Manuale d’uso / di manutenzione del prodotto EDD91 del fabbricante CDA
Vai alla pagina of 20
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
3 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services.
4 • Steam cleaners must not be used when cleaning this appliance. • The performance of your extractor will vary depending on a number of factors. These include: type of extraction, length of ducting, room volume, ventilation available and cleanliness of the filters.
5 Using Y our Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for appro ximately 15 minutes after the end of cooking.
6 T o decrease the speed at any time • T ouch the “-” key a few times, until the required speed is reached. T o switch o the extractor • T ouch the “O ” key : The moving panel will descend to its rest position and the appliance will continue extracting until its height drops below appro x.
7 Energy saving feature This extractor is fitted with an energy saving feature that automatically reduces the motor speed if it is left on the highest setting . When the motor speed is set to the fourth level, it will automatically switch to level three after six minutes of operation.
8 T o remove and replace the grease filters • T ouch the “On/+” key so the moving panel raises to its full extent, then isolate the power supply so it stays raised. • By pulling the two top corners of the front panel (Fig. 2) at the same time, it will be released and pivot toward you.
9 Mounting your Extractor When the extractor is to be installed behind an electric or gas hob, the minimum distance between the hob and extractor must ex ceed 50mm. In the case of a gas hob, the minimum distance from any burner to the back of the hob must also be 65mm.
10 T roubleshooting Y ou observe that Possible Causes What should you do ? The hood does not work. There ia a power outage. Check the power supply . The 9 pin connector is faulty or misconnected. Check the orientation and security of the 9 pin connector .
11 Ducting and V entilation • For best performance and lowest noise output, we recommend the use of 150mm ducting. Use of any smaller ducting will reduce performance and increase noise. • The length of ducting should not ex ceed 5 metres in total.
12 Installation Note • W e recommend that you seek the help of another individual when installing this product. • The fixings supplied are suitable for most installations. It is the responsibility of the installer to ensure that the fixings are suitable for the cabinets in the property .
13 2) Before making a cut-out in the kitchen cabinets or worktop, ensure that there are no structural (or other) obstructions that would hinder installation. Ensure that the cabinet dimensions are sucient to accommodate the extractor , allowing for the specified clearance between the final installed positions of the extractor and the hob.
14 6) L ocate the support frame (trim piece); apply a narrow bead of silicone sealant to the underside of this (Fig. 7). Position this around the cut-out in the worktop (Fig. 8). 7) L ower the main body of the downdraft extractor through the support frame and into its fitted position.
15 9) R efit the motor unit to the main body of the downdraft extractor . This may be positioned with the outlet facing vertically upward or downward.
16 14) Open the filter cover (Figs. 14 & 15) then remove the grease filter package identified in Fig. 15. 15) Position the grease filters as shown in Fig. 16. Downdraft Calibration After installation it is necessary to calibrate the downdraft mechanism.
17 Mains Electricity Connection W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 3Amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse.
18 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELL OW must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W .
19 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CDA reserve the right to change specifications without prior notice. Attribute Symbol Units Model Identification edd61 edd91 Annual Energy Consumption AEC Hood 54.
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www. cda.eu www .cda.eu Please contact our Customer Care Department for Service on the details below Customer Care Department The Group L td.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il CDA EDD91 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del CDA EDD91 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso CDA EDD91 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul CDA EDD91 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il CDA EDD91, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del CDA EDD91.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il CDA EDD91. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo CDA EDD91 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
