Manuale d’uso / di manutenzione del prodotto F221m del fabbricante Ericsson
Vai alla pagina of 59
User guide F221m terminal Fixed Cellular T erminal for r esidential applications.
User guide F221m terminal Fixed Cellular T erminal for r esidential applications.
.
Content F221m ....................................................................... 7 SUPPLIED P AR TS................................................... 7 EXTERNAL CONNECTORS AND LIGHT INDICA T ORS ..................................................
V oice mail ................................................................. 29 Sending tone signals ................................................. 29 Controlling call time (minute minder) ..................... 29 Emergency number (hot line)......
Battery information................................................... 51 Disposing of the battery ........................................... 52 Moving or storing the FCT ...................................... 52 Accessing the battery compartment ...
Ericsson F221m First edition, February 2002 This manual has been published by Ericsson España, S.A. Bilbao T echnology Centre, without any warranty . Improvements and changes to this manual needed by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Ericsson España, S.
F221m The F221m is the best quality solution for providing access to fixed services either when no traditional fixed infrastructure is available or if an additional phone line is required.
External connectors and light indicators SIM card Y our network operator provides you with a SIM (Subscriber Identity Module) card. The SIM card contains information about your telephone number and the services included in your subscription, among other things.
Connections W arning!: please, before you start any connections refer to section “Safe and Efficient Use” on page 49 in this guide and contact your network operator if you have any questions.
The FCT is also equipped with an RS232 port that enables you to use it as a GSM modem for PC fax, data and SMS services. For this specific configuration, please refer to the FCT Data Reference Manual .
Connect a telephone to the FCT Connect a fixed telephone to the FCT telephone line. Important: you will use this telephone to dial the PIN. Switch on the FCT Connect the power supply . The FCT switches on automatically and the green and red light indicators start flashing.
Network search After you have switched on your FCT and entered the PIN, the FCT automatically searches for a network. Note: if the r ed light is off, ther e is a pr oblem with the power supply . See “T roubleshooting and FCT indicators” on page 33.
• Do not install the FCT on walls or rooms that contain large amounts of metal, steel or wiring. • Do not expose the FCT to extreme temperatures (near radiators, cooling vents, etc). If you experience poor reception quality , an outdoor antenna may result in improvement.
W arning!: once you have fixed the FCT to the wall and switched it on, check the final status of the red and green lights. If either one is off, there is a problem with the power supply or the GSM signal. See “T roubleshooting and FCT indicators” on page 33.
Note: it is str ongly r ecommended that the telephone wir e is installed indoors in or der to avoid lightning damage. Note: the telephone wir e should not exceed 600 meters.
Using telephones Fixed telephones connected to the FCT telephone line work in the same way as if they were connected to a fixed network. W arning!: you will not be able to make or receive data or fax calls while a speech call is ongoing. Note: you can also benefit from some FCT functionality that you do not usually have on your fixed network.
Using CLI displays Devices that display the incoming number (telephones with display , external displays, etc.) can be directly connected to the FCT line interface in the same way as an ordinary telephone.
Using fax machines The FCT terminal allows the connection of Group 3 analog faxes to the FCT telephone line, in the same way as a telephone. W arning!: the fax communication service has to be registered with your network operator . Otherwise, the network will not allow faxes to be sent or received .
Using PCs Analog modems connected to the FCT telephone line work in the same way as if they were connected to the fixed line. In this way , you can use your PC standard modem to make data calls (Internet browsing, e-mail, etc.
optionally , to improve the Internet connection, a DNS address and a Pr oxy address . All these settings will allow you to configure the Dial-up Networking program in your PC in order to establish a GPRS connection. Note: this pr ocedur e is similar to the way you configur e an Internet connection fr om a specific ISP (Internet Service Pr ovider).
send the CNG tone so that the data call is made automatically by the FCT . Incoming data calls are received in the same way as using the fixed line. Note: if you have a SIM car d that does not support separate voice and data numbers, the FCT does not r ecognize the type of incoming call.
Advanced features If a DTMF telephone is connected to the FCT , the following features can be accessed. Changing volume During a call, you can increase or decrease the reception volume level.
T o manage diversion of calls … With Function … Dial … Y ou will hear… Activate **21*Phone_number# 1 beep Always Deactivate ##21# 3 beeps Check status *#21# 1 beep if activated 3 beeps if deac.
Restricting calls (call barring) Y ou can restrict certain types of calls that can be made or received. Y ou need a password to turn a call restriction on or off.
All outgoing international calls except your home country All incoming calls when you are abroad T o manage restriction of calls … W ith Function … Dial … Y ou will hear… Activate *33*Password.
Note : if instead of hearing beeps you hear a deep tone, this means that ther e has been an err or in the activation or deactivation. More than one call (call wait, call hold, call transfer , multiparty call) Y ou can handle more than one call simultaneously .
• T o ignore the waiting call, take no action. • T o continue with the ongoing call and reject the waiting call (give a User Busy indication tone to the waiting call): press R0.
Phonebook (abbreviated dialing) Y ou can store telephone numbers in either the SIM card memory or the FCT memory . Up to 99 telephone numbers can be stored in each of them. The following table shows how to manage the phonebook with the 99 memory positions (Pos).
V oice mail The answering service of your network allows callers to leave a voice message when you cannot answer your calls. If you have voice mail, you will hear 3 beeps before the dial tone, as soon as you pick up the receiver to make a call.
T o manage the hot line … Dial … Y ou will hear… Activate **53*Phone_number**timer# 1 beep Deactivate #53# 3 beeps service *#53# 1 beep if activated 3 beeps if deactivated service and *#53*Phone.
T o manage alternate line Dial … Y ou will hear… service function … Activate Line 1 **591# 1 beep Activate Line 2 **592# 1 beep Check status Line 1 *#591# 1 beep if activated 3 beeps if deactiva.
T o unblock your SIM card while changing your PIN In order to unblock your SIM card and change the PIN at the same time, please dial the following sequence: **05*PUK*NEW_PIN*NEW_PIN# 32 Advanced featu.
T r oubleshooting and FCT indicators This chapter describes the procedures to identify and, if possible, correct problems that might occur with the FCT or its installation. Some problems require that you call your network operator , but most problems you encounter you can easily correct yourself.
34 T roubleshooting and FCT indicators Alarm status ENTER PIN ENTER PUK INSER T SIM SIM ERROR WRONG NETWORK WRONG SUBNETWORK WRONG SIM FCT LOCKED WRONG XXX CK (where XXX is the name of the specific pa.
T roubleshooting and FCT indicators 35 If you see… Red light ON Green light ON or flashing Both lights OFF Red light ON Green light OFF Red light Flashing Green light ON or flashing (not simultaneou.
Audible tones The FCT generates audible tones in your telephone set, thus providing the same service characteristics as the one given by the traditional fixed network. The following table describes the nature of the main tones you will get when using the unit.
FCT technical data GSM AIR INTERF ACE Fr equency Bands: T riple-Band E-GSM 900, GSM 1800 and GSM 1900 E-GSM 900 Frequencies: TX 880-915 MHz, RX 925-960 MHz RF power: Maximum 2 W (33 dBm), Power class .
RS232 INTERF ACE • Data services: all applicable GSM 7.07 A T commands • SMS: all applicable GSM 7.05 A T commands ANTENNA (included) • Frequency Bands: T riple-Band E-GSM 900, GSM 1800 and GSM .
Accessories The F200 series terminals benefit from a wide range of accessories, which ensure the best and easiest way to install, serve and maintain the terminals, enhancing their functionality . Only these approved-by-Ericsson accessories will guarantee the quality and performance of the terminals.
AA batteries holder (size: 99.01 mm x 51.69 mm) is provided. NiMH or NiCd rechargeable AA batteries can also be used with these accessory , but these batteries must be charged using an external char ger . W arning!: Ericsson recommends precaution when handling lead-acid batteries, and also special attention over storage and power loss issues.
Annex: PC data configurations Windows 98 GPRS set-up W arning!: your PC must have the Dial-up Networking and the TCP/IP protocol installed within the network components. Y ou can check this in ‘Start->Settings->Control Panel’ and double clicking on ‘Network’.
4) Click on ‘Finish’. 5) In the ‘Dial-Up Networking’ folder, right-click on the created connection and select ‘Properties’. 6) In the ‘General’ tab, turn off ‘Use area code and Dialing Properties’.
8) Push the ‘TCP/IP Settings…’ button. – ‘Server assigned IP address’ must be checked . – ‘Server assigned name server addresses’ must be set if the network operator requires it. If the network operator provides DNS addresses , then these must be added once ‘Specify name server addresses’ is marked.
Y ou have now installed the GPRS connection. T o connect to the GPRS network, follow steps 1 to 3: 1) Go to ‘My Computer ’-> Dial-Up Networking’ and open the previously configured connection. 2) T ype the user name and password provided by your network operator and verify that the telephone number is *98#.
T o configure your GPRS connection under a W indows NT PC, follow steps 1 to 8: 1) Go to ‘My Computer ’ and double-click ‘Dial-Up Networking’. 2) If there are no previously configured connections, the following wizard will show up.
5) In the ‘Server ’ tab select ‘PPP: W indows NT , W indows 95 Plus, Internet’ from the ‘Dial-up server type’ list. Be sure that ‘TCP/IP’ is the only ticked protocol within the ‘Network protocols’ box. 6) Push the ‘TCP/IP Settings…’ button.
– ‘Use IP header compression’ optional. – ‘Use default gateway on remote network’ turned on . 7) Press ‘OK’ and go to the ‘Security’ tab. Select ‘Accept any authentication including clear text’. 8) Click ‘OK’ all the way to update the configuration.
2) T ype the user name and password provided by your network operator . If a ‘Domain’ field is present, then leave it blank. 3) Once you are connected, you may use your connection as an ordinary Internet connection.
Safe and efficient use Note: please r ead this information befor e using your FCT . Save this user guide since it contains important safety information and operating instructions. Product car e • Do not expose your FCT to liquid or moisture. • Do not expose your FCT to extreme high or low temperatures.
Radio frequency energy Y our FCT is a radio transmitter and receiver . When the FCT is turned on, it receives and transmits radio frequency (RF) energy . The system that handles your call when you are using your FCT controls the power level at which your FCT transmits.
Power supply • Ensure that your AC power outlet is adequately grounded, that it is situated near the FCT and it is easily accessible. • Connect the power supply cord only to the AC power outlet that meet the specifications marked on the FCT power supply .
• Do not expose the battery to extreme temperatures, never above +60°C. For maximum battery capacity , use the battery in room temperature. • Do not let the metal contacts on the battery touch another metal object. This could short-circuit and damage the battery .
Limited warranty Limited warranty conditions Thank you for purchasing this Ericsson Product. T o get the maximum use out of your new product, we recommend that you follow a few simple steps: • Read the Guidelines for safe and efficient use. • Read all of the terms and conditions of the Ericsson W arranty listed below .
2. Any repair or replaced Product will be warranted for the remainder of the original warranty period. Repair or replacement may be via functionally equivalent reconditioned units. Replaced faulty parts or components will become the property of Ericsson.
Regulatory information Declaration of Conformity W e, Ericsson Radio Systems AB of Kistagången 26, Kista S-16480 Stockholm, Sweden declare under our sole responsibility that our product Ericsson type 0130101-BV and in combination with our accessories, to which this declaration relates is in conformity with the appropriate standards 3GPP TS 51.
Definitions The following definitions are supplied in order to better understand certain concepts included in this manual: Switch-on : power up the FCT by connecting the AC power supply or a charged battery . Switch-off : power down the FCT by disconnecting the AC power supply or removing the battery .
.
V V i i s s i i t t u u s s o o n n o o u u r r w w e e b b s s i i t t e e : : h h t t t t p p : : / / / / w w w w w w . . e e r r i i c c s s s s o o n n . . c c o o m m / / w w i i r r e e l l e e s s s s / / p p r r o o d d u u c c t t s s / / f f i i x x e e d d Ericsson España, S.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ericsson F221m è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ericsson F221m - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ericsson F221m imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ericsson F221m ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ericsson F221m, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ericsson F221m.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ericsson F221m. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ericsson F221m insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
