Manuale d’uso / di manutenzione del prodotto IE301016S8PC del fabbricante Cisco Systems
Vai alla pagina of 26
1 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide • About this Guide • Box Contents • Running Express Setup • Managing t he Switch • Install.
Cisco IE 3010 Switch Getting Started Guide 2 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 About this Guide This guide describes ho w to use Express Setup t o initially conf igure your Cisco IE 3010 switch.
3 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Box Contents 1 Cisco IE 3010 1 switch 1. Cisco IE-3010-24TC shown .
Cisco IE 3010 Switch Getting Started Guide 4 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Running Express Setup Y ou should use Express Set up to enter the initial IP information. Y ou can then access the switch through the IP address for further config uration.
5 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Step 4 Approximately 45 second s after the switch po wers on, it begins t he power -on self-test (POST), which can take up to 5 minutes. s During POST , the SYSTEM LED blinks green, and the port LEDs turn green.
Cisco IE 3010 Switch Getting Started Guide 6 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Step 6 Connect a Category 5 or 6 cable to the blinking 10/100 Et hernet port. Connect the other end of the cable to the Ethernet port on your PC. W ait until the port LEDs on th e switch and your PC or lap top are either green or blinking green.
7 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Step 7 Start a browser session on the PC, open a well-known website, suc h as Cisco.com. The swit ch prompts you for the d efault username and passw ord.
Cisco IE 3010 Switch Getting Started Guide 8 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Step 8 Enter this information in t he Network Settings f ields: Note All entries must be in English let ters. • In the Management In terface (VLAN ID) f ield, the default is 1 .
9 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Managing the Switch After completing Express Setup and installing the switch in your network, you can use the CLI for further conf iguratio n . Y ou can enter Cisco IOS commands and parameters through the CLI.
Cisco IE 3010 Switch Getting Started Guide 10 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 3. Config ure the PC terminal emulation software for 9 600 baud, 8 data bits, no parity , 1 stop bit, and no flo w control. 4. Use the CLI to enter configuration comma nds.
11 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Note For IP-30 compliance: - Use the 16-14 A WG wire and appropriate termin als for the A C or high.
Cisco IE 3010 Switch Getting Started Guide 12 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 • Relati ve humidity around the switch does no t exceed 95 percent (noncondensing). • Altitude at the installation si te is not higher than 10,000 feet.
13 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide War ni ng T o prevent airflow restriction, allow clearanc e around the ventilation openings to be at least: 1.
Cisco IE 3010 Switch Getting Started Guide 14 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Rack-Mounting the Switch Use the four number -12 Phillips machine scre ws to attach the brackets to the rack. Use the black Phillips machine screw to att ach the cable guide to the left or right bracket.
15 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide . 1 Mid-mounting po sition 4 Number -12 Phillips machine scre ws 2 Black Phillips machine scre w 5 .
Cisco IE 3010 Switch Getting Started Guide 16 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Wiring the Power Source The switches have tw o power supply slot s to support these p ower supply m.
17 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Step 3 Insert the grou nd wire into the terminal lug, and crimp the terminal to th e wire. Step 4 Slide the ground scre w from Step 1 throug h the terminal lug.
Cisco IE 3010 Switch Getting Started Guide 18 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Connecting to the Power Source Prepare the po wer cable. War ni ng This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.
19 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Step 3 Use a Phillips scre wdri ver to loosen the capti ve screw on the po wer-in put terminal, and open th e c over. Step 4 Use twisted-p air copper wire (14- to 18-A WG) long en ough to connect from th e power -input terminal to the power source.
Cisco IE 3010 Switch Getting Started Guide 20 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Step 7 Loosen the terminal scre w , and slide the spade terminal under the screw and washer . Note Use the appro priate terminal screw s, depending on whether you are installing a high-v oltage (A C or DC) or a low-v oltage (DC) power supply .
21 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide DC power: Insert the positi v e wire into the terminal screw labeled + , and the negati ve wire into the terminal scre w labeled – . Make sure that you cannot see any wire lead.
Cisco IE 3010 Switch Getting Started Guide 22 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Connecting the Switch Ports 10/100 or 10/100/1000 Ports The 10/100 ports on the Ci sco IE-3010-16S-8PC support Po wer ov er Ethernet (PoE) and enhanced PoE (ePoE) .
23 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide SFP-Module Ports For a list of su pported modules, see the release notes on Cisco. com. For detailed instructions on installing, removi ng, and connecting to SFP modules, see the SFP module documentatio n.
Cisco IE 3010 Switch Getting Started Guide 24 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Troubleshooting Express Setup If Express Setup does not run or if the Exp ress Setup page does not .
25 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Resetting the Switch to the Default Settings Caution Resetting the switch deletes the configurati on and restarts the switch. 1. Press and hold the Express Setup button for about 10 seconds.
Cisco IE 3010 Switch Getting Started Guide 26 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 For More Information Go to Cisco.com: • Cisco IE 3010 Switc h Har dwar e Installation Guide • R.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cisco Systems IE301016S8PC è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cisco Systems IE301016S8PC - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cisco Systems IE301016S8PC imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cisco Systems IE301016S8PC ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cisco Systems IE301016S8PC, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cisco Systems IE301016S8PC.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cisco Systems IE301016S8PC. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cisco Systems IE301016S8PC insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
