Manuale d’uso / di manutenzione del prodotto MA-600 del fabbricante Toshiba
Vai alla pagina of 191
PRINTED IN JAPAN TEC Electronic Cash Register MA - 60 0 SERIES Document No. EO3 - 11106 Original De c ., 2005 (Revised ) Programming Manual.
EO3 - 11106 TABLE OF CONTENTS Page 1. INTRODUCTION ......................................................................................................... 1 - 1 1.1 Main Features ......................................................................
EO3 - 11106 CAUTION! 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification. 3. Plea se refer to your local Authorised Service representative with regard to any queries you may have in this manual.
1. INTRODUCTION EO3-11106 1.1 Main Features 1- 1 1. INTRODUCTION This programming man ual is provided for salesperso ns, field engineers, and other personal as suppl ementary manual for TOSHIBA TEC Electronic Cash Register MA-600 series.
2. SPECIFICATIONS EO3-11106 2. SPECIFICATIONS 2- 1 2. SPECIFICATIONS SIZE: 410 mm (width) x 442 mm (depth) x 291 mm (height) (height including rubber feet) Height when the customer display is fully raised: 351 mm WEIGHT: Approximately 13.
2. SPECIFICATIONS EO3-11106 2. SPECIFICATIONS 2- 2 PAPER ROLL (RECEIPT and JOURNAL) Media ---------------------------------------------------- Ther mal roll paper Width ---------------------------------------------------- 58 +0/-1 mm Thickness----------------------------------------------- 0.
3. CAPACITIES EO3-11106 3.1 Indexing Capacities 3- 1 3. CAPACITIES 3.1 Indexing Capacities Input Item Digits Remarks Amount 7 Quantity in Multiplication 6 3 integer digi ts + 3 decimal digits (0.001 to 999.999) Unit Price in Multiplication 6 Tender Media Keys 8 Non-add Number 18 Percent Rate 5 2 integer digits + 3 decimal digits (0.
3. CAPACITIES EO3-11106 3.2 Basic Memory Capacities 3- 2 3.2 Basic Memory Capacities ( NOTE: For Item Count below, “6 + 2 digits” m eans that it has 6 integer digits and 2 decimal digits.
3. CAPACITIES EO3-11106 3.3 Financial Memory 3- 3 3.3 Financial Memory Daily GT Name of Total/Counter Counter Type Counter Digits Total Digits Counter Digits Total Digits Remarks GT (Grand Total) 16 (.
3. CAPACITIES EO3-11106 3.3 Financial Memory 3- 4 Financial Memory: (continued) Daily GT Name of Total/Counter Counter Type Counter Digits Total Digits Counter Digits Total Digits Remarks Cheque-in-dr.
3. CAPACITIES EO3-11106 3.3 Financial Memory 3- 5 Financial Memory: (continued) Daily GT Name of Total/Counter Counter Type Counter Digits Total Digits Counter Digits Total Digits Remarks Credit-in-drawer Difference 10 at Money Declaration Misc.
3. CAPACITIES EO3-11106 3.4 Cashier Memory 3- 6 3.4 Cashier Memory Daily GT Name of Total/Counter Counter Type Counter Digits Total Digits Counter Digits Total Digits Remarks GS (Gross Sale) ITEM 6 + .
3. CAPACITIES EO3-11106 3.4 Cashier Memory 3- 7 Cashier Memory: (continued) Daily GT Name of Total/Counter Counter Type Counter Digits Total Digits Counter Digits Total Digits Remarks Credit-in-drawer.
3. CAPACITIES EO3-11106 3.5 Others 3- 8 Cashier Memory: (continued) Daily GT Name of Total/Counter Counter Type Counter Digits Total Digits Counter Digits Total Digits Remarks Item Correct ENTRY 6 10 6 10 Item Correct on DP+/PLU+ Void ENTRY 6 10 6 10 Void on DP+/PLU+ Misc.
3. CAPACITIES EO3-11106 3.6 Memory Balance 3- 9 3.6 Memory Balance 1. GT (Grand Total) = Sum of Daily GS (Gross Sale) 2. NET GT = Sum of Daily Net Sales 3. NEG GT = GT – NET GT 4. GS (Gross Sale) = (Sum of Positive Depts) + (Sum of Add-on Taxes) NOTE 1 5.
4. SYSTEM START-UP PROCEDURE EO3-11106 4. SYSTEM START-UP PROCEDURE 4- 1 4. SYSTEM START-UP PROCEDURE Case 1: To start-up using the MA-600 terminal only RAM Clear (Chapter 5) All the programming opera.
4. SYSTEM START-UP PROCEDURE EO3-11106 4. SYSTEM START-UP PROCEDURE 4- 2 PC Transmission Information Setting Data transmission information setting with a PC connection is performed here.
5. RAM CLEAR, DATA CLEAR, STAT US CLEAR EO3-11106 5.1 RAM Clear 5- 1 5. RAM CLEAR, DATA CLEAR, STATUS CLEAR 5.1 RAM Clear CAUTION! This clear operation deletes all programmed data and sales data stored in the memory of the ECR. (i.e., the ECR goes back to initial status.
5. RAM CLEAR, DATA CL EAR, STATUS CLEAR EO3-11106 5.2 DATA Clear 5- 2 5.2 DATA Clear CAUTION! This clear operation deletes all sales data of any operation sequence stored in the memory of the ECR.
5. RAM CLEAR, DATA CL EAR, STATUS CLEAR EO3-11106 5.3 STATUS Clear 5- 3 5.3 STATUS Clear Performing the STATUS Cl ear operation will clear an error and th e key locked condition, however, the sales data and the programmed data will not be cleared by this operation.
6. TERMINAL FILE PROGRAMMING EO3-11106 6. TERMINAL FILE PROGRAMMING 6- 1 6. TERMINAL FILE PROGRAMMING Table of Terminal File Programming Operations Operation Condition (NOTE) Mode Lock Position Page I.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming 6- 2 6.1 Instructions for Programming On the MA-600 series adopting the LCD display, each pr ogramming operation is pe rformed by sele cting the corresponding menu item on the LCD display.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming 6- 3 6.1.2 Keyboard Lay out Variations The keyboard layout is automatically switched among th ree acco rding to operation to be performed (ordinary registration, read/reset, programming) when the M ode Lock is turned to the corresponding position.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming 6- 4 (2) Keyboard layout for programming Mode Lock Position: SET BLIND • Ordinary Type Keyboard ↑ Del History RF JF A F K P U ↓ ALL VOID C # B G L Q V ← Rtn 7 8 9 C H M R W → Dbl 4 5 6 D I N S X Enter A/a 1 2 3 E J O T Y PLU 0 00 .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming 6- 5 (3) Keyboard layout for Read/Reset Mode Lock Position: X Z • Ordinary Type Keyboard ↑ RF JF ↓ C # ← Rtn 7 8 9 → X 4 5 6 Enter 1 2 3 PLU 0 00 . ST AT/TL • Flat Type Keyboard RF JF ↑ ↓ ← → # C Rtn Enter 7 8 9 X 4 5 6 1 2 3 ST PLU 0 00 .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.1 Instructions for Programming 6- 6 6.1.2 Basic Key Functions 1. The following are main keys and their f unctions to be used in programming operations. (1) Keys for selecting items on the menu screen Key Function [ ↑ ] This key is used for moving the cursor upward.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 6- 7 3. To clarify the operation flow, definitions of keys of the ECR keyboard are as shown below. | | --------- Selective numeric value which is entered through the Numeric keys. [ ] ---------- Depression of the function key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 6- 8 6.2.1 Character Code Entry Method Character Code Table 1: Standard Characters 2 3 4 5 6 7 8 9 10 11 12 13 14 15 00 SP 0 @ P ` p € .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 6- 9 Character Setting Operations • To set a one-byte character, enter the COL (column) code and then the ROW code, followed by the [#] key. ex.) To set “%”, enter 205 and depress the [#] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 6- 10 6.2.2 Direct Character Entry Method Using Keyboard (installed as the ECR Main Keyboard): -- Keyboard layout for programming -- • Or.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 6- 11 Using PK-2 (PLU Keyboard; hardware option) The PK-2 keyboard is used for enteri ng a required PLU code by simply depressing the code-preset key on this keyboard in REG or MGR mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.2 Character Entries 6- 12 6.2.3 How to use the [History] key The [History] key is used for performing character ent ries with the name previously entered. Operation: [History] ( [ ↓ ] ) [Enter] 1) The [History] key depression will let the most recently pr ogrammed name displayed on the LCD display.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.3 Condition Required for Programming Operations 6- 13 6.3 Condition Required for Programming Operations “CONDITION” is given at the top of each programming operation. The E CR must satisfy this condition to perform programming operations.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.4 SFKC (Selective Function Key Code) Programming 6-14 6.4 SFKC (Selective Function Key Code) Programming SFKC Programming is to determine the keyboard layout with the required keys. T his operation must be performed first before any other prog ramming operation.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.4 SFKC (Selective Function Key Code) Programming 6-15 SFKC Table SFKC Key Name Memory to be opened (REMARKS) 0 Dead-key code (used to close the key and memory).
6. TERMINAL FILE PROGRAMMING EO3-11106 6.4 SFKC (Selective Function Key Code) Programming 6-16 SFKC Table (continued) SFKC Key Name Memory to be opened (REMARKS) 104 TRF (Transfer) No memory 105 to 10.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.4 SFKC (Selective Function Key Code) Programming 6-17 SFKC Receipt Sample Standard Keyboard (auto-set by RAM Clear) • Ordinary Type Keyboard LOG/ RECEIPT VAL.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-18 6.5 System Option Programming This operation is used to set the ECR’s basi c features and selective functions to meet the requirement of the market and your user. This programming operation is performed in SET mode or BLIND mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-19 Setting Example) To set Address No. 1 with the following requirements: (Refer to the Address No. 1 table on the subsequent page.) Bit No. 1: Time NON-PRINT (SET status) Bit No. 3: Subtotal NON-PRINT (SET status) Other bits will be selected to “RESET” status.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-20 (continued from the previous page) Operation LCD Display Remarks Depress the [ → ] key to select the status of Bit No. 1. The status of Bit No.1 is turned from N to Y . N: RESET status Y: SET status The numeric value 1 indicating the Bit No.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-21 Setting Example) To set Address No. 1 with the following requirements: (Refer to the Address No . 1 table on the next page.) Bit No. 1: Time NON-PRINT (SET status) Bit No. 3: Subtotal NON-PRINT (SET status) Other bits will be selected to “RESET” status.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-22 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 1 NON-PRINT OPTION I BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-23 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 2 NON-PRINT OPTION II BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-24 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 6 3 OPTIONAL FUNCTION I BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-25 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 23 4 OPTIONAL FUNCTION II BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-26 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 6 REMOTE SLIP PRINTER CONTROL BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-27 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 7 OPTIONAL FUNCTION III BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-28 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 568 11 NON-PRINT OPTION III BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-29 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 4 17 OPTIONAL FUNCTION IV BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-30 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 19 CONSIGNMENT OPTION BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-31 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 20 TAX CONTROL I BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-32 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 21 TAX CONTROL II BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-33 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 22 TAX CONTROL III BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-34 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 1 27 DRAWER OPTION BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-35 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 28 OPTIONAL FUNCTION VI BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-36 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 6 29 OPTIONAL FUNCTION VII BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-37 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 30 OPTIONAL FUNCTION VIII BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-38 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 31 OPTIONAL FUNCTION IX BIT NO. ITEM SELECTIVE STATUS STANDA RD STAT US REMARKS RESET * 1 -- vacant -- SET RESET * 2 -- vacant -- SET RESET NON-PRINT * 3 Date, day of week, and Register No.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-39 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 32 OPTIONAL FUNCTION X BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-40 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 2 33 OPTIONAL FUNCTION XI BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-41 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 12 34 OPTIONAL FUNCTION XII BIT NO. ITEM SELECTIVE STATUS STANDA RD STAT US REMARKS RESET . (POINT) -- ex) 1.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-42 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 36 FOREIGN CURRENCY OPTION BIT NO. ITEM SELECTIVE STATUS STANDA RD STAT US REMARKS RESET 0.00 ($, €, £, etc.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-43 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 37 OPTIONAL FUNCTION XIII BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-44 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 38 OPTIONAL FUNCTION XIV BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-45 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 39 OPTIONAL FUNCTION XV BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-46 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 42 OPTIONAL FUNCTION XVI BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-47 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 47 PC OPTION BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.5 System Option Programming 6-48 System Option Table Standard Bit Set (auto-set by RAM Clear) ADDRESS NO. CONTENTS 0 49 OPTIONAL FUNCTION XVII BIT NO.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.6 Commercial Message Programming 6-49 6.6 Commercial Message Programming A maximum of 96 characters of Commercial Message (32 characters x 3 lines) to be printed on the receipt is programmed here. Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu Depress [1] or [Enter] .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.6 Commercial Message Programming 6-50 3) Example: To program the following Commercial Message. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [1] or [Enter] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.6 Commercial Message Programming 6-51 (continued from the previous page) Operation LCD Display Remarks The [Enter] key depression results in that the input message is entered and displayed. When the [Enter] key is depressed, the message programmed in the 2nd line is printed.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.7 Footer Message Programming 6-52 6.7 Footer Message Programming A maximum of 64 characters of Footer Message (32 c haracters x 2 lines) to be printed on the receipt is programmed here. Prior to the Footer Message Programming, be sure to select RESET status for Address No.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.7 Footer Message Programming 6-53 3) Example: To program the following Footer Message. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [1] or [Enter] key. Depress the [ ↓ ] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.7 Footer Message Programming 6-54 (continued from the previous page) Operation LCD Display Remarks The [Enter] key depression allows the ECR to enter the 2nd line message input mode. (The [C] key depression clears the message already programmed.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.8 Store Name Message Programming 6-55 6.8 Store Name Message Programming A maximum of 128 characters of Store Name Message (32 characters x 4 lines) to be printed on the receipt is programmed here. Prior to the Store Name Message Programming, be sure to select SET status for Address No.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.8 Store Name Message Programming 6-56 NOTES: 1. For each line, a maximum of 32 one-byte chara cte rs or 16 two-byte characters can be entered. A combination of both types is also available. 2. When blanks are entered for the whole one line, it results in one line feed.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.8 Store Name Message Programming 6-57 3) Example: To program the following Store Message. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [1] or [Enter] key. Depress the [ ↓ ] key twice.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.8 Store Name Message Programming 6-58 (continued from the previous page) Operation LCD Display Remarks The [Enter] key depression results in that the input message is entered and displayed. When the [Enter] key is depressed, the message programmed in the 2nd line is printed.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.9 Department Name Programming 6-59 6.9 Department Name Programming A maximum of 16 characters of department name is programmed here. Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.9 Department Name Programming 6-60 3) Example To program “FOOD” as the name of Department 01. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key. The cursor is moved on to “ 2 NAMES ”.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.10 Department Group Name Programming 6-61 6.10 Department Group Name Programming In this operation, the name of each Department Group is programmed. Which Departments are linked to each Group has been set in the DEPARTMEN T TABLE PROGRAMMING operation.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.10 Department Group Name Programming 6-62 (continued from the previous page) Operation LCD Display Remarks Depress the [2] or [Enter] key. “ 2 NA MES ” is selected. Depress the [ ↓ ] key. The cursor is moved on to “ 2 DP GROUP NAME ”.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.11 Cashier Name and Status Programming 6-63 6.11 Cashier Name and Status Programming Cashier Name and Cashier Status for each cashier can be programmed here. Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.11 Cashier Name and Status Programming 6-64 NOTES: 1. Cashiers 1 to 8 are programmed with t he names “1CL” to “8CL” as default setting. 2. For the name of each cashier, a maximum of 12 one-byte or 6 two-byte characters can be entered.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.11 Cashier Name and Status Programming 6-65 (continued from the previous page) Operation LCD Display Remarks The [Enter] key depression allows the ECR to enter the cashier 1 name input mode. (The [C] key depression clears the name already programmed.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.12 PLU Name Programming 6-66 6.12 PLU Name Programming A maximum of 16 characters of PLU name is programmed here. Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.12 PLU Name Programming 6-67 (continued from the previous page) Operation LCD Display Remarks Depress the [2] or [Enter] key. Depress the [ ↓ ] key three times. The cursor is moved on to “ 4 PLU (ITM NO.) NAME ”.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.13 Salesperson Name Programming 6-68 6.13 Salesperson Name Programming By programming Salesperson here, the name of each salesperson can be programmed in a maximum of 12 characters.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.13 Salesperson Name Programming 6-69 3) Example To program “White” on Salesperson Code 01: Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key. The cursor is moved on to “ 2 NAMES ”.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.13 Salesperson Name Programming 6-70 (continued from the previous page) Operation LCD Display Remarks The [End] key depression allows the ECR to end this programming. A long receipt is issued and the display returns to Main Menu screen.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.14 Financial Report Item Name Programming 6-71 6.14 Financial Report Item Name Programming Item Names printed on Financial Report are programmed here. Many of them are also printed on sales receipts. Other Line Item Names will be programmed in 6.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.14 Financial Report Item Name Programming 6-72 3) Example To program “ NET GT ” instead of “NET GT” for Item Code 2 (NET GT) all in double-sized characters. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.14 Financial Report Item Name Programming 6-73 (continued from the previous page) Operation LCD Display Remarks The [End] key depression allows the ECR to end this programming. A long receipt is issued and the display returns to Main Menu screen.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.14 Financial Report Item Name Programming 6-74 Financial Report Item Name Table ( continued ) Item Code Item Name Standard Program 26 Media 4 Sales (CPN) C P N.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.14 Financial Report Item Name Programming 6-75 Financial Report Item Name Table (c ontinued ) Item Code Item Name Standard Program 71 Media 2-in-drawer Differe.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.14 Financial Report Item Name Programming 6-76 Financial Report Item Name Table (c ontinued ) Item Code Item Name Standard Program 116 VAT 2 or Tax 2 Exempt V .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming 6-77 6.15 Print Line Item Name Programming Print Line Item Names not listed in Section 6.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming 6-78 3) Example To program the amount mark “€ ” in Item Code 7: (T he amount mark has not been preset a s the standard program data). Meanwhile, the names of the other items in t he Item Code 7 should remain unchanged as the standard program data (i.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming 6-79 (continued from the previous page) Operation LCD Display Remarks The [End] key depression allows the ECR to end this programming. A long receipt is issued and the display returns to Main Menu screen.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming 6-80 Print Line Item Name Table (continued) Max. Number of Characters Item Code Item Name or Application Standard Program V.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming 6-81 Print Line Item Name Table (c ontinued ) Max. Number of Characters Item Code Item Name or Application Standard Program.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.15 Print Line Item Name Programming 6-82 NOTES: 1. The standard program data for the Am ount Mark in Item Code 7 is set with a blank after a RAM Clear.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.16 Display item Name Programming 6-83 6.16 Display Item Name Programming Display Item Name to be displayed on the LCD disp lay can be programmed here. (Max. 16 characters) Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.16 Display item Name Programming 6-84 Display Item Name Table Item Code Application Standard Program 1 -- vacant -- 2 Signed-OFF condition (in REG, MGR, or - m.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.16 Display item Name Programming 6-85 3) Example To program “BALANCE DUE” instead of standard program data “TOTAL” for Item Code 3. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.16 Display item Name Programming 6-86 (continued from the previous page) Operation LCD Display Remarks The [End] key depression allows the ECR to end this programming. A long receipt is issued and the display returns to Main Menu screen.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming 6-87 6.17 Error Item Name Programming Error item names to be displayed on the LCD displa y are programmed here.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming 6-88 3) Example To program “CALL MANAGER” instea d of standard prog ram data “MANAGER REQUIRE D” for Error Code 3. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming 6-89 (continued from the previous page) Operation LCD Display Remarks The [End] key depression allows the ECR to end this programming. A long receipt is issued and the display returns to Main Menu screen.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming 6-90 Error Code and Error Item Name Table ( continued ) Error Code Content or Cause of Error Standard Program 31 D R A W E R L I.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming 6-91 Error Code and Error Item Name Table ( continued ) Error Code Content or Cause of Error Standard Program 8 1 S L I P PAPE R.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.17 Error Item Name Programming 6-92 Error Code and Error Item Name Table ( continued ) Error Code Content or Cause of Error Standard Program 133 134 -- vacant .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming 6-93 6.18 Read/Reset Report Name Programming Read/Reset Report Names are programmed here.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming 6-94 3) Example To program “X_DP_PROFIT” instead of standard program data “X_PROFIT” for Report No. 21. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming 6-95 (continued from the previous page) Operation LCD Display Remarks The [End] key depression allows the ECR to end this programming. A long receipt is issued and the display returns to Main Menu screen.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming 6-96 Read/Reset Report Name Table ( continued ) X: Daily Read Z: Daily Reset GTX: GT Read GTZ: GT Reset Report No.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.18 Read/Reset Report Name Programming 6-97 Read/Reset Report Name Table ( continued ) X: Daily Read Z: Daily Reset GTX: GT Read GTZ: GT Reset Report No.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming 6-98 6.19 Department Table Programming For each department, memory opening, and department va rious statuses settings are performed here.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming 6-99 *1: Department Group No. • Input a department group code (2 digits: 01 to 15), then depress the [Enter] key. • To cancel a department group, input 0 then depress the [Enter] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming 6-100 *5: High Amount Limit • Enter a maximum of 7 digits to be set as the high amount to be locked out. Example) To prohibit any amount equal to or larger than 40,00: 4000 [Enter] (Allows any amount equal to or smaller than 39,99.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming 6-101 (continued from the previous page) Operation LCD Display Remarks Depress the [3] or [Enter] key. “ 3 DP/PLU ” is selected. Depress the [1] or [Enter] key. “ 1 DP ” is selected.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming 6-102 (continued from the previous page) Operation LCD Display Remarks Move the cursor on to a desired status setting with the [ ↓ ] or [ ↑ ] key. The [?] key depression results in that the following guidance message appears on the LCD display.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.19 Department Table Programming 6-103 (continued from the previous page) Operation LCD Display Remarks Depress the [Rtn] key. The display returns to the Department Setting screen. Move the cursor on to another desired department with the [ ↓ ] or [ ↑ ] key, then depress the [Enter] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.20 Department Preset Price Setting or Changing 6-104 6.20 Department Preset Price Setting or Changing The preset price of each department may be set in the DEPARTMENT TABL E PROGRAMMING already described.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.20 Department Preset Price Setting or Changing 6-105 (continued from the previous page) Operation LCD Display Remarks Depress the [3] or [Enter] key. “ 3 DP/PLU ” is selected. Depress the [1] or [Enter] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.21 Department Listing Capacity (LC) Programming 6-106 6.21 Department Listing Capacity (LC) Programming The High Amount to be Locked Out (HALO) and Low Amount to be Locked Out (LALO) relating to the department entry are programmed here.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.21 Department Listing Capacity (LC) Programming 6-107 • The HALO and LALO pro grammed here are effective at the department entry in REG m ode only. They are not effective in MGR and - mode, as a maximum of 7-digit amount value can be entered.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.21 Department Listing Capacity (LC) Programming 6-108 (continued from the previous page) Operation LCD Display Remarks Input 10 , then depress the [Enter] key. (LALO: 10) When the [Enter] key is depressed, the programmed data is printed.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.22 Key Sticker Printing 6-109 6.22 Key Sticker Printing Key stickers of department names which were progr ammed in the DEPARTMENT NAME PROGRAMMING can be printed on the receipt printer.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.22 Key Sticker Printing 6-110 NOTES: 1. Print format < Single key > • For the single key, a maximum of 12-digit departm ent name (6 characters x 2 lines) can be printed.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.22 Key Sticker Printing 6-111 (continued from the previous page) Operation LCD Display Remarks Depress the [1] or [Enter] key. ” 1 A LL DP ” is selected. A confirmation message is displayed. The [End] key depression allows the ECR to end this operation.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.22 Key Sticker Printing 6-112 (2) To print part of department names. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key twice. The cursor is moved on to “ 3 DP/PLU ”.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 6-113 6.23 PLU Table Programming This programming can be operated when new PLU items are to be added, PLU program data is to be changed, or PLUs are to be deleted.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 6-114 NOTES: 1. A maximum of 1,000 PLUs are programm able. 2 If a PLU is linked to a negative department, the PLU is automatically set as negative PLU. 3. The [PLU] key here indicates the key labelled si mply as “PLU” but not any PLU preset-code keys.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 6-115 3) Example To program the following PLU data: PLU Code: 0010 Linked Department: Department 1 Preset Price: €1,00 2nd Preset Pr.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 6-116 (continued from the previous page) Operation LCD Display Remarks Input 100 , then depress the [Enter] key. (Preset Price €1,00 is set.) The [?] key depression results in that the following guidance message appears on the LCD display.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 6-117 6.23.2 Deletion To delete a PLU with sales data of zero: Any time outside a sale To delete a PLU with sales data of not zero: After PLU Reset Mode Lock: SET Individual PLU Deletion : The programmed PLU data is deleted individually.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 6-118 (continued from the previous page) Operation LCD Display Remarks Depress the [ ↓ ] key. Depress the [1] or [Enter] key. “ 2 PLU ” is selected. Depress the [ ↓ ] key three times.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.23 PLU Table Programming 6-119 All PLU Deletion: The programmed PLU data is deleted entirely. 1) Menu Tree 2) Operation Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key twice.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.24 PLU Preset Price Setting or Changing 6-120 6.24 PLU Preset Price Setting or Changing The preset price of each PLU may be set in the PLU TABLE PROGRAMMING already described. However, in setting or changing the price only (not other programmed data), the following operation will be more convenient.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.24 PLU Preset Price Setting or Changing 6-121 NOTES: 1. When no price is input then the [Enter] key is depressed, the PLU will be open (i.e. open-price PLU). 2. If inputting a nonexistent PLU code that was not pr ogrammed in the PLU Table Programm ing, this may cause an error.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.24 PLU Preset Price Setting or Changing 6-122 (continued from the previous page) Operation LCD Display Remarks Make sure the cursor is shown on 01PRICE. Then, input 315 and depress the [Enter] key. The 1st preset price is changed from €1,05 to €3,15.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.25 PLU Preset-Code Key Setting 6-123 6.25 PLU Preset-Code Key Setting When there are any keys programmed as PLU Preset-c ode Keys (SFKC 96) on the ECR Keyboard.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.25 PLU Preset-Code Key Setting 6-124 • For PK-2 Keyboard Main Menu ECR is being outside a sale and in SET mode. Depress [ ↓ ] twice then [Enter] . or Depress [3] . “ 3 DP/PLU ” is selected. Depress [ ↓ ] then [Enter] .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.25 PLU Preset-Code Key Setting 6-125 • Flat type keyboard 1 8 15 22 29 36 43 50 57 64 71 77 83 90 97 100 2 9 16 23 30 37 44 51 58 65 72 78 84 91 98 101 3 10 .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.25 PLU Preset-Code Key Setting 6-126 (continued from the previous page) Operation LCD Display Remarks Depress the [ ↓ ] key. The cursor is moved on to “ 2 PLU CODE KEY ”. Depress the [2] or [Enter] key. “ 2 PLU CODE KEY ” is selected.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.25 PLU Preset-Code Key Setting 6-127 (continued from the previous page) Operation LCD Display Remarks Depress the [ ↓ ] key. The cursor is moved on to “ 2 PLU ”. Depress the [2] or [Enter] key. “ 2 PLU ” is selected.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.26 %+ and %- Preset Rate Setting 6-128 6.26 % + and % - Preset Rate Setting A preset rate may be set on each of the [%+] and [% -] keys, one independent rate for each key. Once a rate is preset, the % key will simply be depressed without a prior ra te entry to activate the pr eset rate.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.26 %+ and %- Preset Rate Setting 6-129 3) Example To program the following rate on the [%-] key: [%-] key ………. Rate 5,00% Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key three times.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.27 VAT or Add-on Tax Rate Setting 6-130 6.27 VAT or Add-on Tax Rate Setting The rates of VATs or Add-on Taxes are set in thi s operation,. (Which VAT or Add-on Tax is applicable to each Department or PLU has already been set in the DEPARTMENT T ABLE PROGRAMMING and PLU TABLE PROGRAMMING.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.27 VAT or Add-on Tax Rate Setting 6-131 3) Example To set the following VAT rate: VAT1………10% Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key three times.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.28 Foreign Currency Exchange Rate Setting 6-132 6.28 Foreign Currency Exchange Rate Setting The rate of each foreign currency (corresponding to the [CUR1] to [CUR5] keys ) are set in this operation.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.28 Foreign Currency Exchange Rate Setting 6-133 Foreign Currency Exchange Rate Calculation 1. The rate must be calculated in the su bsidiary cu rrency unit values for both the domestic and the foreign currencies.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.28 Foreign Currency Exchange Rate Setting 6-134 (continued from the previous page) Operation LCD Display Remarks Make sure the cursor is shown on 01CUR1. Then, input 1.20 and depress the [Enter] key. The exchange rate from € to $ is set on the [CUR1] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.29 Negative Amount Key Limit Amount Setting 6-135 6.29 Negative Amount Key Limit Amount Setting The limit amount to be entered thro ugh each of the negat ive-amount keys [VND CPN] , [STR CPN] , and [-] Are set here.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.29 Negative Amount Key Limit Amount Setting 6-136 3) Example To set the following preset amount on the keys below: Key Limit Amount [VND CPN] 10.00 [STR CPN] 20.00 Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key three times.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.30 Time Setting or Adjustment 6-137 6.30 Time Setting or Adjustment Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode. Depress [ ↓ ] four times then [Enter] .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.31 Date Setting or Adjustment 6-138 (continued from the previous page) Operation LCD Display Remarks Input 1315 . The time “13:15” is set. The [End] key depression allows the ECR to end this setting. A long receipt is issued and the display returns to Main Menu screen.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.31 Date Setting or Adjustment 6-139 3) Example To set Date “Monday 31 October, 2005” Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key four times. The cursor is moved on to “ 5 BASIC ”.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.32 Store/Register No. Setting 6-140 6.32 Store/Register No. Setting A maximum of 6 digits may be set as ID No.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.32 Store/Register No. Setting 6-141 (continued from the previous page) Operation LCD Display Remarks Depress the [ ↓ ] key twice. The cursor is moved on to “ 3 REGISTER NO. ”. Depress the [3] or [Enter] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.33 Hourly Range Table Setting 6-142 6.33 Hourly Range Table Setting By setting a maximum of 24 terms per day, sale s data control for each term can be performed. After Hourly Range Reset Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.33 Hourly Range Table Setting 6-143 3) Example To set the following hourly range table: TIME01 until 8:00* TIME02 8:00 to 12:00 TIME03 12:00 to 15:00 TIME04 15:00 to 19:00 *(The first term is automatically c ontinued from 19:00 of the preceding day.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.33 Hourly Range Table Setting 6-144 (continued from the previous page) Operation LCD Display Remarks Input 1500 , then depress the [Enter] key. (TIME03 is set with 15:00.) Input 1900 , then depress the [Enter] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.33 Hourly Range Table Setting 6-145 (continued from the previous page) Operation LCD Display Remarks Depress the [2] or [Enter] key. “ 2 RESET ” is selected. A guidance message is displayed. The [End] key depression allows the ECR to end this setting.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.34 Tone Volume Setting 6-146 6.34 Tone Volume Setting Key-in tone for the ECR keyboard and error t one are selectable from High, Low, and OFF. Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.34 Tone Volume Setting 6-147 3) Example To change the key tone from “HIG H” (default setting) to “LOW”. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key four times.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.35 Report Item Print/Non-Print Setting 6-148 6.35 Report Item Print/Non-Print Setting Items to be printed on Financial, Cashier, and Salesperson Reports are set here. Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.35 Report Item Print/Non-Print Setting 6-149 3) Example To set Item Code 3 “NEG GT” with Non-print status. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key five times.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.35 Report Item Print/Non-Print Setting 6-150 Report Item Name Table Item Code Item Name Standard Program 1 Ground Total G T 2 NET GT N E T G T 3 NEG GT N E G G.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.35 Report Item Print/Non-Print Setting 6-151 Report Item Name Table ( Continued ) Item Code Item Name Standard Program 46 Media 2-in-drawer (CRT) C R T I D 47 .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.35 Report Item Print/Non-Print Setting 6-152 Report Item Name Table ( Continued ) Item Code Item Name Standard Program 91 Transfer + Daily T R F + 92 Transfer .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.36 Key Status Programming 6-153 6.36 Key Status Programming Various selective statuses of media keys and other function keys are programmed here. Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.36 Key Status Programming 6-154 (continued from the previous page) Operation LCD Display Remarks Depress the [ ↓ ] key twice. The cursor is moved on to “ 3 KEY FUNCTION ”. Depress the [3] or [Enter] key. “ 3 KEY FUNCTION ” is selected.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.36 Key Status Programming 6-155 Key Status Table (Key Code 1 to 20) Bit No. Function SET RESET 1 TOTAL-only TOTAL-only key 2 TENDER-only TENDER-only key If bot.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.36 Key Status Programming 6-156 Key Status Table (Key Code 21 to 42) Bit No. Function SET RESET 1 -- vacant bit -- 2 MGR INTERVENTION (in REG mode) Compulsory .
6. TERMINAL FILE PROGRAMMING EO3-11106 6.37 Cash Tender key Preset Amount Setting 6-157 6.37 Cash Tender Key Preset Amount Setting A maximum of 6-digit amount is preset to the Cash Key ( [CASH 1] to [CASH 3] ).
6. TERMINAL FILE PROGRAMMING EO3-11106 6.37 Cash Tender key Preset Amount Setting 6-158 3) Example To preset €10000,00 to the [CASH 1] key and €10,00 to the [CASH 2] key. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key five times.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.38 Drawer Warming Time Setting 6-159 6.38 Drawer Warning Time Setting This operation set s the number of seconds as the period of time for the cash drawer remaining open until the alarm buzzer is generated to warn operator to close the drawer.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.38 Drawer Warming Time Setting 6-160 3) Example To set 30 seconds for the drawer warning time. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key five times.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.39 Special Rounding Process Setting, 1-digit type 6-161 6.39 Special Rounding Process Setting, 1-digit type For Special Rounding and De nmark/Australia rounding, the pre-rounded value of the least effective digit and the post-rounded value are set here.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.39 Special Rounding Process Setting, 1-digit type 6-162 Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key five times. The cursor is moved on to “ 6 OTHER ”.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.40 Special Rounding Process Setting, 2-digit type 6-163 6.40 Special Rounding Process Setting, 2-digit type For Special Rounding and Denmark ro unding, the pre-rounded value of the two least effective digit and the post- rounded value are set he re.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.40 Special Rounding Process Setting, 2-digit type 6-164 Example of Denmark rounding For the Denmark rounding, the amount total is rounded as shown below.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.40 Special Rounding Process Setting, 2-digit type 6-165 (continued from the previous page) Operation LCD Display Remarks Input 3725 , then depress the [Enter] key. Input 6250 , then depress the [Enter] key. Input 8775 , then depress the [Enter] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.41 Number of Receipt Print Buffer Line Setting 6-166 6.41 Number of Receipt Print Buffer Line Setting The number of receipt print buffer line is set here. When it reaches the set value, only a receipt print operation starts.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.41 Number of Receipt Print Buffer Line Setting 6-167 (continued from the previous page) Operation LCD Display Remarks Depress the [ ↓ ] key seven times. The cursor is moved on to “ 8 RCT PRINT BUFFER ”. Depress the [8] or [Enter] key.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.42 Serial No. Setting 6-168 6.42 Serial No. Setting A maximum of 8-digit serial No. is set here. The se rial No. will be printed on the Daily and GT Financial Read/Reset Reports. Any time outside a sale Mode Lock: SET 1) Menu Tree 2) Operation Flowchart Main Menu ECR is being outside a sale and in SET mode.
6. TERMINAL FILE PROGRAMMING EO3-11106 6.42 Serial No. Setting 6-169 3) Example To set the serial No. 12345678. Operation LCD Display Remarks When the ECR is being outside a sale and in SET mode, depress the [ ↓ ] key five times. The cursor is moved on to “ 6 OTHER ”.
7. VERIFICATION OF PROGRAMMED DATA EO3-11106 7. VERIFICATION OF PROGRAMMED DATA 7- 1 7. VERIFICATION OF PROGRAMMED DATA The programmed data entered in the preceding chapt er can be read for verification purposes.
7. VERIFICATION OF PROGRAMMED DATA EO3-11106 7. VERIFICATION OF PROGRAMMED DATA 7- 2 PROGRAM DATA READ menu 1 MESSA GES 1 COMMERCIAL MESSA GE 2 FOO TER MESSAGE 3 ST ORE MESSAGE 2 MAMES 1 DP GROUP NAME.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Toshiba MA-600 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Toshiba MA-600 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Toshiba MA-600 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Toshiba MA-600 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Toshiba MA-600, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Toshiba MA-600.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Toshiba MA-600. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Toshiba MA-600 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
