Manuale d’uso / di manutenzione del prodotto 5.0 del fabbricante Eltax
Vai alla pagina of 20
O p e r a t i o n M a n u a l D AB-50 DAB/FM T uner.
01 ACCESSORIES Accessories 1 x DAB-50 1 x Remote control 2 x Batteries (Optional) 1 x DAB/FM Antenna (Optional) 1 x Operation Manual This operation manual supplies all the information that you need to have about your T angent DAB-50.
02 CONTENTS ACCESSORIES Accessories 01 CONTENTS Contents 02 SAFETY PRECAUTIONS Safety precautions 03 IMPORT ANT SAFETY INSTRUCTIONS Important safety instructions 04 IMPORT ANT INFORMA TION Important i.
TO MINIMISE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE. DO NOT OPEN THE CABINET AS IT CONT AINS DANGEROUS VOL T AGE.
W ARNING: IT IS IMPORT ANT THA T YOU READ AND OBSERVE BOTH THE INSTRUCTIONS IN THIS MANUAL AND THE INSTRUCTIONS ON THE UNIT . KEEP THIS MANUAL FOR FUTURE REFERENCE. This unit was designed and manufactured with a view to providing maximum safety for the user .
Service Do not attempt to carry out any service work yourself. By opening or removing the cabinet, you will be exposed to dangerous voltage or other hazards.
IMPOR T ANT INFORMA TION Handling instructions The top and back panel of the unit may become warm after prolonged use. This is not due to a defect. T urn off the power when the unit is not used.
07 CONNECTION Connection to the mains Do not turn on the power before all connections have been made correctly . Check that all connections have been made correctly before turning on the power . Check that the mains voltage is 230-240V AC50Hz before turning on the power.
08 REMOTE CONTROL Installation of batteries Remove the cover as illustrated. Position two batteries of the type AAA/R03/UM4 in the battery compartment. Make sure that the orientation of the batteries is correct (see drawing at bottom). Replace the cover .
09 Some of the functions of the unit can only be performed by means of the remote control. Some functions are connected with the selected signal input source. Some buttons on the remote control may therefore not be available if the corresponding signal input source has not been selected.
8 9 1 0 1 2 3 4 5 6 7 10 FRONT P ANEL AND CONNECTIONS Front panel Mains switch: Used to interrupt the mains voltage. LED indicator: Lights green when the unit is turned on. Lights red when the unit is in standby mode or in operation. Preset no. 1: Selects the station saved under no.
1 1 FRONT P ANEL AND CONNECTIONS Connections 1 2 3 4 5 Stereo Output: Analogue stereo output. For connection to stereo amplifier or receiver with analogue input. Optical Output : Optical SPDIF output. For connection to stereo amplifier or receiver with digital input.
12 CONNECTION Audio connection layout Subwoofer (Optional) PHON O TUNER DVD CD AUX 1 AUX 2 FUNC TION VOLU ME POWE R HEAD PHON E AMP- 50 AMPL IFIE R Analog amplifier/receiver PHON O TUNER DVD CD AUX 1 .
13 Op ti c al O ut pu t An te n na C on tr a st Op ti c al O ut pu t An te n na C on tr a st For an optimal result it is recommended to install a DAB antenna on the roof or on the loft. The supplied antenna must be adjusted for the best possible result by means of the signal bar described above.
14 PH ON O PO WE R DA B- 50 D AB /F M TU NE R 1 3 3 T urn on the unit by pressing the mains switch. Press the standby button on the remote control to switch to standby mode. The display will turn of f and all functions will be reduced to a minimum to make sure that the unit uses minimal power .
15 OPERA TION AND FUNCTIONS DAB tuning When the unit is turned on for the first time, all settings will be default settings. The settings can be changed according to your preference. When the unit is turned off the next time, these settings will naturally be saved as the new default settings.
16 OPERA TION AND FUNCTIONS FM tuning The DAB-50 offers both manual and automatic tuning on the FM band. This makes it possible to save just one specific channel.
17 TROUBLESHOOTING T roubleshooting PROBLEM CAUSE/REMEDY No power when the unit is turned on. - Switch on the electric current at the socket. - Check that the plug has been correctly inserted into the socket. - The internal fuse has blown and must be replaced by a qualified service technician.
18 TECHNICAL DA T A T echnical data RF section: T uner bands DAB 174-240MHz (Band III) FM 87.5-108.0MHz Sensitivity -96dBm type Display: 2 lines of 16 characters LED backlight Presets 4 Audio outputs Stereo, 2.
www . .c om tangent - audio.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Eltax 5.0 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Eltax 5.0 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Eltax 5.0 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Eltax 5.0 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Eltax 5.0, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Eltax 5.0.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Eltax 5.0. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Eltax 5.0 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
