Manuale d’uso / di manutenzione del prodotto EXT-HDMI1.3-242 del fabbricante Gefen
Vai alla pagina of 18
® 2x2 Switcher for HDMI ® 1.3 EXT-HDMI1.3-242 User Manual www.gefen.com.
ASKING FOR ASSIST ANCE Rev B4 T echnical Support : T elephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 T echnical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday PST Write T o: Gefen, LLC. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 9131 1 www .
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Panel Layout 5 Panel Descriptions 6 Connecting And Operating The 2x2 Switcher For HDMI 1.3 7 IR Remote Control Description 8 IR Remote Installati.
1 INTRODUCTION Congratulations on your purchase of the 2x2 Switcher for HDMI 1.3. Y our complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
2 READ THESE NOTES BEFORE INST ALLING OR OPERA TING THE 2X2 SWITCHER FOR HDMI 1.3 • By default, display information from the display connected to HDMI output port 1 is sent back to the source. Therefore, the other display connected to the 2x2 Switcher for HDMI 1.
3 FEA TURES HDMI Features • 225 MHz (up to 12 bit YUV 444 supported @ 1080p) • Deep Color • Dolby T rueHD and DTS-HD Master Audio • Lip-Sync • CEC Pass-Through Features • Easily switch bet.
4 P ANEL LA YOUT Front Panel Back Panel 1 2 3 4 5 6 7 8 9 10 11.
5 P ANEL DESCRIPTIONS 1 Power LED Indicator This LED will become active once the included 5V DC power supply is properly connected between the unit and a open wall power receptacle. 2 IR (Infrared) Receiver This receiver will accept command for switching between input HDMI devices using the included RMT -2IR remote control.
6 How to Connect the 2x2 Switcher for HDMI 1.3 1. Connect up to two HDMI source devices to the 2x2 Switcher for HDMI 1.3 using the supplied HDMI cables. 2. Connect up to four HDMI capable devices to the 2x2 Switcher for HDMI 1.3 using the supplied HDMI cables.
7 IR REMOTE DESCRIPTION 1 LED Button Press Indicator This LED will be activated momentarily each time a button is pressed. 2 Display and Source Selection Buttons These buttons are used to select which source is routed to the displays. Example: Route the source connected to Input 2 to the displays connected to Output 1 and Output 2.
8 Installing the IR Remote Control Battery 1. Remove the battery cover on the back of the IR Remote Control unit. 2. Insert the included battery into the open battery slot. The positive (+) side of the battery should be facing up. 3. Replace the battery cover .
9 IR REMOTE CONFIGURA TION Setting the IR Remote Channel on the RMT -8IR In the event that IR commands from other remote controls con fl ict with the supplied IR Remote Control Unit, changing the remote IR channel will fi x this issue. The IR Remote Control Unit has a bank of DIP switches for setting the Remote IR channel.
10 IR CHANNEL CONFIGURA TION Setting The IR Channel Use the following procedure to set the proper IR channel on the 2x2 Switcher for HDMI 1.3. 1 Press and hold the EDID button.
11 EDID MANAGEMENT EDID Mode Selection 1. EXTERNAL MODE : See page 10 for details on using the External EDID. 2. INTERNAL MODE : T o use this mode, press the EDID button on the rear panel until the front- panel LED marked “Int” turns bright green.
12 EDID MANAGEMENT External EDID Management The 2x2 Switcher for HDMI 1.3 features EDID Management. Before the source can send video or audio signals, the source device reads the EDID (Extended Display Identi fi cation Data) from the output devices connected to the Splitter .
13 Video Ampli fi er Bandwidth ............................................................... 225 MHz Input Video Signal ............................................................................ 1.2V p-p Input DDC Signal .........................
14 W ARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is noti fi ed within two (2) years .
Rev B4 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www .gefen.com support@gefen.com Pb This product uses UL listed power supplies.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Gefen EXT-HDMI1.3-242 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Gefen EXT-HDMI1.3-242 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Gefen EXT-HDMI1.3-242 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Gefen EXT-HDMI1.3-242 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Gefen EXT-HDMI1.3-242, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Gefen EXT-HDMI1.3-242.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Gefen EXT-HDMI1.3-242. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Gefen EXT-HDMI1.3-242 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
