Manuale d’uso / di manutenzione del prodotto HW173DBB del fabbricante Hanns.G
Vai alla pagina of 20
HW173 HSG1044.
User’s Manual Before operating the monitor, please read this manual thoroughly. This m anual should be retained for future reference. FCC Class B Radio Fr equency Interference S tatement This equipment has been tested and found to comply with the lim its for a Class B digital device, pursuant to Part 15 of the FCC Rules.
User’s Manual RECYCLING INFORMATION We, the Hanns.G care very much about our environm ent protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life.
User’s Manual T ABLE OF CONTENTS SAFETY NOTICE ...................................................................................................... 5 PRECAUTIONS .....................................................................................
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any , must be used in order to comply with the emission limits.
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are norm al with LCD monitor and do not indicate a problem. x Due to the nature of the fluorescent light, the screen m ay flicker during initial use. T urn off the Power Switch and then turn it on again to make sure the flicker disappears.
User’s Manual BEFORE OPERA TING THE MONIT OR FEA TURES x 17” W ide screen TFT Color LCD Monitor x Crisp, Clear Display for W indows x Recommended Resolutions : 1440 X 900@60Hz x EP A ENERGY ST AR .
User’s Manual INST ALLA TION INSTRUCTIONS Install Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base.
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC T urn off your com puter before performing the procedure below . 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer ’ s D-Sub port.
User’s Manual ADJUSTING THE VIEWING ANGLE x For optimal viewing it is recommended to look at the full face of the m onitor , and then adjust the monitor ’ s angle to your own preference. x Hold the stand so you do not topple the monitor when you change the monitor’ s angle.
User’s Manual OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or of f. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preference.
User’s Manual FRONT P ANEL CONTROL x Power Button: Press this button to switch ON/OFF monitor ’ s power . x Power Indicator: Green — Power On mode. Orange — Power Saving mode. x MENU / RETURN: 1. T urn the OSD menu on/off or return to the previous m enu.
User’s Manual HOW TO ADJUST A SETTINGS BRIGHTNESS/CONTRAST BRIGHTNESS Adjust the brightness value of the display according to your preference. Select ψ BRIGHTNESS ω option to adjust the brightness value. CONTRAST Adjust the contrast value of the display according to your preference.
User’s Manual H-POSITION Select the ψ H-POSITION ω option to shift the screen image to the left or right. Enter the option and adjust the level. [For VGA only] V - POSITION Select the ψ V -POSITION ω option to shift the screen image up or down. Enter the option and adjust the level.
User’s Manual F ACT OR Y RESET Select the ψ F ACTOR Y RESET ω option to reset to the monitor’ s default setting. This will erase the current settings. Enter the option and select On or Of f. INFORMA TION Display Horizontal frequency/V ertical frequency/Resolution information.
User’s Manual PLUG AND PLA Y Plug & Play DDC2B Featur e This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional inform ation about its display capabilities.
User’s Manual TECHNICAL SUPPOR T (F AQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position. *Power Cord should be connected. No Plug & Play *Check if the PC system is Plug & Play compatible.
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector ’ s screws. 2. Check the signal-cable’ s connection pins for damage.
User’s Manual 28 1400×1050 @60Hz 65.317 59.978 29 1440×900 @60Hz 55.469 59.901 30 1440×900 @60Hz 55.935 59.887 31 1440×900 @75Hz 70.635 74.984 19.
User’s Manual APPENDIX SPECIFICA TIONS Driving system TFT Color LCD Size 17” LCD Panel Pixel pitch 0.255mm(H) x0.255m m(V) H-Frequency 24 KHz – 80 KHz V ideo V -Frequency 55Hz– 75Hz Display Colors 16.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hanns.G HW173DBB è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hanns.G HW173DBB - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hanns.G HW173DBB imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hanns.G HW173DBB ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hanns.G HW173DBB, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hanns.G HW173DBB.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hanns.G HW173DBB. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hanns.G HW173DBB insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
