Manuale d’uso / di manutenzione del prodotto 900TL del fabbricante Digital Media
Vai alla pagina of 15
EK–DTMAU–IN. A01 DECmau 900TL INST ALLA TION The DECmau 900TL is a T oken Ring Multistation Access Unit (MAU). As a member of Digital’s T oken Ring product family , it operates in a DEChub 900 MultiSwitch, or a single-slot hub (DEChub ONE MAU 900TL).
FCC NOTICE – Class A Computing Device: This equipment generates, uses, and may emit radio frequency energy . The equipment has been type tested and found to comply with the limits for a Class A comp.
PK–02586–IL 1 ) Power LED. Lights when the MAU has power . 2 ) Module OK LED. Lights when the MAU passes its self-test. If the MAU fails its self-test, the OK LED is off. 3 ) Ring A/B LEDs. In a hub, either the A LED or the B LED is on to show the ring.
Note: The rear panel shown here is used only when the MAU is in a single-slot hub configuration. 1 ) Ring In LED. Lights with a Ring In connection. 2 ) Ring Out LED. Lights with a Ring Out connection. 3) Power Connector . Provides power connection for the MAU.
a. Loosen the screw on the single-slot hub until it disengages. b. With one hand holding the front of the MAU, and your other hand holding the single-slot hub, carefully pull the two units apart. When you install a MAU in a DEChub 900 MultiSwitch, you do not have to turn off the hub power .
Connect station cables to any available lobe connector on the MAU. For 150-ohm applications, you also need an impedence matching transformer cable (Digital part number BN26T -03). Connect station cables. 4 PK–02570–IL Installing a MAU in a DEChub 900 MultiSwitch (continued) 6 DECmau 900TL V erify power .
a. Set the Ring In and the Ring Out Autowrap switches to 1 or 0. b. Set the switch to 1 to enable Autowrap when the Ring In or Ring Out port connects to a device with Digital’s Auto wrap, there is only one MAU in the network, or the port is not connected to the network.
If a MAU is being added to an existing network, connect Ring In to the Ring Out connector of a MAU or repeater , and connect Ring Out to the Ring In connector of a MAU or repeater . Connect station cables. 4 Check LEDs. 6 With power on, verify that the Power and Module OK LEDs are on.
Removing a MAU from a DEChub 900 MultiSwitch a. Lift up the Release lever on the hub. b. Pivot the MAU back on its bottom mounting tab until it disengages from the hub. DECmau 900TL 9 Note: When you remove a MAU from the hub, do not turn off the hub power .
LED Summary LED 1 Off On Flashing Power No Power Power OK Module OK Self-test failed Self-test OK or not operating 4/16 Mb/s No activity V alid speed or management set speed Lobe Inactive Connected to network Continuous single flash: network management disabled port.
Cabling T able 1 lists the T oken Ring industry guideline for the maximum lobe length of shielded twisted-pair (STP) and unshielded twisted-pair (UTP) cable. T able 1 Industry Lobe Length Guideline Lobe lengths for Digital’s MAUs exceed the industry guideline.
Cabling (continued) Digital recommends that you use repeaters to segment the ring in a network with multiple wiring closets. In some situations, only one, or no repeaters, are required. Refer to the appropriate T oken Ring repeater manual for specific information.
Problem Solving If ... Then ... Do This ... DEChub 900 MultiSwitch and DEChub ONE Power LED is off. MAU does not have power . V erify that outlet has power . Check power connection to MAU. Replace power supply . Replace MAU. Module OK LED is off. MAU failed self-test.
Problem Solving (continued) If ... Then ... Do This ... DEChub 900 MultiSwitch ONL Y Lobe, Ring In, Ring Out, Network management has T o change settings, you can use Ring A/B LEDs flash together . disabled MAU. network management commands or the MAU’s Reset switch.
Product Specifications Product Specification In a Hub DEChub ONE Size 27.3 x 1 1.2 x 3.2 cm 27.3 x 17.0 x 3.2 cm (10.8 x 4.4 x 1.2 inches) (10.75 x 6.7 x 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Digital Media 900TL è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Digital Media 900TL - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Digital Media 900TL imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Digital Media 900TL ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Digital Media 900TL, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Digital Media 900TL.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Digital Media 900TL. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Digital Media 900TL insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
