Manuale d’uso / di manutenzione del prodotto 222D del fabbricante AEG
Vai alla pagina of 20
222 D Fume Extractor Hood Installation and Operating Instructions.
2 Printed on recycled paper. AEG putting words into action..
3 Contents Introduction 4 Extraction mode 4 Recirculation mode 5 Electrical connections 6 Technical details 7 Installation 8 Safety warnings for kitchen unit installer 8 Wall unit mounting 10 Wall mou.
4 2 Introduction Extraction mode ● The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (available as an accessory). ● The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear.
5 ● Move the lever L to position A Fig. 3 . ● When connecting up the hood using a telescopic wall pipe, you should use an uninflammable outlet hose ABS 120 (120 mm Ø) available as an accessory. Recirculation mode ● The air is filtered and recirculated through the front grid.
6 Electrical connection 220-240 V - using fixed power supply line with plug. (The unit should only be connected up by an authorized electrician). Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp.
7 Technical details Dimensions Height x Width x Depth (in cm) 13 x 59,9 x 51 Weight N e t : 6,9 kg Gross: 7, 8 k g Maximum absorbed power: 205 W Motor absorption 1 x 125 W Lighting: 2 x 4 0 W Length o.
8 Installation Safety warnings for kitchen unit installer ● When used as an extractor unit, the hood must be fitted with a 120mm diameter hose. ● If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.
9 ● The national decree on fuel-burning systems specifies a maximum depression of 0.04 bar in such rooms. ● Hoods can only be used safely with appliances connected to a chimney if the room and/or .
10 Wall unit mounting ● Make the holes on the bottom of the cupboard, using the drilling template . ● From inside the cupboard, insert the 4 supplied screws and tighten them in the appropriate holes on the appliance.
11 Wall mounting ● Fix the drilling template to the wall. ● Make 3 Ø 8mm holes in the wall 2 at points I , 1 as desired at points L . ● Insert the three Ø 8mm expansion plugs into the wall. ● Insert 2 5x45 screws at points I but do not tighten them completely.
12 Hood Operation ● The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated.
13 ● Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil in particular should never be left uncovered. ● Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into flames.
14 6 Maintenance and care ● The hood must always be disconnected from the mains power supply before beginning any maintenance work. Opening the grid ● Open the latch L and swing the grille downwards. Fig. 6. ● To remove the grid, pull it forwards from the right and release it.
15 8 Removing the filter Open the grid and remove the stops M to take out the filter. See Fig. 7. Carbon filter ● The activated carbon filter should only be used if you want to use the hood in its filtering function. ● To do this you will need an original AEG activated carbon filter (see special accessories).
16 Warning ● Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. Changing the light bulb ● Disconnect the unit from the mains power supply.
17 What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that the fan speed control is set to 1, 2 or 3.
18 Service and spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning 08705 929 929 Y our call will be automatically routed to the Service Centre covering your post code area.
19.
LI02GB Ed. 05/02 AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http:/ /www .aeg.hausgeraete.de © Copyright by AEG.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il AEG 222D è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del AEG 222D - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso AEG 222D imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul AEG 222D ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il AEG 222D, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del AEG 222D.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il AEG 222D. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo AEG 222D insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
