changing the Current Standard Settings 4-12
Additional Functions · Customizing Settings · Reset

When you press [Start] in a regular scanning operation, the machine goes through a warming-up process each time before it actually starts scanning the document. The Prescan mode function keeps the machine warmed up so it starts scanning as soon as you press [Start], thereby shortening the scanning time.
1 Press [Additional Functions] © press [F3] (M) or [F4] (L) to highlight <02 COPY SETTINGS> © press [OK].
The COPY SETTINGS menu appears.
2 Press [F3] (M) or [F4] (L) to highlight <09 PRESCAN> © press [OK].
Each time you press (M) or (L), the next or previous menu option becomes highlighted.

The PRESCAN menu appears.
3 Press [F3] (M) or [F4] (L) to select <01 ON> or <02 OFF> © press [OK].
If you want to use the prescan function, select .
If you do not want to use the prescan function, select .
Changing the Current Standard Settings 4-13
Additional Functions · Customizing Settings


The selected mode is set, and the display returns to the Additional Functions menu.
4 Press [Reset] to return to the Copy Basic Features screen.
Changing the Current Standard Settings 4-14
Reset · Customizing Settings

The shortcut keys enable you to assign the most frequently used copy functions to the shortcut keys, and to call up these functions with a single key press when making copies. You can assign up to four copy modes to the shortcut keys.
Combination, Staple Sort (only when the Finisher-L1 (optional) is attached), Paper Size for the Stack Bypass, and Different Size Originals
Follow the procedure described below to assign the most frequently used copy modes to the shortcut keys.
1 Press [Additional Functions] © press [F3] (M) or [F4] (L) to highlight <02 COPY SETTINGS> © press [OK].
The COPY SETTINGS menu appears.
Using Shortcut Keys 4-15
Customizing Settings · Additional Functions

2 Press [F3] (M) or [F4] (L) to highlight <07 SHORTCUT KEY SET> © press [OK].
Each time you press (M) or (L), the next or previous menu option becomes highlighted.

The SHORTCUT KEY SET menu appears.
3 Press [F3] (M) or [F4] (L) to select a shortcut key © press [OK].

The SHORTCUT KEY menu appears.
4 Press [F3] (M) or [F4] (L) to select the desired copy mode you want to assign to the selected shortcut key © press [OK].

The selected copy mode is assigned to the selected shortcut key, and the display returns to the SHORTCUT KEY SET menu.
5 Press [Reset] to return to the Copy Basic Features screen.
Using Shortcut Keys 4-16
Customizing Settings · Reset

Using the shortcut keys simplifies a routine procedure when you make copies.
1 Press [COPY].
lights.
2 Place your original © press the desired Shortcut key ([1] to [4]) that contains the copy mode you want to set.
You can skip a few steps to set each function. (e.g. Enlarge function)
3 If necessary, specify the settings for each mode.
For details about the setting procedure for a particular copy mode, see the applicable page numbers in the table below.
Copy Ratio P. 2-13
Exposure P. 2-9
Margin P. 3-5
Frame Erase P. 3-8
Two-Page Separation P. 3-2
Image Combination P. 3-17
Staple Sort P. 2-22
Paper Size for the Stack Bypass Reference Guide
Different Size Originals P. 3-22
4 Press [Start].
Copying starts.
Using Shortcut Keys 4-17

Using Shortcut Keys 4-18
Customizing Settings

This chapter provides the Combination of Functions Chart and index.
Combination of Functions Chart 5-2
Index 5-6

This chart shows the setting combinations when you want to reconfigure the functions.
Reserve Copy Interrupt Copy Staple Offset Collating Rotate Collating Collate Stack Bypass (Free size paper) Stack Bypass Automatic Paper Selection Text/Photo
Automatic Exposure Control Auto Zoom
Function to Be Set
Preset Zoom Zoom Designation Auto Zoom Automatic Exposure Control Photo Text Text/Photo Automatic Paper Selection Stack Bypass Stack Bypass (Free size paper) Collate Rotate Collating Offset Collating Staple Interrupt Copy Reserve Copy
Combination of Functions Chart 5-2

Stack Bypass (Free size paper)
Automatic Paper Selection Text/Photo
Reserve Copy Interrupt Copy Staple Offset Collating Rotate Collating Collate
Function to Be Set
Two-Page Separation Image Combination (2 on 1) Image Combination (4 on 1) Original Frame Erase Book Frame Erase Hole Punch Erase Right Margin Left Margin Top Margin Bottom Margin Different Size Originals
Combination of Functions Chart 5-3

Image Combination (2 on 1)
Image Combination (4 on 1)
Top Margin Left Margin Right Margin
Function to Be Set
Preset Zoom Zoom Designation Auto Zoom Automatic Exposure Control Photo Text Text/Photo Automatic Paper Selection Stack Bypass Stack Bypass (Free size paper) Collate Rotate Collating Offset Collating Staple Interrupt Copy Reserve Copy
Combination of Functions Chart 5-4

Image Combination (4 on 1) Image Combination (2 on 1)
Top Margin Left Margin Right Margin
Function to Be Set
Two-Page Separation Image Combination (2 on 1) Image Combination (4 on 1) Original Frame Erase Book Frame Erase Hole Punch Erase Right Margin Left Margin Top Margin Bottom Margin Different Size Originals
Combination of Functions Chart 5-5

Flow of Copy Operations, 1-4 Frame Erase, 3-8
OK key, 1-7 Orientation, 1-11
Book Frame Erase, 3-9, 3-11 Hole Punch Erase, 3-9, 3-14 Original Frame Erase, 3-8, 3-9 Frame Erase width, 4-7
Horizontal placement, 1-11 Vertical placement, 1-11 Original Frame Erase, 3-8, 3-9 Overview, 1-2
P
Hole Punch Erase, 3-9 Horizontal placement, 1-11
Automatic, 2-4 Manual, 2-5 Password, 1-5 Photo mode, 2-10 Placing Originals, 1-10
Feeder (ADF-J1), 1-14 Orientation, 1-11 Platen Glass, 1-12 Platen glass, 1-4, 1-10 Prescan, 4-13 Preset Zoom
2 on 1, 3-17 4 on 1, 3-18 Image Quality, 2-10, 4-3
Automatic, 2-8, 2-11 Manual, 2-8, 2-10 Inner 2-Way Tray-B1, 2-18 Interrupt mode, 1-20
Enlarge, 2-14 Reduce, 2-14 Preset zoom, 2-14
While printing, 1-18 Reset key, 2-7 Right margin, 3-5 Rotate mode, 2-18, 2-19
Main power, 1-4 Margin mode, 3-5
N
Sharp, 4-11 Sharpness, 4-11 Shortcut keys, 4-15 Sort rotate, 4-9 Special Features key, 1-2 Special Features screen, 1-2 Stack bypass, 2-4
Offset mode, 2-18, 2-20

Standard settings, 4-3 Staple mode, 2-18, 2-20 Start key, 1-7 Stop key, 1-8, 1-16
Text mode, 2-10 Text/Photo mode, 2-10 Top margin, 3-5 Two-Page Separation, 3-2
Using Shortcut Keys, 4-15
Assigning Functions, 4-15 Making Copies, 4-17
Zoom by percentage, 2-15 Zoom ratio, 4-5
Appendix · Vertical placement, 1-11 · Index 5-8

The contents of this guide are
printed on 70% recycled paper.
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success, NY 11042, U.S.A. CANON CANADA INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada CANON EUROPA N.V. Bovenkerkerweg 59-61 P.O. Box 2262, 1180 EG Amstelveen, The Netherlands CANON FRANCE S.A. 17,quai du President Paul Doumer 92414 Courbevoie Cedex, France CANON (U.K.) LTD. Woodhatch, Reigate, Surrey, RH2 8BF, United Kingdom CANON DEUTSCHLAND GmbH Europark Fichtenhain A10, 47807 Krefeld, Germany CANON ITALIA S.p.A. Palazzo L Strada 6 20089 Milanofiori Rozzano (MI) Italy CANON LATIN AMERICA, INC. 703 Waterford Way, Suite400 Miami, Florida 33126 U.S.A. CANON AUSTRALIA PTY. LTD 1 Thomas Holt Drive, North Ryde, Sydney, N.S.W. 2113, Australia CANON SINGAPORE PTE. LTD. 79 Anson Road #09-01/06, Singapore 079906 CANON HONGKONG CO., LTD 9/F, The Hong Kong Club Building, 3A Chater Road, Central, Hong Kong
FA7-3245-020 072002NF C CANON INC. 2002 PRINTED IN CHINA
I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.