Manuale d’uso / di manutenzione del prodotto 2009 Escalade EXT del fabbricante Cadillac
Vai alla pagina of 546
Seats and Restraint System ............................. 1 - 1 Head Restraints ......................................... 1 - 2 Front Seats ............................................... 1 - 3 Rear Seats .............................................. 1-10 Safety Belts .
Tires ...................................................... 6-54 Appearance Care ..................................... 6-94 Vehicle Identification ............................... 6-102 Electrical System .................................... 6-103 Capacities and Specifications .
GENERAL MOTORS, GM, the GM Emblem, CADILLAC, the CADILLAC Crest & Wreath, and the names ESCALADE and EXT are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. GM reserves the right to make changes after that time without notice.
Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning.
Vehicle Symbols The vehicle has components and labels that use symbols instead of text. Symbols are shown along with the text describing the operation or information relating to a specific component, control, message, gage, or indicator. M : This symbol is shown when you need to see your owner manual for additional instructions or information.
g : Outside Power Foldaway Mirrors } : Power / : Remote Vehicle Start > : Safety Belt Reminders 7 : Tire Pressure Monitor _ : Tow/Haul Mode F : Traction Control M : Windshield Washer Fluid vi.
Head Restraints .............................................. .1-2 Front Seats ..................................................... .1-3 Power Seats ................................................. .1-3 P o w e r L u m b a r .......................
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. { CAUTION: With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash.
Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
• Raise or lower the rear part of the seat cushion by moving the rear of the control up or down. • Raise or lower the entire seat by moving the entire control up or down. The power reclining seatback control is located behind the power seat control on the outboard side of the seats.
Release the control when the lower seatback reaches the desired level of lumbar support. Your vehicle may have a memory function which allows seat settings to be saved and recalled.
Heated and Cooled Seats If the front seats have the heated and cooled seat feature, the buttons used to control this feature are located on the climate control panel. { (Cooled Seat): To cool the entire seat, press the button with the cooled seat symbol.
Memory Features Your vehicle has the memory package. The controls for this feature are located on the driver’s door, and are used to program and recall memory settings for the driver’s seat, outside mirrors, steering wheel position, and the adjustable throttle and brake pedal feature, if your vehicle has it.
Easy Exit Seat The control for this feature is located on the driver’s door between buttons 1 and 2. With the vehicle in P (Park), the exit position can be recalled by pressing the exit button. You will hear a single beep. The driver’s seat will move back.
{ CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Rear Seats Rear Seat Operation The rear seat is a 60/40 split bench seat that can be folded to give you more cargo space and access to the folding midgate. See Midgate ® on page 2-11 for more information on operation of the folding midgate. To fold either side of the seat do the following: 1.
{ CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. { CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-14.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 1-15.
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces.
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Q: What is wrong with this? A: The belt is behind the body. { CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Q: What is wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index.
5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling off the shoulder.
Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed on a shoulder belt, the comfort guide positions the belt away from the neck and head.
3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. { CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide. Slide the guide into its storage clip on the interior body or storage pocket on the side of the seat. Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women.
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. The manufacturer’s instructions that come with the booster seat state the weight and height limitations for that booster.
Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs.
{ CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
{ CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Never leave children unattended in a vehicle and never allow children to play with the safety belts.
{ CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards.
Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (B) provides restraint for the child’s body with the harness.
Securing an Add-On Child Restraint in the Vehicle { CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
Where to Put the Restraint According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position.
Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in the vehicle — even when no child is in it. Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash.
Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
The right side rear passenger and center seating positions have exposed metal anchors located in the crease between the seatback and the seat cushion. To assist you in locating the top tether anchors, the top tether anchor symbol is located near the top tether anchors.
According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. See Where to Put the Restraint on page 1-40 for additional information.
Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not fold the empty rear seat with a safety belt buckled.
If the position you are using has an adjustable headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint.
3. Tighten the top tether. 4. Push and pull the child restraint in dif ferent directions to be sure it is secure. Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle.
3. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint.
safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH) on page 1-41 for top tether anchor locations. Do not secure a child seat in a position without a top tether anc.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
If a child restraint has been installed and the on indicator is lit, see “If the On Indicator is Lit for a Child Restraint ” under Passenger Sensing System on page 1-61 for more information. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.
Here are the most important things to know about the airbag system: { CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
{ CAUTION: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Where Are the Airbags? The driver’s frontal airbag is in the middle of the steering wheel. The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side.
The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows. { CAUTION: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death.
When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inflate if the impact exceeds a predetermined deployment threshold.
Roof-rail airbags are not intended to inflate in rear impacts. Both roof-rail airbags will deploy when either side of the vehicle is struck, or if the sensing system predicts that the vehicle is about to roll over, or in a severe frontal impact.
What Will You See After an Airbag Inflates? After the frontal airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy.
In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system.
The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbag and the roof-rail airbags (if equipped) are not affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat and safety belt.
The passenger sensing system is designed to turn off the right front passenger frontal airbag if: • The right front passenger seat is unoccupied. • The system determines an infant is present in a child restraint. • A right front passenger takes his/her weight off of the seat for a period of time.
If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle of f. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
If the Of f Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat.
Additional Factors Af fecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status.
Servicing Your Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Your dealer/retailer and the service manual have information about servicing the vehicle and the airbag system.
installed under or on top of the seat fabric, could also interfere with the operation of the passenger sensing system. This could either prevent proper deployment of the passenger airbag(s) or prevent the passenger sensing system from properly turning off the passenger airbag(s).
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Replacing Restraint System Parts After a Crash { CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash.
Keys .............................................................. .2-3 Remote Keyless Entry (RKE) System ............... .2-4 Remote Keyless Entry (RKE) System Operation .................................................. .2-4 Remote Vehicle Start ..
OnStar ® System ............................................ .2-56 Universal Home Remote System ..................... .2-59 Universal Home Remote System Operation (With Three Round LED) ........................... .2-60 Storage Areas ................
Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed.
Remote Keyless Entry (RKE) System The Remote Keyless Entry (RKE) system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
/ (Remote Vehicle Start): Press to start the engine from outside the vehicle using the RKE transmitter. See Remote Vehicle Start on page 2-7 for additional information.
The vehicle comes with two transmitters. Each transmitter will have a number on top of it, “1” or “2”. These numbers correspond to the driver of the vehicle. For example, the memory seat position for driver 1 will be recalled when using the transmitter labeled “1”, if enabled through the DIC.
To replace the battery: 1. Separate the transmitter with a flat, thin object inserted into the notch, located above the metal base. 2. Remove the old battery. Do not use a metal object. 3. Insert the new battery, positive side facing up. Replace with a CR2032 or equivalent battery.
When the vehicle starts, the parking lamps will turn on and remain on while the vehicle is running. If the vehicle is left running it will automatically shut off after 10 minutes unless a time extension has been done.
Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
You can turn the delayed locking feature off or back on again by doing the following: 1. Press and hold the power door lock switch in the lock position. 2. Press unlock twice on the RKE transmitter. This feature will not operate if the key is in the ignition.
When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door by lifting the rear door manual lock, using the power door lock switch, or the Remote Keyless Entry (RKE) transmitter, if the vehicle has one. 2. Open the door from the outside.
Midgate ® Operation Your vehicle is equipped with a Midgate ® and a removable rear glass panel. The Midgate ® allows you to extend the length of your vehicle’s cargo area. The following are the main components of the Midgate ® system: A. Latch Levers B.
Rear Glass Removal and Storage { CAUTION: If the removable rear glass is not stored properly, it could be thrown about the vehicle in a crash or sudden maneuver. People in the vehicle could be injured. Whenever you store the rear glass in the vehicle, always be sure that it is stored securely in the Midgate ® storage pocket.
3. While holding the rear glass in place, press the glass-catch release button (C) and pull the top of the rear glass toward you using the grab handle(s) (B) located at the top of the rear glass. 4. With the rear glass tilted toward you, lift it out from the lower window frame channel.
5. Load the rear glass into the storage pocket in the Midgate ® , guiding the lower edge of the rear glass behind the three rear glass retaining tabs (E). Hold the rear glass flat against the storage pocket, with grab handles facing you, until the next step.
Once both glass lock knobs are in the locked position, the rear glass is securely stored. 7. Push both latch levers up to the locked position. You should hear a click when each latch lever locks correctly. The rear seats can be returned to the normal position when the rear glass is out and stored properly in the storage pocket.
4. With the rear glass tilted at an angle, place the bottom edge in the lower channel of the window frame. Be sure to align the rear glass side-to-side using the alignment arrows (G). 5. Apply a firm downward pressure and then push the rear glass flat against the window frame.
6. Push the rear glass flat against the window frame and push each latch lever up until it locks. You should hear a click when each latch lever locks correctly. Lowering the Midgate ® with the Rear Glass in Place The Midgate ® can be lowered to allow the cargo area of your vehicle to extend into the cab.
2. Standing outside of the vehicle, hold the Midgate ® securely so it does not fall forward. Turn the Midgate ® handle clockwise and pull the Midgate ® toward you.
Lowering the Midgate ® with the Rear Glass in the Storage Pocket This procedure works the same as the procedure described previously, but when you lower the Midgate ® with the rear glass in the stored position, you will notice that the entire crossbar will lower with the Midgate ® .
Raising the Midgate ® To return the Midgate ® to its normal position, raise the Midgate ® up with a firm swinging motion until it latches into place securely. This will help to ensure that the Midgate ® closes with enough force to engage the latches.
Tailgate Removal The tailgate is not to be removed. This may cause damage to electrical connector resulting in loss of lock/unlock and rear vision camera function. Power Assist Steps Your vehicle may have power assist steps. The power assist steps automatically extend from beneath the vehicle on the side in which the door has been opened.
Windows { CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows { CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed.
Express-Down/Up Windows Windows with the express feature allow the windows to be raised and lowered all the way without holding the switch. Press or pull the switch fully and release it to activate the express feature. The express mode can be canceled at any time by briefly pressing or pulling the switch.
Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or is not working, you will need to reprogram each front power window for the express-up feature to work. Before reprogramming, replace or recharge the vehicle’s battery.
Sun Visors with Fixed Rod and Pull-out Extension Your vehicle may have this feature. Pull the sun visor down to block glare. Pull the sun visor extender out for additional coverage. Detach the sun visor from the center mount and swing it to the side to cover the side window.
3. Close all doors. The security light should go off after about 30 seconds. The alarm is not armed until the security light goes off. The content theft deterrent system does not sense if the midgate or tailgate are open or ajar, therefore, vehicle contents may not be protected if the midgate is left open or ajar.
If the alarm does not sound when it should but the headlamps flash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers on page 6-103 . If the alarm does not sound or the headlamps do not flash, the vehicle should be serviced by your dealer/retailer.
If the engine does not start and the security light on the instrument panel cluster comes on when trying to start the vehicle, there may be a problem with your theft-deterrent system. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key.
Starting and Operating Your Vehicle New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Keep your speed at 55 mph (88 km/h) or less for the first 500 miles (805 km).
Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer.
Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition to START. When the engine starts, let go of the key. The idle speed will slow down as the engine warms. Do not race the engine immediately after starting it. Operate the engine and transmission gently to allow the oil to warm up and lubricate all moving parts.
Adjustable Throttle and Brake Pedal The vehicle has adjustable throttle and brake pedals that allow you change their positions. The feature will not operate when the vehicle is in R (Reverse) or while using the cruise control. The switch used to adjust the pedals is located on the center console below the climate control system.
To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located on the driver’s side of the engine compartment, near the power steering fluid reservoir. 3. Plug the cord into a normal, grounded 110-volt AC outlet.
Automatic Transmission Operation The vehicle has a Hydra-Matic ® 6L80 automatic transmission, and has an electronic shift position indicator within the instrument panel cluster. The electronic shift position indicator displays when the shift lever is moved out of P (Park).
To rock the vehicle back and forth to get out of snow, ice, or sand without damaging the transmission, see If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 5-29 . N (Neutral): In this position, the engine does not connect with the wheels. To restart when you are already moving, use N (Neutral) only.
The vehicle has a shift stabilization feature that adjusts the transmission shifting to the current driving conditions in order to reduce rapid upshifts and downshifts.
The DIC display will show the message MANUAL SHIFT on the first line and the current gear will be displayed on the second line. See Driver Information Center (DIC) on page 3-41 and DIC Operation and Displays on page 3-42 for more information. The number displayed in the DIC is the highest gear that can be used.
Also see “Tow Haul Mode” under Towing a Trailer on page 5-40 for more information. The tow/haul mode works with the Autoride ® feature, if the vehicle has this, to enhance the ride when trailering or with a loaded vehicle. See Autoride ® on page 5-39 .
Parking Brake For vehicles with a release handle, set the parking brake by holding the regular brake pedal down, then pushing down the parking brake pedal. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-33 .
For vehicles without a release handle, set the parking brake by holding the regular brake pedal down, then pushing down the parking brake pedal. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-33 .
Shifting Into Park { CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured.
Torque Lock If you are parking on a hill and you do not shift the transmission into P (Park) properly, the weight of the vehicle can put too much force on the parking pawl in the transmission. It might be diff icult to pull the shift lever out of P (Park).
Parking Over Things That Burn { CAUTION: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use.
Resetting the Power Foldaway Mirrors You may need to reset the power foldaway mirrors if: • The mirrors are accidentally obstructed while folding. • They are accidentally manually folded/unfolded. • The mirrors will not stay in the unfolded position.
Outside Convex Mirror { CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.
Object Detection Systems Ultrasonic Rear Parking Assist (URPA) For vehicles with the Ultrasonic Rear Parking Assist (URPA) system, it operates at speeds less than 5 mph (8 km/h), and assists the driver with parking and avoiding objects while in R (Reverse).
How the System Works URPA comes on automatically when the shift lever is moved into R (Reverse). The rear display briefly illuminates to indicate the system is working. URPA operates only at speeds less than 5 mph (8 km/h). If the vehicle is above this speed, the red light on the rear display will flash.
When the System Does Not Seem to Work Properly If the URPA system will not activate due to a temporary condition, the message PARK ASSIST OFF will be displayed on the DIC and a red light will be shown on the rear URPA display when the shift lever is moved into R (Reverse).
4. Select the Video screen button. When the Video screen button is highlighted the RVC system is on. The delay that is received after shifting out of R (Reverse) is approximately 10 seconds. The delay can be cancelled by performing one of the following: • Pressing a hard key on the navigation system.
To turn the symbols on or off: 1. Make sure that URPA has not been disabled. 2. Shift into P (Park). 3. Press the CONFIG hard key to enter the configure menu options, then press the CONFIG hard key repeatedly until Display is selected or touch the Display screen button.
Rear Vision Camera Location The image is provided by the camera located under the liftgate handle. The camera uses a special lens. The distance of the image that appears on the screen differs from the actual distance. The area displayed by the camera is limited.
When the System Does Not Seem To Work Properly The rear vision camera system might not work properly or display a clear image if: • The RVC is turned off. See “Turning the Rear Camera System On or Off” earlier in this section. • It is dark. • The sun or the beam of headlights is shining directly into the camera lens.
Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until the owner of the vehicle registers with OnStar. After the first prepaid year, contact OnStar to select a monthly or annual subscription payment plan.
a Bell Mobility service plan in Canada, depending on eligibility. To find out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit onstar.com or onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827).
for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times.
Universal Home Remote System Operation (With Three Round LED) This vehicle may have the Universal Home Remote System. If there are three round Light Emitting Diode (LED) indicator lights above the Universal Home Remote buttons, follow the instructions below.
Programming Universal Home Remote — Rolling Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
4. Immediately, within one second, release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 5. Press and release the same button again. The garage door should move, confirming that programming is successful and complete.
The garage door opener receiver (motor head unit) could also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head a.
2. Write down the eight to 12 switch settings from left to right as follows: • When a switch is in the up position, write “Left.” • When a switch is in the down position, write “Right.” • If a switch is set between the up and down position, write “Middle.
5. After entering all of the switch positions, again, firmly press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button that will be used to control the garage door until the garage door moves.
Storage Areas Glove Box Lift up on the glove box lever to open it. Cupholders Cupholders are located in the center console for the front passengers and on the back of the center console for the rear passengers. Press down and release the access door to use the front cupholders.
Do not exceed the maximum vehicle capacity when loading the vehicle. For more information on vehicle capacity and loading, see Loading the Vehicle on page 5-31 . Be sure the cargo is properly loaded. • If small heavy objects are placed on the roof, cut a piece of 3/8 inch plywood to fit inside the crossrails and siderails to spread the load.
Cargo Cover Panels The vehicle has a three-piece cargo cover system with cargo panels that can be removed and stored in the cargo area of the vehicle. { CAUTION: Improperly stored cargo cover panels could be thrown about the vehicle during a collision or sudden maneuver.
2. Unlock the cargo panel 3 by pulling forward on the driver side and passenger side cargo panel latches, located on the bottom of each cargo panel. 3. Remove cargo panel 2 in the same way and set it aside. Remove as many cargo panels as needed. 4. To remove cargo panel 1, unlock the two rear latches, lift the cover slightly and pull rearward.
To store the panels: 1. Secure the storage strap system in the cargo storage area by attaching the six clips on the cargo strap system to the tie down locations on either side of the storage area. Before storing the cargo panels, make sure that their latches are in the locked position.
2. Starting with cargo panel 1, load the cargo panel with the latches facing up toward the side of the cargo box. Do the same for cargo panel 2 then 3. Make sure to store panel 2 with the latches facing down and panel 3 with latches facing up toward the side of the cargo box.
4. Tighten all straps by pulling on the free end of each strap. 5. Close both cross locks at the center of the strap system to secure tightly. 2-72.
Reinstalling the Cargo Cover Panels The strap system can remain attached to the side of the cargo area while it is not in use, or it can be stored inside the top box storage compartment. See Top-Box Storage on page 2-81 for more information. To reinstall a cargo panel: 1.
Place the cover on the cargo box within 4 inches of the Midgate ® and lower the rear of the panel within 2 to 3 inches from the top of the cargo box. Push the cover forward making sure that the guide block engages the retainer bracket opening. Continue to push forward until the panel is fully seated against the Midgate.
3. Install cargo cover 2 followed by 3 next. Place the latches in the unlocked position. Place the cargo cover panel on the cargo area rails while holding the back of the cargo panel up. Push the panel forward until it is snug against the other panel and then let the back of the panel down making sure that the pegs (A) align with the receivers (B).
2. Fold the four primary strap ends towards the center as shown. 3. Take the short strap and surround the folded webbing, forming a package. 4. Take the secondary strap and wrap it around the folded webbing, forming a package. Finally, attach the hooks to the webbing and place inside the top box storage compartment.
Cargo Tie Downs Cargo tie downs in the rear cargo area can be used to secure cargo. All-Weather Cargo Area The vehicle’s cargo area can be used in many different configurations — cargo panels on or off, Midgate ® up or down, rear window in or out.
Maintenance and Cleaning To ensure that the water management system performs properly, be sure that the Midgate ® , tailgate and cover system are fully closed and that all parts are clean and not blocked with debris. Follow the instructions for the proper procedures on cleaning each item.
To replace the drain grate: 1. Line up the clips on the vehicle with the slots in the grate and firmly push the grate down. Do not force the grate. If it will not clip into place, realign the clips with the holes and try again. Side Rail Channels The side rail channels are located on top of both sides of the cargo area.
Midgate ® Drain Grate Removal and Cleaning The removable Midgate drain grate is located near the base of the Midgate. After hauling dirt, wood chips, pebbles etc. the Midgate drain should be flushed with water. First remove the drain grate by using the following steps: 1.
Cargo Area Floor Drains The cargo mat has cut-outs for the four cargo-area floor drains, located near the sides of the cargo area. Flush the drains periodically through the cutouts to clear debris and to allow water to drain from the cargo area.
Sunroof Your vehicle may be equipped with a power sliding sunroof. To open or close the sunroof, the ignition needs to be turned to ON/RUN, or Retained Accessory Power (RAP) must be active. When RAP is active, the sunroof will work for 10 minutes after the ignition is turned off, or until a front door is opened.
Vent: The sunroof has an express-vent open feature. From the closed position, press the rear of the passenger’s side switch to vent the sunroof. To stop the sunroof partway, press the switch a second time. To close the sunroof, press and hold the front of the passenger’s side switch.
✍ NOTES 2-84.
Instrument Panel Overview .............................. .3-4 Hazard Warning Flashers ............................... .3-5 H o r n ............................................................ .3-5 Tilt Wheel ...........................................
Cruise Control Light ..................................... .3-40 Highbeam On Light ...................................... .3-40 Tow/Haul Mode Light ................................... .3-41 Fuel Gage .................................................. .
✍ NOTES 3-3.
Instrument Panel Overview 3-4.
The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-26 . B. Turn Signal/Multifunction Lever on page 3-6 . C. Hazard Warning Flashers on page 3-5 . D. Instrument Panel Cluster on page 3-28 . E. Shift Lever/Tow/Haul Selector Button.
Tilt Wheel The power tilt wheel control is located on the left side of the steering column. Push the control up or down to tilt the steering wheel up or down. Heated Steering Wheel For vehicles with a heated steering wheel, the button for this feature is located on the steering wheel.
Turn and Lane-Change Signals An arrow on the instrument panel cluster flashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to flash to signal a lane change.
Flash-to-Pass This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. It works even if your headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it.
Since different drivers have dif ferent setting preferences, it is recommended that the mid-range setting, position three, be used initially. For more wipes, select the higher settings; for fewer wipes, select the lower settings located closer to the off position on the multifunction lever.
up to 20 seconds for each of the remaining cycles to begin. Press the button again to turn off the heated windshield washer fluid system or it will automatically turn off after four wipe cycles have been completed.
The cruise control buttons are located on left side of the steering wheel. T (On/Off): Turns the system on or of f. The indicator light is on when cruise control is on and turns off when cruise control is off. + RES (Resume/Accelerate): Press to make the vehicle accelerate or resume to a previously set speed.
Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, this shuts off the cruise control. But it does not need to be reset. Once the vehicle speed reaches about 25 mph (40 km/h) or more, press the +RES button on the steering wheel.
Ending Cruise Control There are three ways to end cruise control: • Step lightly on the brake pedal. • Press the [ button on the steering wheel. • Press the I button on the steering wheel. Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off.
2 (Headlamps): Turns on the headlamps together with the following lamps listed below. • Parking Lamps • Instrument Panel Lights • Taillamps • License Plate Lamps When the headlamps are turned on while the vehicle is on, the headlamps will turn off automatically 10 minutes after the ignition is turned off.
• The vehicle’s speed drops below 15 mph (24 km/h). • The headlamp stalk is moved forward to the high-beam position. See Headlamp High/Low-Beam Changer on page 3-7 .
Disabling and Resetting IntelliBeam ® at the Rearview Mirror IntelliBeam ® can be disabled by using the controls on the inside rearview mirror. AUTO 3 (On/Off): To disable the system, press this button on the inside rearview mirror.
Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system will come on when the following conditions are met: • The ignition is on.
If the vehicle is started in a dark garage, the automatic headlamp system will come on immediately. Once the vehicle leaves the garage, it takes approximately one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, the instrument panel cluster may not be as bright as usual.
Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located on the instrument panel to the left of the steering column, clockwise to the farthest position.
A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets.
The accessory power outlets are powered, even when the ignition is in LOCK/OFF. Continuing to use power outlets while the ignition is in LOCK/OFF may cause the vehicle’s battery to run down. Notice: Adding any electrical equipment to the vehicle can damage it or keep other components from working as they should.
Analog Clock The analog clock is located on the instrument panel above the radio. The clock is not connected with any other vehicle system and runs by itself. To adjust the clock: 1. The adjustment button is located in the lower left corner of the clock.
Press the up or down arrows on the fan switch, the defrost button, the AUTO button, driver side temperature knob, or the air conditioning button to turn the system on when it is off.
2. Set the driver’s and passenger’s temperature. To find your comfort setting, start with a 74°F (23°C) temperature setting and allow about 20 minutes for the system to regulate. Use the driver or passenger temperature buttons to adjust the temperature setting as necessary.
) (Bi-Level): Air is divided between the instrument panel and floor outlets. Some air is directed towards the windshield and side window outlets. Cooler air is directed to the upper vents and warmer air to the floor vents.
This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to help prevent outside air and odors from entering the vehicle. The recirculation mode cannot be used with floor, defog, or defrost modes. If recirculation is selected with one of those modes, the indicator light flashes three times and then turns off.
Operation Tips • Keep the hood and front air inlets free of ice, snow, or any other obstruction, such as leaves. The heater and defroster will work far better, reducing the chance of fogging the inside of your windows. • Keep the air path under the front seats clear of objects.
Instrument Panel Cluster The instrument panel cluster is designed to let show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel the vehicle has and many other things needed to drive safely and economically. United States version shown, Canada similar.
Speedometer and Odometer The speedometer shows the vehicle’s speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer works together with the Driver Information Center (DIC). Press the Trip/Fuel button on the instrument panel cluster to check the odometer mileage while the vehicle is not running.
Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime sounds for several seconds to remind the front passenger to buckle their safety belt. This only occurs if the passenger airbag is enabled. See Passenger Sensing System on page 1-61 for more information.
{ CAUTION: If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash.
If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag.
Brake System Warning Light With the ignition on, the brake system warning light comes on when the parking brake is set. If the vehicle is driven with the parking brake engaged, a chime sounds when the vehicle speed is greater than 3 mph (5 km/h). The vehicle’s hydraulic brake system is divided into two parts.
Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off.
Engine Coolant Temperature Gage This gage shows the engine coolant temperature. If the indicator on the gage moves towards the shaded area on the thermostat, it means that the engine coolant has overheated.
When the Light Flashes First and Then is On Steady This indicates that there could be a problem with the Tire Pressure Monitor System. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle.
This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required.
If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Gasoline Octane on page 6-5 . If none of the above have made the light turn off, your dealer/retailer can check the vehicle.
Oil Pressure Light { CAUTION: Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine.
Fog Lamp Light The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 3-18 for more information. Lights On Reminder This light comes on whenever the parking lamps are on. See Exterior Lamps on page 3-13 for more information.
Tow/Haul Mode Light This light comes on when the Tow/Haul mode has been activated. For more information, see Tow/Haul Mode on page 2-39 . Fuel Gage When the ignition is on, the fuel gage shows about how much fuel the vehicle has left in the tank. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on.
The DIC comes on when the ignition is on. After a short delay, the DIC will display the information that was last displayed before the engine was turned off. See DIC Operation and Displays on page 3-42 and DIC Vehicle Customization on page 3-56 for the displays available.
U (Customization): Press this button to customize the feature settings on your vehicle. See DIC Vehicle Customization on page 3-56 for more information. V (Set/Reset): Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC.
Fuel Used Press the trip/fuel button until FUEL USED displays. This display shows the number of gallons (gal) or liters (L) of fuel used since the last reset of this menu item. To reset the fuel used information, press and hold the set/reset button while FUEL USED is displayed.
When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See “CHANGE ENGINE OIL SOON” under DIC Warnings and Messages on page 3-48 . You should change the oil as soon as you can. See Engine Oil on page 6-15 .
This is normal. See Charging System Light on page 3-32 for more information. If there is a problem with the battery charging system, the DIC will display a message.
Compass Zone The zone is set to zone eight upon leaving the factory. Your dealer/retailer will set the correct zone for your location. Under certain circumstances, such as during a long distance cross.
Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. It is suggested to calibrate away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible.
Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear, not correct the problem.
ENGINE OIL HOT IDLE ENGINE This message displays when the engine oil becomes hotter than the normal operating temperature. Stop and allow the vehicle to idle until it cools down.
but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer/retailer for service as soon as possible. FUEL LEVEL LOW This message displays and a chime sounds if the fuel level is low. Refuel as soon as possible.
PARKING ASSIST OFF After the vehicle has been started, this message displays to remind the driver that the Ultrasonic Rear Parking Assist (URPA) system has been turned off. Press the set/reset button to acknowledge this message and clear it from the DIC display.
SERVICE BATTERY CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument panel cluster. See Charging System Light on page 3-32 .
SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system. The vehicle may or may not restart so you may want to take the vehicle to your dealer/retailer before turning off the engine. See PASS-Key ® III+ Electronic Immobilizer Operation on page 2-29 for more information.
• The message displays if an engine or vehicle related problem has been detected and the vehicle needs service. See your dealer/retailer. The message turns off as soon as the conditions that caused the message to be displayed are no longer present.
WASHER FLUID LOW ADD FLUID This message displays when the windshield washer fluid is low. Fill the windshield washer fluid reservoir as soon as possible. See Engine Compartment Overview on page 6-14 for the location of the windshield washer fluid reservoir.
DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature.
AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Programmable Automatic Door Locks on page 2-10 for more information.
HORN & LIGHTS (default): The exterior lamps will flash when you press the lock button on the RKE transmitter, and the horn will sound when the lock button is pressed again within five seconds of the previous command. NO CHANGE: No change will be made to this feature.
ON (default): The doors will not lock until five seconds after the last door or the tailgate is closed. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. AUTO HIGH BEAMS If your vehicle has this feature, it allows you to select to have the Intellibeam ® system turned off or on.
PARK TILT MIRRORS This feature allows you to select whether or not the outside mirror(s) will automatically tilt down when the vehicle is shifted into R (Reverse). See Outside Power Foldaway Mirrors on page 2-47 for more information. Press the customization button until PARK TILT MIRRORS appears on the DIC display.
NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. EASY EXIT SETUP If your vehicle has this feature, it allows you to select which areas will recall with the automatic easy exit seat feature.
REMOTE START If your vehicle has this feature, it allows you to turn the remote start off or on. The remote start feature allows you to start the engine from outside of the vehicle using the Remote Keyless Entry (RKE) transmitter. See Remote Vehicle Start on page 2-7 for more information.
FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Audio System(s) Read the following pages to become familiar with the audio system’s features. { CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Voice Recognition The Bluetooth system uses voice recognition to interpret voice commands to dial phone numbers and name tags. Noise: Keep interior noise levels to a minimum. The system may not recognize voice commands if there is too much background noise.
• The in-vehicle Bluetooth system automatically links with the first available paired cell phone in the order the phone was paired. • Only one paired cell phone can be connected to the in-vehicle Bluetooth system at a time.
Deleting a Paired Phone 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Delete”. The system asks which phone to delete followed by a tone.
If the number is correct, say “Yes”. If the number is not correct, say “No”. The system will ask for the number to be re-entered. 4. After the system stores the phone number, it responds with “Please say the name tag” followed by a tone. 5.
Using the Directory Command The directory command lists all of the name tags stored by the system. To use the directory command: 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Directory”. The system responds with “Directory” and then plays back all of the stored name tags.
Making a Call Calls can be made using the following commands: • Dial • Digit Dial • Call • Re-dial Using the Dial Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Dial using <phone name>.
3. Say the name tag of the person to call. • If the system clearly recognizes the name tag it responds with “OK, calling, <name tag>” and dials the number. • If the system is unsure it recognizes the right name tag, it confirms the name tag followed by a tone.
Three-Way Calling Three-Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. 1. While on a call press b g . The system responds with “Ready” followed by a tone. 2. Say “Three-way call”. The system responds with “Three-way call, please say dial or call”.
To Transfer Audio to the In-Vehicle Bluetooth System The cellular phone must be paired and connected with the Bluetooth system before a call can be transferred. The connection process can take up to two minutes after the key is turned to the ON/RUN or ACC/ACCESSORY position.
Sending a Stored Name Tag During a Call 1. Press b g . The system responds with “Ready” followed by a tone. 2. Say “Send name tag.” The system responds with “Say a name tag to send tones” followed by a tone.
Rear Seat Entertainment (RSE) System The vehicle may have an DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicle’s audio system. The DVD player is part of the front radio. The RSE system includes a radio with a DVD player, a video display screen, audio/video jacks, two wireless headphones, and a remote control.
jacks, or the auxiliary input jack, if the vehicle has this feature. The wireless headphones have an On/Off button, channel 1/2 switch, and a volume control. Push the power button to turn on the headphones. An indicator light located on the headphones comes on.
Audio/Video (A/V) Jacks The A/V jacks are located on the rear of the floor console. The A/V jacks allow audio or video signals to be connected from an auxiliary device such as a camcorder or a video game unit to the RSE system. Adapter connectors or cables (not included) may be required to connect the auxiliary device to the A/V jacks.
Audio Output Audio from the DVD player or auxiliary inputs can be heard through the following possible sources: • Wireless Headphones • Vehicle Speakers • Vehicle wired headphone jacks on the rear seat audio system, if your vehicle has this feature.
Remote Control To use the remote control, aim it at the transmitter window at the rear of the overhead console and press the desired button. Direct sunlight or very bright light can affect the ability of the RSE transmitter to receive signals from the remote control.
y (Main Menu): Press to access the DVD menu. The DVD menu is different on every DVD. Use the navigation arrows to move the cursor around the DVD menu. After making a selection press the enter button. This button only operates when using a DVD. Q , R , q , r (Menu Navigation Arrows): Use the arrow buttons to navigate through a menu.
e (Audio): Press to change audio tracks on DVDs that have this feature when the DVD is playing. The format and content of this function vary for each disc. { (Subtitles): Press to turn ON/OFF subtitles and to move through subtitle options when a DVD is playing.
Problem Recommended Action No power. The ignition might not be turned ON/RUN or in ACC/ACCESSORY. The picture does not fill the screen. There are black borders on the top and bottom or on both sides or it looks stretched out. Check the display mode settings in the setup menu by pressing the display menu button on the remote control.
DVD Display Error Messages The DVD display error message depends on which radio you have. The video screen might display one of the following: Disc Load/Eject Error: Displays when there are disc load or eject problems. Disc Format Error: Displays if the disc is inserted with the disc label wrong side up, or if the disc is damaged.
Audio can be heard through wired headphones (not included) plugged into the jacks on the RSA. If your vehicle has this feature, audio can also be heard on Channel 2 of the wireless headphones. The front audio system allows the rear speakers to continue playing even when the RSA audio is active through the headphones.
©¨ (Seek): When listening to FM, AM, or XM (if equipped), press the seek arrows to go to the previous or to the next station or channels and stay there. This function is inactive, with some radios, if the front seat passengers are listening to the radio.
Audio Steering Wheel Controls Vehicles with audio steering wheel controls could differ depending on the vehicle’s options. Some audio controls can be adjusted at the steering wheel. w (Next): Press to go to the next radio station stored as a favorite, or the next track if a CD/DVD is playing.
Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Fixed Mast Antenna The fixed mast antenna can withstand most car washes without being damaged as long as it is securely attached to the base. If the mast becomes slightly bent, straighten it out by hand. If the mast is badly bent, replace it. Occasionally check to make sure the antenna is tightened to its base.
Overview ........................................................ .4-2 Navigation System Overview ........................... .4-2 Getting Started .............................................. .4-4 Cleaning the Display ...............................
Overview Navigation System Overview Screen shown with Map Disc Inserted 4-2.
A. Source (AM, FM, XM, CD, etc.) Touch Screen Button. See Navigation Audio System on page 4-57 for more information. B. Clock Touch Screen Button. See “Setting the Clock” under Configure Menu on page 4-40 for more information. C. POI (Point of Interest) Touch Screen Button.
T. Map DVD Slot. See “Installing the Map DVD” under Maps on page 4-14 for information on how to install and eject a map DVD. U. Z (DVD Map Disc Eject) Key. See Maps on page 4-14 for more information. V. Mark Touch Screen Button. See “Adding Destinations to the Address Book” under Destination on page 4-23 for more information.
• Set up the navigation features before beginning driving, such as entering an address or a preset destination. • Set up your phone numbers in advance so they can be called easily with the press of a single button or a single voice command (for navigation systems equipped with phone capability).
When the navigation system is turned on, a screen may appear with the information below, and you must read and acknowledge the information it contains. { CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others.
Language — English/Metric To change the language of the navigation screens, see Driver Information Center (DIC) on page 3-41 for more information. To change the navigation screens from English or metric, see DIC Operation and Displays on page 3-42 for more information.
Setting the Clock The navigation system time and the analog clock operate independently. Changing the time through the navigation system does not change the time on the analog clock. See Analog Clock on page 3-22 to change the analog clock time. To set the time for the navigation system: 1.
displays a number. This button represents the number of available streets. Select this button to view the list and select a street. 10. Once a street has been selected, select the House # screen button to enter the house number. The system displays the house number range that is available for the street.
Storing Preset Destinations 1. If the radio is already on with a map disc inserted, skip to Step 5. 2. Press O to turn the system on. 3. Insert the DVD map disc. See “Installing the Map DVD” under Maps on page 4-14 for more information. 4. A caution may appear.
7. Select the route preference (Fastest, Shortest, or Other). The system calculates and highlights the route. 8. Select the Start Guidance screen button. The route is now ready to be started. See “Preset Destination” under Destination on page 4-23 for more information.
Hard Keys The following hard keys are located on the navigation system: O / n (Power/Volume): Press to turn the system on and off. Turn to increase or decrease the volume to the audio system. Press and hold for more than two seconds to turn off the navigation system, the Rear Seat Entertainment (RSE), and Rear Seat Audio (RSA).
CONFIG (Configure Menu): Press to adjust features for sound, radio, navigation, and the display. See Configure Menu on page 4-40 for more information.
Maps This section includes basic information that you need to know about the map database. The maps are stored on a DVD. The United States, Canada, and Puerto Rico are contained on one disc. Detailed Areas Road network attributes are contained in the map database for detailed areas.
• You are driving on a very rough road. When the road becomes smoother, the map disc should play. • The map disc is dirty, scratched, wet, or upside down. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer/retailer.
Scrolling the Map Touch anywhere on the map screen and the scroll symbol appears. Use this feature to scroll across the map. Move your finger in any direction on the map screen and the map continues to scroll in that direction until you remove your finger from the screen.
The stopover symbol displays on the map after a stopover has been added to the route. The stopover symbols are numbered one through three, depending on how many stopovers have been set. The distance to destination symbol indicates the distance to the final destination.
The north up symbol indicates the map with North Up, known as North Up mode. While in North Up mode, the vehicle icon follows the north direction on the map regardless of which direction the vehicle is traveling. Select this screen symbol to switch between North Up, Heading Up, and 3–D view modes.
Displaying Points of Interest (POI) on the Map Screen Select the POI screen button to display or delete POI icons from the map. Displaying POI icons on the map shows where POIs (e.g. restaurants, gas stations, etc.) are located. This screen appears after selecting the POI screen button.
POI Close to: 1. Once a category has been selected, touch this button to display the list of available POIs for the selected POI category. The list provides the POI icon, the name, the direction, and the distance to the POI from the vehicle’s current position.
Driving on a Route When driving on a routed destination, the map screen automatically displays the next maneuver. The pop-up displays the next maneuver direction and the distance from it. When approximately 1/4 mi (400 m) from the next maneuver, the screen displays the name and a detailed view of it.
3–D Lane Guidance Some major metropolitan areas may include a 3–D lane guidance feature for highway exits and junctions. This feature gives you an enhanced representation of the exits and junctions on the route.
Destination Press the DEST key to access the Destination Entry screen. From this screen, you can select from several options to plan a route by entering destination points.
The Last 5 Cities screen displays a list of the last five city names that had been entered. Select a city from the list and it appears in the City name area. If using the alpha keyboard, finish entering the city name. If five or less names are available, a list displays.
5. Once a street has been selected, select the House # screen button to enter the house number. The system displays the house number range that is available for the street. 6. Once the house number is selected, the city name automatically populates. If there is more than one city available for selection, a list of cities display.
8. Select the Start Guidance screen button. The route is now ready to be started. See “Getting Started on Your Route” later in this section for more information. Point of Interest (POI) The Point of Interest (POI) destination entry method lets you select a destination from the POI list.
To use the point of interest destination entry method by selecting a category: 1. Press the DEST hard key. 2. Select the i screen button. 3. Select the Browse POI Categories screen button to view the list of POI categories. 4. Select a category. The system displays available POI names in the selected category.
4. Select the route preference (Fastest, Shortest, or Other). The system calculates and highlights the route. 5. Select the Start Guidance screen button. The route is now ready to be started. See “Getting Started on Your Route” later in this section for more information.
From Map This destination entry method allows you to select a destination by scrolling on the map. ) From Map: Touch to enter the From Map destination entry method. To use this destination entry method: 1. Press the DEST hard key. 2. Select the ) screen button.
Map Coordinates The coordinates destination entry method lets you select a destination by entering latitude and longitude coordinates. Map Coordinates: Touch to access the Coordinates Entry screen. To use the coordinates destination entry method: 1. Press the DEST hard key.
Preset Destination The preset destination entry method lets you set a destination by selecting from one of five previously stored destinations. Besides voice tagged destinations, these are the only destinations available to set while the vehicle is moving.
Map Destination Screen Functions If the map screen is used to show destination, it will have map screen capabilities such as Go, Mark, Zoom, Scroll, etc.
Using OnStar ® Destination Download Press the blue OnStar button and an Advisor can locate a point-of-interest or an address and download the necessary information or coordinates to your navigation system. Once the destination is downloaded, the navigation system will search for the address in the mapping disc’s database.
Route Guidance Not Active If an OnStar destination is downloaded while route guidance is not active, the navigation system displays an OnStar Destination Download Screen and operations will continue a.
Map Destination Screen Functions If the map screen is used to show destination, it will have map screen capabilities such as Go, Mark, Zoom, Scroll, etc. The address is shown at the top of the screen. Getting Started on Your Route Once a destination has been entered, there are several functions that can be performed.
Turn List Turn List: Touch to view the list of turn maneuvers for the entire route and to avoid turns on the route. r / q (Scroll Arrows): Touch the up and down arrows to scroll through the list of maneuvers. Avoid: Touch this screen button, next to the adjacent street name, to avoid the maneuver.
r / [ (Fast Forward Scroll): Select to scroll to the next stopover or to the final destination. The u (fast forward skip) button changes to a fast speed fast forward. u (Fast Forward Skip): Select to go to the next stopover or to the final destination.
To add a stopover: 1. Press the DEST hard key. 2. Select the Add Stopover screen button. This button only appears if a route has been calculated. 3. Using the desired method of entering a destination, enter the stopover. See “Destination” previously for more information.
Adding Destinations to the Address Book There are two ways to add a destination to the address book: • To add the current vehicle position to the address book, press the Mark screen button from the map screen. The system automatically saves the current vehicle information in the address book.
Configure Menu Press the CONFIG (Configure) hard key to adjust several of the system’s features and preferences. The last selected CONFIG screen is the screen that displays: Sound, Radio, Nav (navigation), Display, or Time.
Nav (Navigation) Press the CONFIG key to enter the configure menu options, then press the CONFIG key repeatedly until Nav is selected or touch the Nav screen button. Voice Prompt Voice Prompt: Touch the Voice Prompt screen button to change the volume of the voice prompts or to turn voice guidance on and off.
Edit Address Book — Edit/View To edit the name of an address book: 1. Select the CONFIG hard key. 2. Select the NAV screen button. 3. Select the Edit/View Address Book screen button. 4. Select the Address book entry. 5. Touch the Name screen button and use the alpha keyboard to edit or add the name.
4. Select the Add Voice Tag screen button. 5. The system will ask for you to state the name. You will have four seconds to state the name. The system will respond back with the name and prompt you to repeat the name for confirmation. To delete an address book entry: 1.
When the off-road mode is turned on, the navigation system will show the path being traveled by the vehicle when not on a marked road. This path will be a simulation since the map database coverage will not have these roads on the DVD.
Traff ic information is delivered to the vehicle by the XM™ Radio satellites. XM NavTraff ic™ makes it possible for the navigation system to provide continuously updated traff ic information personalized for a driver’s needs.
Condition Traff ic Status Icon Traff ic events are in the area, but none are on route. Traff ic events are on route. Locations and Information of Traf fic Conditions The system may take some time to sort the information. The list of traff ic conditions display in the order of distance from the vehicle, up to approximately 75 mi (125 km).
appears, the distance indicates how far the event is ahead on current Interstate highway or route. While the vehicle is moving, the traff ic list up or down, scroll arrows are limited to a maximum of four pages. No more than four pages of traff ic events may be viewed while the vehicle is moving.
Traff ic Flow Status — This touch screen button is used to enable or disable the green, yellow, red and orange arrows shown beside the roads and used to show the traff ic flow or extent of a traffic event. • Black indicates a closed road segment • Red indicates significantly impaired traff ic flow with average speed of less than 25 mph.
On-Route Select the On Route touch screen button to display all events ahead on the current active route. If no traff ic events have been reported on route, No Traff ic Events Reported On route displays. Name Select the Name touch screen button to display traff ic events in the order of distance.
After selecting the INFO (information) screen button, the type of traff ic condition, the street name, and a description of the traff ic condition displays.
Detailed Traf fic Event Screens The detailed Traff ic Event screens are used to display additional details of a traff ic event condition. This screen may display if: • Scrolling to an event on the map and then pressing INFO. • Selecting a traff ic event listed on the Traffic Event List screen.
Avoid: This button is used to avoid the location of an event on the route. If selected, a new route is calculated and the related traff ic event is avoided. After the new route has been calculated, the navigation system goes to the full map screen and shows the new route.
Brightness/Contrast/Mode Touch this screen button to change the brightness, contrast, and mode of the display. ] (Brightness): Touch the + (plus) or − (minus) screen buttons to increase or decrease the brightness of the screen. _ (Contrast): Touch the + (plus) or − (minus) screen buttons to increase or decrease the contrast of the screen.
Global Positioning System (GPS) The navigation system determines the position of the vehicle by using satellite signals, various vehicle signals, and map data.
• Current position calibration is set incorrectly. • Vehicle is traveling at high speed. • Vehicle changes directions more than once, or when the vehicle is turning on a turn table in a parking lot. • Vehicle is entering and/or exiting a parking lot or a garage.
• Some routes may not be searched. • The route to the destination may not be shown if there are new roads, if roads have recently changed, or if certain roads are not listed on the map DVD. See Ordering Map DVDs on page 4-56 . To recalibrate the vehicle’s position on the map, see your dealer/retailer.
Navigation Audio System Notice: Before adding any sound equipment to the vehicle, such as an audio system, CD player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer/retailer. Also, check federal rules covering mobile radio and telephone units.
Finding a Station If viewing a map screen, touch the source screen (AM, FM, XM, CD, etc.) button. The display splits between the audio screen and the map screen. All station-changing functions can be performed from this screen. If you do not want to view a split screen or you are not on a map screen, press the AUDIO hard key.
Category: Touch the screen button, located in the middle of the screen, to receive a list of all of the selected band stations in the area. Use the up and down arrows to scroll the frequencies. Touch the desired frequency. XM lists also contain a category to select and the stations or channels that have broadcasts that relate to that category.
4. Seek, scan, or tune to the desired station, to select the station. 5. Press and hold one of the preset screen buttons for more than two seconds or until a beep is heard.
Digital Signal Processing (DSP) The system has Digital Signal Processing (DSP). DSP provides a choice of four different listening experiences. DSP can be used while listening to the audio system. Not all DSP modes are available for all source types. The type of DSP selected is displayed on the status line.
Limit Features While Driving Touch the Limit Features While Driving screen button to turn on and off the ability to limit functions while driving. When this screen button is highlighted, the following.
Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information.
No Artist Info: No artist information is available. The system is working properly. No Title Info: No song title information is available. The system is working properly. No CAT Info: No category information is available. The system is working properly.
M (Load): To load one disc, do the following: 1. Press the load hard key and follow the screen message displayed. 2. When the system displays “Insert Disc (number)”, insert the disc partway into the slot, label side up. The system will pull it into the first available slot and start playing.
Playing an Audio CD j / r (Pause/Play): Touch this button to pause the CD. This button will then change to the play button. Touch the play button to play the CD. Random: Touch this button to hear the tracks in random, rather than sequential, order. Touch Random again to turn off random play.
Using an MP3 CD MP3 Format There are guidelines that must be met, when creating an MP3 disc. If the guidelines are not met when recording a CD-R(W), the CD may not play. The guidelines are: • Sampling rate: 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, and 44.
Order of Play Play will begin from the first track under the root directory. When all tracks from the root directory have been played, play will continue from files according to their numerical listing. After playing the last track from the last folder, play will begin again at the first track of the first folder or root directory.
To load multiple discs, do the following: 1. Press and hold the load hard key and follow the screen message displayed. 2. When the system displays “Insert Disc (number)”, insert the disc partway into the slot, label side up. The system will pull it in.
[ (Forward): Touch and hold this button to fast forward quickly through a track selection. You will hear sound at a reduced volume. Release this button to stop fast forwarding.
DVD Player The player can be used for DVD audio and DVD video. DVD video will not display on the navigation screen unless the vehicle is in PARK (P). It will operate on the rear seat entertainment screens while the vehicle is moving.
Z (Eject): To eject a disc, do the following: 1. Press the eject hard key. 2. The system will display “Ejecting Disc”. Press the DISC screen button to display the Disc Changer screen. Select the disc to eject. If a selection is not made, the system will eject the disc from the current slot.
Enter: Touch this button to select the highlighted option. Return: Touch this button to go back to the previous DVD menu. Back: Touch this button to go back to the main DVD display screen. Move: Touch this button to move the cursor buttons back and forth from the bottom-right corner to the top-left corner of the screen.
Menu: Touch this button to display the DVD menu of the current area of the DVD that is playing. This button is not available for DVD audio. Audio: Press this button to display the audio options. Select the audio options that best improve sound quality.
Day: Touch this screen button and the system will make the navigation screen background darken. Monitor: From the DVD Setup screen, touch this button to adjust the viewing angle of the DVD on the navigation screen.
Menu Language: Touch English, Francais, Espanol, Italiano, or Deutsch to change the default language of the DVD video menus. The menu language must be available on the disc. The menu language may vary for each DVD. Parental Level: Touch this button to change the rating level to only allow the play of DVDs with a certain rating.
• It is very hot. When the temperature returns to normal, the DVD should play. • You are driving on a very rough road. When the road becomes smoother, the DVD should play. • The DVD is dirty, scratched, wet, or upside down. • The air is very humid.
Auxiliary Devices The vehicle may have a rear entertainment system (RSE) with a second and third row screen. The RSE has audio adapters to allow you to connect auxiliary devices. The audio can be heard through the speakers or through the wireless or wired headphones.
Voice recognition can be used when the ignition is on or when Retained Accessory Power (RAP) is active. See “Retained Accessory Power (RAP)” in the Index of your vehicle’s owner manual for more information. To use voice recognition, do the following: 1.
This system is able to recognize commands in three different languages. The system only recognizes commands based on the language selected from the Driver Information Center (DIC).
Radio Commands The following are radio commands that can be accessed by clearly stating the commands exactly as they are written. Radio [band] [select] AM, radio [band] [select] FM, radio [band] [select] XM, radio [band] [select] satellite: Instructs the system to go to either the AM, FM, or XM (if equipped).
✍ NOTES 4-82.
Your Driving, the Road, and the Vehicle ........... .5-2 Driving for Better Fuel Economy ...................... .5-2 Defensive Driving .......................................... .5-2 Drunk Driving ................................................ .5-3 Control of a Vehicle .
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops.
Drunk Driving { CAUTION: Drinking and then driving is very dangerous. Your reflexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking.
Braking See Brake System Warning Light on page 3-33 . Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second.
Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that will help prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on.
Braking in Emergencies ABS allows the driver to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking. Brake Assist This vehicle has a Brake Assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions.
If the system fails to turn on or activate, the StabiliTrak light along with one of the following messages will be displayed on the Driver Information Center (DIC): TRACTION CONTROL OFF, SERVICE TRACTION CONTROL, STABILITRAK OFF, SERVICE STABILITRAK.
It is recommended to leave the system on for normal driving conditions, but it may be necessary to turn the system off if the vehicle is stuck in sand, mud, ice or snow, and you want to “rock” the vehicle to attempt to free it.
Magnetic Ride Control™ The vehicle may have the MagneRide control system. MagneRide constantly checks speed, wheel position, lift/dive and steering of the vehicle. The damping force for each shock absorber and adjustment level is chosen for the best ride and handling.
Steering Tips It is important to take curves at a reasonable speed. Traction in a curve depends on the condition of the tires and the road surface, the angle at which the curve is banked, and vehicle speed. While in a curve, speed is the one factor that can be controlled.
Of f-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems.
Drinking and driving can be very dangerous on any road and this is certainly true for off-road driving. At the very time you need special alertness and driving skills, your reflexes, perceptions, and judgment can be affected by even a small amount of alcohol.
If you think you will need some more ground clearance at the front of your vehicle, you can remove the front fascia lower air dam. The air dam is held in place by two bolts and 10 snaps accessible from underneath the front fascia. To remove the air dam: 1.
There are some important things to remember about how to load your vehicle. • The heaviest things should be on the floor, forward of the rear axle. Put heavier items as far forward as you can. • Be sure the load is properly secured, so things are not tossed around.
Controlling the vehicle is the key to successful off-road driving. One of the best ways to control the vehicle is to control the speed. At higher speeds: • You approach things faster and have less time to react. • There is less time to scan the terrain for obstacles.
Because you will be on an unpaved surface, it is especially important to avoid sudden acceleration, sudden turns, or sudden braking. Off-roading requires a dif ferent kind of alertness from driving on paved roads and highways. There are no road signs, posted speed limits, or signal lights.
Driving Uphill Once you decide it is safe to drive up the hill: • Use a low gear and get a firm grip on the steering wheel. • Get a smooth start up the hill and try to maintain speed. Not using more power than needed can avoid spinning the wheels or sliding.
• If the engine has stopped running, you need to restart it. With the brake pedal pressed and the parking brake still applied, shift the transmission to P (Park) and restart the engine. Then, shift to R (Reverse), release the parking brake, and slowly back down the hill as straight as possible in R (Reverse).
Driving Downhill When off-roading takes you downhill, consider: • How steep is the downhill? Will I be able to maintain vehicle control? • What is the surface like? Smooth? Rough? Slippery? Hard-p.
Driving Across an Incline An off-road trail will probably go across the incline of a hill. To decide whether to try to drive across the incline, consider the following: { CAUTION: Driving across an incline that is too steep will make your vehicle roll over.
Stalling on an Incline { CAUTION: Getting out on the downhill (low) side of a vehicle stopped across an incline is dangerous. If the vehicle rolls over, you could be crushed or killed. Always get out on the uphill (high) side of the vehicle and stay well clear of the rollover path.
Driving in Water { CAUTION: Driving through rushing water can be dangerous. Deep water can sweep your vehicle downstream and you and your passengers could drown. If it is only shallow water, it can still wash away the ground from under your tires, and you could lose traction and roll the vehicle over.
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive.
CAUTION: (Continued) Flowing or rushing water creates strong forces. Driving through flowing water could cause your vehicle to be carried away. If this happens, you and other vehicle occupants could drown. Do not ignore police warnings and be very cautious about trying to drive through flowing water.
Highway Hypnosis Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy, find a safe place to park your vehicle and rest. Other driving tips include: • Keep the vehicle well ventilated. • Keep interior temperature cool.
{ CAUTION: Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down and they could get so hot that they would not work well. You would then have poor braking or even none going down a hill.
Allow greater following distance on any slippery road and watch for slippery spots. Icy patches can occur on otherwise clear roads in shaded areas. The surface of a curve or an overpass can remain icy when the surrounding roads are clear. Avoid sudden steering maneuvers and braking while on ice.
Run the engine for short periods only as needed to keep warm, but be careful. To save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel really uncomfortable from the cold.
a few tries, it might need to be towed out. Recovery hooks can be used, if the vehicle has them. If the vehicle does need to be towed out, see Towing Your Vehicle on page 5-37 . Recovery Hooks { CAUTION: These hooks, when used, are under a lot of force.
Loading the Vehicle It is very important to know how much weight the vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options.
For more information on tires and inflation see Tires on page 6-54 and Inflation - Tire Pressure on page 6-60 . There is also important loading information on the vehicle Certification/Tire label. It tells you the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for the front and rear axles.
Item Description Total A Vehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Cargo Weight = 700 lbs (.
Item Description Total A Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle’s tire and loading information label for specific information about your vehicle’s capacity weight and seating positions.
The Certification/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To find out the actual loads on the front and rear axles, you need to go to a weigh station and weigh the vehicle. Your dealer/retailer can help you with this.
If you put things inside the vehicle — like suitcases, tools, packages, or anything else — they go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. { CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.
connected to the rear shocks will raise or lower the rear of the vehicle to maintain proper vehicle height. The system is activated when the ignition key is turned to ON/RUN and will automatically adjust vehicle height thereafter. The system may exhaust (lower vehicle height) for up to 10 minutes after the ignition key has been turned to OFF/LOCK.
Dinghy Towing and Dolly Towing All-Wheel Drive Vehicles Notice: Towing an all-wheel-drive vehicle with all four wheels on the ground, or even with only two of its wheels on the ground, will damage drivetrain components. Do not tow an all-wheel-drive vehicle with any of its wheels on the ground.
Level Control Automatic Level Control The automatic level control rear suspension is available on light-duty vehicles and comes as a part of the Autoride ® suspension, if equipped.
Towing a Trailer Do not tow a trailer during break-in. See New Vehicle Break-In on page 2-31 for more information. { CAUTION: The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly.
Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
Weight of the Trailer How heavy can a trailer safely be? It depends on how the rig is used. For example, speed, altitude, road grades, outside temperature and how much the vehicle is used to pull a trailer are all important. It can depend on any special equipment on the vehicle, and the amount of tongue weight the vehicle can carry.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Consider the following example: A vehicle model base weight is 5,500 lbs (2 495 kg); 2,800 lbs (1 270 kg) at the front axle and 2,700 lbs (1 225 kg) at the rear axle. It has a GVWR of 7,200 lbs (3 266 kg), a RGAWR of 4,000 lbs (1 814 kg) and a GCWR (Gross Combination Weight Rating) of 14,000 lbs (6 350 kg).
least 10 percent of total loaded trailer weight, expect that the largest trailer the vehicle can properly handle is 6,000 lbs (2 721 kg). It is important that the vehicle does not exceed any of its ratings — GCWR, GVWR, RGAWR, Maximum Trailer Rating or Tongue Weight.
When pulling a trailer that, when loaded, will weigh more than 5,000 lbs (2 270 kg) be sure to use a properly mounted weight-distributing hitch and sway control of the proper size. This equipment is very important for proper vehicle loading and good handling when driving.
Tow/Haul is designed to be most effective when the vehicle and trailer combined weight is at least 75 percent of the vehicle’s Gross Combined Weight Rating (GCWR).
Driving with a Trailer { CAUTION: When towing a trailer, exhaust gases may collect at the rear of the vehicle and enter if the liftgate, trunk/hatch, or rear-most window is open. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled.
Backing Up Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, move that hand to the left. To move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you.
Parking on Hills { CAUTION: Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.
Trailer Wiring Harness Heavy-Duty Trailer Wiring Package The vehicle is equipped with the seven-wire trailer towing harness. This harness with a seven-pin universal heavy-duty trailer connector is attached to the rear bumper beam. It is located next to the integrated trailer hitch.
Electric Brake Control Wiring Provisions These wiring provisions are included with the vehicle as part of the heavy-duty trailer wiring package. These provisions are for an electric brake controller.
Service ........................................................... .6-3 Accessories and Modifications ......................... .6-3 California Proposition 65 Warning .................... .6-4 California Perchlorate Materials Requirements .... .6-4 Doing Your Own Service Work .
Tire Pressure Monitor System ........................ .6-62 Tire Pressure Monitor Operation .................... .6-63 Tire Inspection and Rotation .......................... .6-67 When It Is Time for New Tires ...................... .6-68 Buying New Tires .
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories an.
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
This vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your Airbag-Equipped Vehicle on page 1-67 . Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7-17 .
Gasoline Specifications At a minimum, gasoline should meet ASTM specification D 4814 in the United States or CAN/CGSB-3.5 or 3.511 in Canada. Some gasolines contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT).
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel.
Fuel E85 (85% Ethanol) This vehicle can use either unleaded gasoline or 85% ethanol fuel (E85). We encourage the use of E85 in vehicles that are designed to use it. The ethanol in E85 is a “renewable” fuel, meaning it is made from renewable sources such as corn and other crops.
Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel might be hard to find. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty.
The tethered fuel cap is located behind a hinged fuel door on the driver side of the vehicle. If the vehicle has E85 fuel capability, the fuel cap will be yellow and state that E85 or gasoline can be used. See Fuel E85 (85% Ethanol) on page 6-8 . To remove the fuel cap, turn it slowly counterclockwise.
The TIGHTEN GAS CAP message displays on the Driver Information Center (DIC) if the fuel cap is not properly installed. See DIC Warnings and Messages on page 3-48 for more information. { CAUTION: If a fire starts while you are refueling, do not remove the nozzle.
Checking Things Under the Hood { CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION: Things that burn can get on hot engine parts and start a fire.
Hood Release To open the hood: 1. Pull the handle with this symbol on it. It is located inside the vehicle to the lower left of the steering wheel. 2. Then go to the front of the vehicle and locate the secondary hood release, near the center of the grille.
Engine Compartment Overview When you open the hood on the 6.2L engine this is what you will see: 6-14.
A. Engine Air Cleaner/Filter on page 6-19 . B. Coolant Surge Tank and Pressure Cap. See Cooling System on page 6-25 . C. Remote Positive (+) Terminal. See Jump Starting on page 6-40 . D. Battery on page 6-39 . E. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 6-15 .
When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 6-110 .
What Kind of Engine Oil to Use Look for three things: • GM4718M This vehicle’s engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identified as synthetic. However, not all synthetic oils will meet this GM standard.
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM standards are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty.
If the CHANGE ENGINE OIL SOON message comes back on when the vehicle is started, the Engine Oil Life System has not reset. Repeat the procedure. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer.
Replacing the Engine Air Cleaner/Filter 1. Locate the air cleaner/filter assembly. See Engine Compartment Overview on page 6-14 . 2. Loosen the four screws on the cover of the housing and lift up the cover. 3. Remove the engine air cleaner/filter from the housing.
{ CAUTION: Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. If it is not there and the engine backfires, you could be burned.
3. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, move the shift lever back to P (Park). 4. Allow the engine to idle (500 – 800 rpm) for at least one minute. Slowly release the brake pedal.
5. If the fluid level is below the COLD check band, add only enough fluid as necessary to bring the level into the COLD band. It does not take much fluid, generally less than one pint (0.
4. Check both sides of the dipstick and read the lower level. Repeat the check procedure to verify the reading. 5. Safe operating level is within the HOT cross hatch band on the dipstick.
Cooling System The cooling system allows the engine to maintain the correct working temperature. A. Coolant Surge Tank B. Coolant Surge Tank Pressure Cap C. Engine Cooling Fan(s) { CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and CAUTION: (Continued) CAUTION: (Continued) can cause injury.
Engine Coolant The cooling system in the vehicle is filled with DEX-COOL ® engine coolant. This coolant is designed to remain in the vehicle for five years or 150,000 miles (240 000 km), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low.
Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant surge tank. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down.
How to Add Coolant to the Surge Tank { CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Notice: This vehicle has a specific coolant fill procedure.
If no coolant is visible in the surge tank, add coolant as follows: 1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one full turn.
4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan.
You may decide not to lift the hood when this warning appears, but instead get service help right away. See Roadside Service on page 8-7 . If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running.
If No Steam Is Coming From The Engine Compartment The ENGINE OVERHEATED STOP ENGINE or the ENGINE OVERHEATED IDLE ENGINE message, along with a low coolant condition, can indicate a serious problem. If you get an engine overheat warning, but see or hear no steam, the problem may not be too serious.
Overheated Engine Protection Operating Mode If an overheated engine condition exists and the ENGINE POWER IS REDUCED message is displayed, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage. In this mode, you will notice a loss in power and engine performance.
When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired.
Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 6-14 for reservoir location. Notice: • When using concentrated washer fluid, follow the manufacturer’s instructions for adding water.
Do not top off the brake fluid. Adding fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as necessary, only when work is done on the brake hydraulic system.
What to Add Use only new DOT-3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 7-13 . Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking.
Jump Starting If the vehicle’s battery (or batteries) has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you.
Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3. Turn off the ignition on both vehicles.
{ CAUTION: An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. { CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded.
Do not connect positive (+) to negative ( − )o ry o u will get a short that would damage the battery and maybe other parts too. And do not connect the negative ( − ) cable to the negative ( − ) terminal on the dead battery because this can cause sparks.
Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
All-Wheel Drive Transfer Case If your vehicle is equipped with All-Wheel Drive, be sure to perform the lubricant checks described in this section. There are two additional systems that need lubrication. When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant.
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 7-13 . Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle fluid unless you suspect there is a leak or you hear an unusual noise.
Front Axle When to Check and Change Lubricant It is not necessary to regularly check front axle fluid unless you suspect there is a leak or you hear an unusual noise. A fluid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 7-13 . Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim of the headlamps have been preset at the factory and should need no further adjustment.
Headlamp aiming is done with the vehicle’s low-beam headlamps. The high-beam headlamps will be correctly aimed if the low-beam headlamps are aimed properly. To adjust the vertical aim: 1. Open the hood. See Hood Release on page 6-13 for more information.
7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly. The adjustment screw can be turned with a E8 Torx ® socket. 8. Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line.
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 6-53 . For any bulb changing procedure not listed in this section, contact your dealer/retailer. High Intensity Discharge (HID) Lighting { CAUTION: The low beam high intensity discharge lighting system operates at a very high voltage.
2. Remove the two screws from the taillamp assembly. 3. Pull the taillamp assembly straight back to remove. 4. Turn the bulb socket counterclockwise to remove it from the taillamp assembly.
Replacement Bulbs Exterior Lamp Bulb Number Back-up Lamp 7441 License Plate Lamp 168 Sidemarker Lamp 194 Stoplamp/Taillamp/Turn Signal Lamp 3057 For replacement bulbs not listed here, contact your dealer/retailer. Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking.
3. Install the new blade onto the arm connector and make sure the grooved areas are fully set in the locked position. For the proper type and size, see Maintenance Replacement Parts on page 7-15 . Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer.
CAUTION: (Continued) Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold. See Inflation - Tire Pressure on page 6-60 . • Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when you hit a pothole.
(B) TPC Spec (Tire Performance Criteria Specification) : Original equipment tires designed to GM’s specific tire performance criteria have a TPC specification code molded onto the sidewall. GM’s TPC specifications meet or exceed all federal safety guidelines.
(C) Aspect Ratio : A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 75, as shown in item C of the light truck (LT-Metric) tire illustration, it would mean that the tire’s sidewall is 75% as high as it is wide.
DOT Markings : A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) motor vehicle safety standards.
Passenger (P-Metric) Tire : A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure : Vehicle manufacturer’s recommended tire inflation pressure as shown on the tire placard. See Inflation - Tire Pressure on page 6-60 and Loading the Vehicle on page 5-31 .
Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right.
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are underinflated. Check the tire’s inflation pressure when the tires are cold.
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle.
Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.
The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as you start to drive. This could be an early indicator that the air pressure in the tire(s) are getting low and need to be inflated to the proper pressure.
• One or more TPMS sensors are missing or damaged. The DIC message and the TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer/retailer for service. • Replacement tires or wheels do not match your vehicle’s original equipment tires or wheels.
The TPMS sensor matching process is outlined below: 1. Set the parking brake. 2. Turn the ignition switch to ON/RUN with the engine off. 3. Press the Remote Keyless Entry (RKE) transmitter’s lock and unlock buttons at the same time for approximately five seconds.
Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, for signs of wear or damage. See When It Is Time for New Tires on page 6-68 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km).
Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 6-63 . Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 6-110 . { CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction type (radial and bias-belted tires) as your vehicle’s original tires.
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A Th.
Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis.
Used Replacement Wheels { CAUTION: Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 3-5 . { CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Removing the Spare Tire and Tools The jack and the wheel blocks are located under a cover near the passenger side rear seat. 1. Remove the jack cover by turning the two wing nuts one-quarter turn counterclockwise and pulling the jack cover off. A. Wheel Blocks B.
3. Remove the wheel blocks (A) attached to the jack (E) by turning the wing nut (C) counterclockwise. Place the wheel blocks where needed as indicated in previously in this section. The tools for changing a flat tire are located in the passenger’s side top-box storage unit.
2. To remove the spare tire lock, insert the ignition key, turn it clockwise and pull it straight out. 3. Assemble the two jack handle extensions (I) and wheel wrench (H) as shown. 4. Insert the open end of the extension (F) through the hole in the rear bumper (G) (hoist shaft access hole).
6. Use the wheel wrench hook that allows you to pull the hoist cable towards you, to assist in reaching the spare tire. 7. Tilt the tire with slack in the cable to access the tire/wheel retainer (D). Separate the retainer from the guide pin by sliding the retainer up the pin while pressing down on the latch.
Removing the Flat Tire and Installing the Spare Tire The tools that are needed include the jack (A), the wheel blocks (B), the jack handle (C), the jack handle extensions (D), and the wheel wrench (E). 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6-77 for more information.
3. Use the wheel wrench to loosen all the wheel nuts. Turn the wheel wrench counterclockwise to loosen the wheel nuts. Do not remove the wheel nuts yet. A. Front Position B. Rear Position { CAUTION: Getting under a vehicle when it is jacked up is dangerous.
Front Tire Flat: If the flat tire is on a front tire of the vehicle, you will need to use the jack handle (B) and only one jack handle extension (C). Attach the wheel wrench (D) to the jack handle extension (C). Attach the jack handle (B) to the jack (A).
5. Remove all the wheel nuts. 6. Take off the flat tire. { CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
8. Install the spare tire. { CAUTION: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash. 9. Put the wheel nuts back on with the rounded end of the nuts toward the wheel after mounting the spare tire.
12. Tighten the nuts firmly in a crisscross sequence as shown by turning the wheel wrench clockwise. When you reinstall the regular wheel and tire, you must also reinstall the center cap. Line the tab on the back of the tab with the slot in the wheel.
2. If it is visible, first try to tighten the cable by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot overtighten the cable. 3. Loosen the cable by turning the wrench counterclockwise three or four turns.
8. Attach the jack handle, extension, and wheel wrench to the jack and place it (with the wheel blocks) under the vehicle toward the front of the rear bumper. 9. Position the center lift point of the jack under the center of the spare tire. 10. Turn the wrench clockwise to raise the jack until it lifts the end fitting.
12. Lower the jack by turning the wheel wrench counterclockwise. Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable.
A. Spare Tire/Flat Tire (Valve Stem Pointed Down) B. Hoist Assembly C. Hoist Cable D. Tire/Wheel Retainer E. Hoist Shaft F. Hoist End of Extension Tool G.
2. Tilt the tire. Separate the tire/wheel retainer (D) from the guide pin. Pull the pin through the center of the wheel. Tilt the retainer down through the center wheel opening. 3. Assemble the two jack handle extensions (I) and wheel wrench (H) as shown.
5. Raise the tire part way upward. Make sure the retainer is fully seated across the underside of the wheel and is centered in the wheel opening. 6. Raise the tire fully against the underside of the vehicle by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice.
Have the damaged or flat road tire repaired or replaced as soon as you can and installed back onto your vehicle. This way, a spare tire will be available in case you need it again. Do not mix tires and wheels of different sizes, because they will not fit.
• Heavy pressure or aggressive rubbing with a cleaning cloth. Use of heavy pressure can damage the interior and does not improve the effectiveness of soil removal. • Laundry detergents or dishwashing soaps with degreasers can leave residue that streaks and attracts dirt.
Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather.
Care of Safety Belts Keep belts clean and dry. { CAUTION: Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection.
High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the vehicle. Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, chrome polish may be used on chrome or stainless steel trim, if necessary. Use special care with aluminum trim.
Aluminum or Chrome-Plated Wheels and Trim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel.
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty.
Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle.
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle’s warranty.
Instrument Panel Fuse Block The instrument panel fuse block access door is located on the driver side edge of the instrument panel. Pull off the cover to access the fuse block.
Fuses Usage 8 Passenger Side Turn Signal, Stoplamp 9 Passenger Door Module, Driver Unlock 10 Power Door Lock 2 (Unlock Feature) 11 Power Door Lock 2 (Lock Feature) 12 Stoplamps, Center-High Mounted St.
Center Instrument Panel Fuse Block The center instrument panel fuse block is located underneath the instrument panel, to the left of the steering column.
Underhood Fuse Block The underhood fuse block is located in the engine compartment, on the driver side of the vehicle. To access the fuse/relay block, push in on the tabs on the end of the fuse/relay block cover and lift. Notice: Spilling liquid on any electrical components on the vehicle may damage it.
Fuses Usage 6 Trailer Brake Controller 7 Front Washer 8 Oxygen Sensors 9 Antilock Brakes System 2 10 Trailer Back-up Lamps 11 Driver Side Low-Beam Headlamp 12 Engine Control Module (Battery) 13 Fuel I.
Fuses Usage 47 Not Used 48 Auxiliary Climate Control (Ignition) 49 Center High-Mounted Stoplamp (CHMSL) 50 Rear Defogger 51 Heated Mirror 52 SEO B1 Upfitter Usage (Battery) 53 Cigarette Lighter, Auxi.
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7-13 for more information.
Maintenance Schedule ..................................... .7-2 Introduction .................................................. .7-2 Maintenance Requirements ............................. .7-2 Your Vehicle and the Environment ................... .7-2 Using the Maintenance Schedule .
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements the vehicle warranties. See the Warranty and Owner Assistance booklet or your dealer/retailer for details.
Using the Maintenance Schedule We want to help keep this vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather.
Owner Checks and Services on page 7-9 tells what should be checked, when to check it, and what can easily be done to help keep the vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 7-13 and Maintenance Replacement Parts on page 7-15 .
❑ Inspect brake system. See footnote (a). ❑ Check engine coolant and windshield washer fluid levels and add fluid as needed. ❑ Perform any needed additional services. See “Additional Required Services” in this section. ❑ Inspect suspension and steering components.
Additional Required Services The following services should be performed at the first maintenance service after the indicated miles (kilometers) shown for each item.
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Inspect evaporative control system. An Emission Control Service. See footnotes † and (g).
(b) Visually inspect front and rear suspension and steering system for damaged, loose, or missing parts, signs of wear or lack of lubrication. Inspect power steering lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Visually check constant velocity joints, rubber boots, and axle seals for leaks.
(i) Drain, flush, and refill cooling system. This service can be complex; you should have your dealer/retailer perform this service. See Engine Coolant on page 6-26 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap, and filler neck.
Engine Coolant Level Check Check the engine coolant level and add DEX-COOL ® coolant mixture if necessary. See Engine Coolant on page 6-26 . Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer fluid reservoir and add the proper fluid if necessary.
Automatic Transmission Shift Lock Control System Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Parking Brake and Automatic Transmission P (Park) Mechanism Check { CAUTION: When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine Oil The engine requires a special engine oil meeting GM Standard GM4718M.
Usage Fluid/Lubricant Front Axle Propshaft Spline Spline Lubricant, Special Lubricant (GM Part No. U.S. 12345879, in Canada 10953511) or lubricant meeting requirements of GM 9985830. Hood Hinges Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Maintenance Replacement Parts Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 15908916 A3086C Oil Filter 89017524 PF48 Spark Plugs 12609877 41-985 Wiper Blades Front – 21.
Engine Drive Belt Routing 7-16.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 7-2 . Any additional information from Owner Checks and Services on page 7-9 can be added on the following record pages.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-18.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-19.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-20.
Customer Assistance and Information .............. .8-2 Customer Satisfaction Procedure ..................... .8-2 Online Owner Center ..................................... .8-4 Customer Assistance for Text Telephone (TTY) Users ......................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Cadillac. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments.
charge and your case will generally be heard within 40 days. If you do not agree with the decision given in your case, you may reject it and proceed with any other venue for relief available to you.
Online Owner Center Online Owner Center (U.S.) — www.gmownercenter.com/cadillac Information and services customized for your specific vehicle — all in one convenient place.
Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Cadillac has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Cadillac by dialing: 1-800-833-CMCC (2622).
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P. 11910, Mexico, D.
Roadside Service In the United States or Canada, call 1-800-882-1112 . Text Telephone (TTY), U.S. only, call 1-888-889-2438 . Service is available 24 hours a day, 365 days a year.
• Flat Tire Change: Service is provided to change a flat tire with spare tire. The spare tire, if equipped, must be in good condition and properly inflated. It is your responsibility for the repair or replacement of the tire if it is not covered by the warranty.
• Trip Interruption Benefits and Assistance: Pre-authorization, original detailed receipts, and a copy of the repair orders are required. Once authorization has been received, the Roadside Assistance advisor will help you make arrangements and explain how to receive payment.
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options.
General Motors reserves the right to unilaterally modify, change, or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described herein at its sole discretion.
Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are significant differences in the quality of coverage afforded by various insurance policy terms.
• Remove any valuables from your vehicle before it is towed away. Make sure this includes your insurance information and registration if you keep these items in your vehicle.
If another party’s insurance company is paying for the repairs, you are not obligated to accept a repair valuation based on that insurance company’s collision policy repair limits, as you have no contractual limits with that company.
Reporting Safety Defects to General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors. Call 1-800-458-8006, or write: Cadillac Customer Assistance Center Cadillac Motor Car Division P.O.
ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc. on the World Wide Web at: helminc.com Or you can write to: Helm, Incorporated P.O. Box 07130 Detroit, MI 48207 Prices are subject to change without notice and without incurring obligation.
This data can help provide a better understanding of the circumstances in which crashes and injuries occur. Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data (e.
✍ NOTES 8-18.
A Accessories and Modifications ............................ 6 - 3 Accessory Power Outlets ................................. 3-20 Adding Equipment to Y our Airbag-Equipped V ehicle ....................................................... 1-67 Additives, Fuel .
Audio System (cont.) Theft-Deterrent Feature ................................ 3-87 XM™ Satellite Radio Antenna System ............ 3-90 Automatic Headlamp System ............................ 3-17 Automatic T ransmission Fluid .......................
Child Restraints Child Restraint Systems ............................... 1-38 Infants and Y oung Children ........................... 1-34 Lower Anchors and T ethers for Children .......... 1-41 Older Children .........................................
Customer Assistance Information (cont.) Reporting Safety Defects to the United States Government ............................................ 8-14 Roadside Service .......................................... 8 - 7 Service Publications Ordering Information .
Electronic Immobilizer P ASS-Key ® III+ ........................................... 2-29 Electronic Immobilizer Operation P ASS-Key ® III+ ........................................... 2-29 Engine Air Cleaner/Filter ...................................
Fuel (cont.) Filling the T ank ............................................. 6 - 9 Fuels in Foreign Countries .............................. 6 - 9 G a g e ......................................................... 3-41 Gasoline Octane .................
I Ignition Positions ............................................. 2-31 Infants and Y oung Children, Restraints ............... 1-34 Inflation - T ire Pressure ................................... 6-60 Instrument Panel Brightness .....................
Locks Delayed Locking ........................................... 2 - 9 D o o r ........................................................... 2 - 9 Lockout Protection ....................................... 2-11 P o w e r D o o r .......................
O Odometer ...................................................... 3-29 Odometer , T rip ............................................... 3-29 Off-Road Driving ............................................. 5-12 Off-Road Recovery ........................
Power Assist Steps ......................................... 2-22 Privacy .......................................................... 8-16 Event Data Recorders .................................. 8-16 Navigation System ..................................
S Safety Belt Reminders ..................................... 3-29 Safety Belts C a r e o f ...................................................... 6-97 How to Wear Safety Belts Properly ................ 1-17 Lap-Shoulder Belt .........................
Storage Areas (cont.) Cupholders ................................................. 2-66 Glove Box .................................................. 2-66 Instrument Panel Storage Area ...................... 2-66 Luggage Carrier .......................
T ow/Haul Mode Light ....................................... 3-41 T owing Recreational V ehicle ..................................... 5-37 T owing a Trailer .......................................... 5-40 Y our V ehicle ...............................
Wheels Alignment and T ire Balance .......................... 6-74 Different Size .............................................. 6-71 Replacement ............................................... 6-74 Where to Put the Restraint .........................
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cadillac 2009 Escalade EXT è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cadillac 2009 Escalade EXT - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cadillac 2009 Escalade EXT imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cadillac 2009 Escalade EXT ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cadillac 2009 Escalade EXT, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cadillac 2009 Escalade EXT.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cadillac 2009 Escalade EXT. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cadillac 2009 Escalade EXT insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
