Manuale d’uso / di manutenzione del prodotto G1024 del fabbricante Grizzly
Vai alla pagina of 35
- 1 - IMPORTS, INC. 3 / 4 H.P. SHAPER MODEL G1024 INSTRUCTION MANUAL COPYRIGHT © 1994 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED JUNE, 1994.
- 2 - TABLE OF CONTENTS PAGE I. INTRODUCTION ..........................................................................................................1 II. COMMENTARY ...................................................................................
I. INTRODUCTION We are proud to offer the Model G1024 Shaper. The Model G1024 is part of a growing Grizzly fam- ily of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to cus- tomer satisfaction.
The information in this manual has been obtained from sources believed to be reliable and as up-to- date as possible. While this manual is intended to be a substantial source of basic shaping infor- mation, it is by no means the last word on shaping.
- 5 - 5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 6. AVOID DANGEROUS ENVIRONMENTS. Do not use power tools in damp or wet locations or expose them to rain. Keep your work area well lighted. 7. KEEP CHILDREN AND VISITORS AWAY.
22. NEVER LEAVE THE TOOL RUNNING UNATTENDED - TURN POWER OFF. Do not leave the tool until it comes to a full stop. 23. DRUGS, ALCOHOL, MEDICATION. Do not operate the tool under the influence of drugs, alco- hol, or any medication. Never operate machinery when overly fatigued.
V. PIECE INVENTORY Take a quick inventory of the parts and put them aside for assembly later. Since the majority of the shaper is pre-assembled at the factory, there aren’t a lot of items to inven- tory.
VI. CLEAN-UP BEFORE ASSEMBLY All of the unpainted surfaces on this machine – and a few of the painted ones – are coated with a preservative oil, called Cosmolene, which prevents rust and corrosion during shipping.
VIII. ELECTRICAL SERVICE REQUIREMENTS The Grizzly Model G1024 Shaper is furnished with a complete electrical package: A 3450 RPM TEFC 3 / 4 H.P. motor, ON-OFF starter switch, FORWARD/REVERSE switch and a cord set. The motor is single phase and may be operated on 220/240V, as well as 110/120V.
IX. ASSEMBLY Figure 3 Carefully lift the Model G1024 Shaper from its packaging. Be sure to get plenty of help when attempt- ing to lift or move the machine. The Model G1024 Shaper has a shipping weight of more than 150 lbs. Make sure you have plenty of help when it comes time to move the machine.
A. STAND The Model G1024 Shaper features an A-frame stand. Begin assembling the stand by attaching the four rubber feet to the bottom of the side panels with the M6-1.0x12 hex bolts, M6-1.0 hex nuts and 3 / 8 " flat washers provided. See Figure 4.
- 10 - B. FENCE ASSEMBLY The Model G1024 Shaper comes with a two-piece adjustable fence. Before attaching the fence unit to the shaper table, you will want to “wood” it.
C. SAFETY GUARD The Model G1024 features a clear acrylic safety guard which is designed to deflect wood chips away from the machine’s operator. To attach the guard, slip the support rod into the hole provided in the bracket bolted to the back of the shaper table.
X. SAFETY PROCEDURES This tool is capable of causing serious injury if used recklessly. This doesn’t mean that the machin- ery should be feared, but it does deserve a healthy respect for its power and potential danger. At the beginning of this manual we shared some general safety procedures with you.
14. HAND SAFETY. Never pass your hands directly over, or in front of the cutter. As one hand approaches the 12-inch radius point, move it away from the cutter to the outfeed side and repo- sition the hand at least 12 inches beyond the cutter. 15. STOCK FEED.
20. STOCK CONDITION. The danger of experiencing kick-back is increased when the stock has knots, holes, or foreign objects in it. Warped stock should be run through a jointer before attempting to run it through a shaper. 21. MISUSE. Do not use the Model G1024 for anything other than its intended purpose.
XI. ADJUSTMENT SECTION Any adjustments or maintenance performed on the Model G1024 should be done with the power off, the plug disconnected from the power source and only after all moving parts have come to a com- plete stop. Make sure the machine is level and secure.
- 16 - Outfeed Fence Cutter Rotation Workpiece Infeed Fence Feed Direction Improper Fence Adjustment Figure 11 When the shaping operation removes the entire face of the workpiece, the shaped surface will not be supported by the outfeed fence when the fences are paralleled, or mis-aligned, as shown in Figure 11.
- 17 - C U T T E R Feed Direction Workpiece Cutter Rotation Outfeed Fence Infeed Fence Figure 13 Take your time when adjusting the fence. Always use a piece of scrap wood to make a first run sam- ple. Micro-adjust accordingly. Double check yourself to make sure all hold-down devices are secure.
C. SPINDLE ELEVATION The Model G1024 Shaper features a locking spindle which can be adjusted for up to 7 / 8 " of vertical movement. To adjust the height of the spindle: 1.
- 21 - XII. RUB COLLARS Rub collars are used when shaping curved or irregular workpieces, such as arched doors or round table tops. They also allow you to perform freehand work. There are two types of rub collars; solid and ball-bearing. Don’t confuse spacers with solid rub col- lars.
B. EXAMPLES Rub collars may be used in any of the following positions: 1. Below the cutter. 2. Above the cutter. 3. Between two cutters. Suppose you want to mill a 3 / 8 " x 1 / 2 " rabbet. You must have a sufficient amount of uncut wood to provide adequate contact with the rub collar.
Spindle Assembly Table Table Rub Collar Spindle Nut Workpiece Cutter Figure 18 When the collar is used above the cutter, as shown in Figure 18, the cut cannot be seen. Yet, this offers some advantage in that the cut is not affected by slight variations in the stock.
C. PATTERN WORK When using a pattern, the rub collar can be positioned either above, below, or in-between cutters. See Figure 20. The pattern is usually used when the entire edge is to be shaped or when many duplicate pieces are needed.
5. Position the fences for your desired depth of cut. See the fence adjustment section for details. 6. Use a hold-down, or other safety device. See Figures 21 and 22.
B. IRREGULAR SHAPING Irregular or freehand shaping takes a high degree of skill and dexterity. This is where the real appli- cation of the shaper comes into focus. The fence assembly is not used in irregular shaping, so rub collars must be used. Choose the correct diameter for the appropriate depth of cut.
5. Insert a starting pin into the table surface, using the pin location that best supports your work. 6. Inspect your stock or pattern for any irregularities that might transfer to the cut. 7. Use some type of hold-down fixture and guard when doing freehand work.
Figure 25 When making a pattern, jig, or fixture, here are a few things to consider: 1. Use a material that will smoothly follow the rub collar or fence. 2. Make the fixture stable. Use proven methods and materials. 3. Fasten hand holds for operator comfort and safety.
XIV. EQUIPMENT MAINTENANCE Your Model G1024 Shaper requires very little maintenance. A thorough cleaning, now and again, will increase the machine’s durability and efficiency, by removing dust and grime that can gum up mov- ing parts. Sharp cutting surfaces are essential for top performance.
XVI. MACHINE DATA GRIZZLY MODEL G1024 3 / 4 H.P. SHAPER Design Type ....................................................................................................................Floor Model Overall Dimensions: Table .............................
XVII. WARRANTY AND RETURNS LIMITED WARRANTY Grizzly Industrial, Inc. warrants every product it sells for a period of one year on all parts and one year on all electric motors to the original purchaser from the date of purchase.
- 32 - XVIII. PARTS LISTS AND DIAGRAMS A. MAIN BODY ASSEMBLY 8 10 109 110 9 107 108 7 1 2 3 4 5 6 113 11 114 12 18 15 13 16 20 23 106 105 19 14 17 21 22 104 97 98 99 112 100 101 102 103 95 94 92 91 82.
- 33 - 001 P1022003 Side Panel 002 P1024002 Tie Bar 003 PB02M Hex Bolt M6-1.0x12 004 P1024004 Rubber Foot 005 PW02 Flat Washer 3 / 8 " 006 PN01M Hex Nut M6-1.0 007 PW02 Flat Washer 3 / 8 " 008 PN03M Hex Nut M8-1.25 009 PCB01M Carriage Bolt M8-1.
- 34 - 075 P1026223 Safety Washer 076 P1024076 Cutter Spindle 077 P1024077 Bearing Cover 078 P1024078 Spindle Cartridge 079 P1024079 Steel Ball 080 PR23M Retaining Ring 40mm 081 P6203 Ball Bearing 082 P1024082 Spindle Housing 083 P1024083 Bearing Cone 084 P1024084 Coil Spring 085 PSS20M Setscrew M8-1.
XIX. USING THE MODEL G1793 ROUTER BIT SPINDLE - 35 - The Model G1793 Router Bit Spindle is a handy accessory available for your Model G1024 shaper, which allows you to use your standard router bits as shaper cutters. Using the optional router bit spindle does require some minor modifications to the Model G1024.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Grizzly G1024 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Grizzly G1024 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Grizzly G1024 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Grizzly G1024 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Grizzly G1024, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Grizzly G1024.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Grizzly G1024. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Grizzly G1024 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
