Manuale d’uso / di manutenzione del prodotto 2009 Escalade del fabbricante Cadillac
Vai alla pagina of 602
Seats and Restraint System ............................. 1 - 1 Head Restraints ......................................... 1 - 2 Front Seats ............................................... 1 - 3 Rear Seats .............................................. 1-10 Safety Belts .
Front Axle ............................................... 6-47 Headlamp Aiming ..................................... 6-48 Bulb Replacement .................................... 6-51 Windshield Wiper Blade Replacement ......... 6-54 Tires .............
GENERAL MOTORS, GM, the GM Emblem, CADILLAC, the CADILLAC Crest & Wreath, and the names ESCALADE and ESV are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. GM reserves the right to make changes after that time without notice.
Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this,” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning.
Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index.
✍ NOTES vi.
Head Restraints .............................................. .1-2 Front Seats ..................................................... .1-3 Power Seats ................................................. .1-3 P o w e r L u m b a r .......................
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. { CAUTION: With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash.
Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
• Raise or lower the rear part of the seat cushion by moving the rear of the control up or down. • Raise or lower the entire seat by moving the entire control up or down. The power reclining seatback control is located behind the power seat control on the outboard side of the seats.
Let go of the control when the lower seatback reaches the desired level of support. Your vehicle has a memory function which allows seat settings to be saved and recalled.
Heated and Cooled Seats If the front seats have the heated and cooled seat feature, the buttons used to control this feature are located on the climate control panel. { (Cooled Seat): To cool the entire seat, press the button with the cooled seat symbol.
Memory Features Your vehicle has the memory package. The controls for this feature are located on the driver’s door, and are used to program and recall memory settings for the driver’s seat, outside mirrors, steering wheel position, and the adjustable throttle and brake pedal feature, if your vehicle has it.
Easy Exit Seat The control for this feature is located on the driver’s door between buttons 1 and 2. With the vehicle in P (Park), the exit position can be recalled by pressing the exit button. You will hear a single beep. The driver’s seat will move back.
{ CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Center Seat Your vehicle may have a front center seat. The seatback doubles as an armrest and cupholder/storage area for the driver and passenger when the center seat is not used. Do not use it as a seating position when the seatback is folded down. Rear Seats Heated Seats The rear outboard seats have the heated seat feature.
60/40 Split Bench Seat (Second Row) If your vehicle has a 60/40 split bench, the seat(s) can be folded for additional cargo space or folded and tumbled for easy entry and exit to the third row seats, if your vehicle has them. These seats will have either the manual fold and tumble feature or the automatic seat release fold and tumble feature.
The seatback will fold forward automatically. Leaving the seatback in this position creates a flat load floor. If the seatback cannot fold flat, try moving the front seat forward and/or put the front seatback in the upright position. 3. Lift the same lever again to release the rear of the seat from the floor.
Returning the Seat(s) to the Sitting Position To return the seat to the sitting position, do the following: 1. Pull the seat down until it latches to the floor. The seatback cannot be raised if the seat is not latched to the floor. { CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash.
Folding and Tumbling the Seat(s) from the Third Row Seats { CAUTION: Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position.
Power Release Fold and Tumble Feature The transmission must be in (P) Park for this feature to work. Folding and Tumbling the Seat(s) { CAUTION: Automatically folding and tumbling the seat when someone is sitting in the seat, could cause injury to the person sitting there.
Returning the Seat(s) to the Sitting Position To return the seat to the sitting position, do the following: 1. Pull the seat down until it latches to the floor. The seatback cannot be raised if the seat is not latched to the floor. { CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash.
Folding and Tumbling the Second Row Seat(s) from the Third Row Seats or Outside { CAUTION: Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position.
Reclining Seatbacks To recline the seatback, do the following: 1. Lift the lever located on the outboard side of the seat. 2. Move the seatback to the desired position, then release the lever to lock the seatback in place. 3. Push and pull on the seatback to make sure it is locked.
Manual Fold and Tumble Feature Folding and Tumbling the Seat(s) To fold and tumble the seat, do the following: 1. Make sure that there is nothing under, in front of, or on the seat. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts.
3. Lift the lever again to release the rear of the seat from the floor. The seat will tumble forward. Returning the Seat(s) to the Sitting Position To return the seat to the sitting position, do the following: 1. Pull the seat down until it latches to the floor.
Folding and Tumbling the Seat(s) from the Third Row Seats { CAUTION: Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position.
Power Release Fold and Tumble Feature The transmission must be in (P) Park for this feature to work. Folding and Tumbling the Seat(s) { CAUTION: Automatically folding and tumbling the seat when someone is sitting in the seat, could cause injury to the person sitting there.
Returning the Seat(s) to the Sitting Position To return the seat to the sitting position, do the following: 1. Pull the seat down until it latches to the floor. The seatback cannot be raised if the seat is not latched to the floor. { CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash.
Folding and Tumbling the Second Row Seat(s) from the Third Row Seats or Outside { CAUTION: Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position.
Third Row Seat If the vehicle has a third row seat, the seatback(s) can be folded and the entire seat can be tumbled, or removed from the vehicle. Folding the Seatback(s) To fold the seatback, do the following: 1. Open the liftgate to access the controls for the seat.
Unfolding the Seatback(s) To return the seatback to the upright position, do the following: 1. Open the liftgate to access the controls for the seat. 2. Pull up on the seatback until it locks into the upright position. { CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash.
6. Tilt the seat fully forward to lock it into place. 7. Push and pull on the seat to make sure it is locked. Put the seat in this position only when necessary for additional cargo space. Returning the Third Row Seat from a Tumbled Position To return the seat to the normal seating position, do the following: 1.
Removing the Third Row Seat To remove the seat, do the following: 1. Open the liftgate to access the controls for the seat. 2. Fold the seatback forward using the instructions listed under “Folding the Seatbacks” previously. The seat cannot be removed unless the seatback is folded.
{ CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 6. Push and pull on the seatback to make sure it is locked.
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. { CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
After more than 40 years of safety belts in vehicles, the facts are clear. In most crashes buckling up does matter... a lot! Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Take the simplest vehicle. Suppose it is just a seat on wheels.
Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield.
or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces.
Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 1-52 or Infants and Young Children on page 1-55 .
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Q: What is wrong with this? A: The belt is behind the body. { CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Q: What is wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt except for the center front passenger position, if equipped, which has a lap belt. See Lap Belt on page 1-50 for more information. The lap-shoulder belts for the first and second row seating positions are equipped with free-falling latch plates.
Engaging the child restraint locking feature in the right front seating position may affect the passenger sensing system. See Passenger Sensing System on page 1-87 for more information.
5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling off the shoulder.
Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed on a shoulder belt, the comfort guide positions the belt away from the neck and head.
2. Place the guide over the belt, and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat.
{ CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
To make the belt shorter, pull its free end as shown until the belt is snug. If the belt is not long enough, see Safety Belt Extender on page 1-51 . Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if necessary.
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster.
Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs.
{ CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints.
{ CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 110 kg (240 lb) force on a person’s arms.
{ CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types.
{ CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. Securing an Add-On Child Restraint in the Vehicle { CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer.
A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
{ CAUTION: A child in a child restraint in the center front seat can be badly injured or killed by the frontal airbags if they inflate. Never secure a child restraint in the center front seat. It is always better to secure a child restraint in a rear seat.
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Some child restraints with top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
For models with a three passenger third row seat, see the information following for installing a child restraint with a top tether in the third row, if your vehicle has one.
For models with 60/40 second row seating, the top tether anchors are located at the bottom rear of the seat cushion for each seating position in the second row. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. See Where to Put the Restraint on page 1-61 for additional information.
Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not fold the empty rear seat with a safety belt buckled.
If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback. If the position you are using has an adjustable headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint.
Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle.
The vehicle’s lap-shoulder belts for the first and second row seating positions are equipped with free-falling latch plates. If the vehicle has a third row, the lap-shoulder belts have either free-falling or cinching latch plates. Use the following pictures to determine the latch plate style: 1.
For third row seating positions, with cinching latch plates, tilt the latch plate to adjust the belt if needed. 3. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.
4. For passenger seating positions with a lap-shoulder belt and a free-falling latch plate, pull the rest of the shoulder belt all the way out of the retractor to set the lock. When installing a child restraint using a lap-shoulder belt and a cinching latch plate, skip Step 4 and proceed to Step 5.
6. If the child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-63 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure.
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint.
If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-63 for how and where to install the child restraint using LATCH. If a child restraint is secured using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH) on page 1-63 for top tether anchor locations.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
If the airbag is off, the of f indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the on indicator is lit, see “If the On Indicator is Lit for a Child Restraint” under Passenger Sensing System on page 1-87 for more information.
Here are the most important things to know about the airbag system: { CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
{ CAUTION: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows.
If your vehicle has roof-rail airbags and a third row passenger seat, the airbags are located in the ceiling above the rear windows for the outboard passenger positions in the third row.
When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inflate if the impact exceeds a predetermined deployment threshold.
Roof-rail airbags are not intended to inflate in rear impacts. Both roof-rail airbags will deploy when either side of the vehicle is struck, or if the sensing system predicts that the vehicle is about to roll over, or in a severe frontal impact.
What Will You See After an Airbag Inflates? After the frontal airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy.
In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system.
The passenger sensing system works with sensors that are part of the right front passenger seat and safety belt. The sensors are designed to detect the presence of a properly-seated occupant and determine if the right front passenger frontal airbag should be enabled (may inflate) or not.
The passenger sensing system is designed to turn off the right front passenger frontal airbag if: • The right front passenger seat is unoccupied. • The system determines an infant is present in a child restraint. • A right front passenger takes his/her weight off of the seat for a period of time.
If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
If the Of f Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat.
Additional Factors Af fecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status.
Servicing Your Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Your dealer/retailer and the service manual have information about servicing the vehicle and the airbag system.
Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Replacing Restraint System Parts After a Crash { CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash.
Keys .............................................................. .2-3 Remote Keyless Entry (RKE) System ............... .2-4 Remote Keyless Entry (RKE) System Operation .................................................. .2-5 Remote Vehicle Start ..
Object Detection Systems .............................. .2-42 Ultrasonic Rear Parking Assist (URPA) ........... .2-42 Side Blind Zone Alert (SBZA) ........................ .2-44 Rear Vision Camera (RVC) ........................... .2-48 OnStar ® System .
Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed.
Remote Keyless Entry (RKE) System The Remote Keyless Entry (RKE) system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-4 .
Pressing K on the RKE transmitter disarms the content theft-deterrent system. See Content Theft-Deterrent on page 2-21 . / (Remote Vehicle Start): For vehicles with this feature, press / to start the engine from outside the vehicle using the RKE transmitter.
Battery Replacement Replace the battery if the REPLACE BATTERY IN REMOTE KEY message displays in the DIC. See “REPLACE BATTERY IN REMOTE KEY” under DIC Warnings and Messages on page 3-56 for additional information. Notice: When replacing the battery, do not touch any of the circuitry on the transmitter.
Remote Vehicle Start This feature allows you to start the engine from outside of the vehicle. It may also start up the vehicle’s heating or air conditioning systems and rear window defogger. Normal operation of the system will return after the key is turned to the ON/RUN position.
3. If it is the first remote start since the vehicle has been driven, repeat these steps, while the engine is still running, to extend the engine running time by 10 minutes. Remote start can be extended one time. After entering the vehicle during a remote start, insert and turn the key to ON/RUN to drive the vehicle.
Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Programmable Automatic Door Locks Vehicles with an automatic lock/unlock feature enable you to program the vehicle’s power door locks. You can program this feature through the Driver Information Center (DIC). See DIC Vehicle Customization on page 3-65 for more information on DIC programming.
Lockout Protection This feature protects you from locking the key in the vehicle when the key is in the ignition and a front door is open. If the driver’s side power door lock switch is pressed when the driver’s door is open and the key is in the ignition, all of the doors will lock and then the driver’s door will unlock.
See Power Liftgate on page 2-14 for more information on how to use the power liftgate. To unlock the liftgate, use the power door lock switch or press the door unlock button on the Remote Keyless Entry (RKE) transmitter twice. See Remote Keyless Entry (RKE) System Operation on page 2-5 .
Power Liftgate Power Liftgate Operation { CAUTION: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
The power liftgate can be power opened and closed in the following ways: • Press and hold the power liftgate button on the Remote Keyless Entry (RKE) transmitter until the liftgate starts moving. Remote Keyless Entry (RKE) System Operation on page 2-5 for more information.
Manual Operation of Power Liftgate To change the liftgate to manual operation, press the switch on the overhead console to the OFF position. With the power liftgate disabled and all of the doors unlocked, the liftgate can be manually opened and closed.
Windows { CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows { CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed.
Express-Down/Up Windows Windows with the express feature allow the windows to be raised and lowered all the way without holding the switch. Press or pull the switch fully and release it to activate the express feature. The express mode can be canceled at any time by briefly pressing or pulling the switch.
Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or is not working, you will need to reprogram each front power window for the express-up feature to work. Before reprogramming, replace or recharge the vehicle’s battery.
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Content Theft-Deterrent Your vehicle has a content theft-deterrent alarm system.
Testing the Alarm To test the alarm: 1. From inside the vehicle, lower the driver’s window and open the driver’s door. 2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the RKE transmitter.
PASS-Key ® III+ Electronic Immobilizer Operation Your vehicle has PASS-Key ® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key ® III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition.
See your dealer/retailer or a locksmith who can service PASS-Key ® III+ to get a new key blank that is cut exactly as the ignition key that operates the system. To program the new additional key: 1. Verify that the new key has a 1 stamped on it. 2. Insert the original, already programmed, key in the ignition and start the engine.
Ignition Positions The ignition switch has four different positions. To shift out of P (Park), the ignition must be in ON/RUN or ACC/ACCESSORY and the regular brake pedal must be applied. A (LOCK/OFF): This position locks the ignition. It may also lock the steering wheel and automatic transmission.
Retained Accessory Power (RAP) The following vehicle accessories can be used for up to 10 minutes after the engine is turned off: • Audio System • Power Windows • OnStar ® System (if equipped) • Sunroof (if equipped) These features work when the key is in ON/RUN or ACC/ACCESSORY.
2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or − 18°C), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds.
Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F ( − 18°C). Vehicles with an engine heater should be plugged in at least four hours before starting.
Automatic Transmission Operation If the vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. The vehicle has a Hydra-Matic ® 6L80 automatic transmission, and has an electronic shift position indicator within the instrument panel cluster.
R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.
M (Manual Mode): This position lets drivers select the range of gears appropriate for current driving conditions. See Driver Shift Control (DSC) later in this section. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission.
Driver Shift Control (DSC) The vehicle has Driver Shift Control (DSC). DSC controls the vehicle’s transmission and vehicle speed while driving down hill or towing a trailer by allowing you to select a desired range of gears. To use this feature, do the following: 1.
Tow/Haul Mode The vehicle has a tow/haul mode. The tow/haul mode adjusts the transmission shift pattern to reduce shift cycling, providing increased performance, vehicle control, and transmission cooling when towing or hauling heavy loads. Press the button located on the end of the shift lever to turn the tow/haul on or off.
Cruise Grade Braking Cruise Grade Braking assists when driving on a downhill grade. It maintains vehicle speed by automatically implementing a shift schedule that uses the engine and the transmission to slow the vehicle.
If the ignition is on when the parking brake is released, the brake system warning light goes off. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving.
Shifting Into Park { CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured.
Torque Lock If you are parking on a hill and you do not shift the transmission into P (Park) properly, the weight of the vehicle can put too much force on the parking pawl in the transmission. It might be diff icult to pull the shift lever out of P (Park).
Parking Over Things That Burn { CAUTION: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use.
Resetting the Power Foldaway Mirrors Reset the power foldaway mirrors if: • The mirrors are accidentally obstructed while folding. • They are accidentally manually folded/unfolded. • The mirrors will not stay in the unfolded position. • The mirrors vibrate at normal driving speeds.
Outside Heated Mirrors < (Rear Window Defogger): Press to heat the mirrors. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-27 for more information.
The display is located near the passenger side rear window and can be seen by looking over your right shoulder. URPA uses three color-coded lights to provide distance and system information. How the System Works URPA comes on automatically when the shift lever is moved into R (Reverse).
When the System Does Not Seem to Work Properly If the URPA system will not activate due to a temporary condition, the message PARK ASSIST OFF will be displayed on the DIC and a red light will be shown on the rear URPA display when the shift lever is moved into R (Reverse).
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. { CAUTION: SBZA is only a lane changing aid and does not replace driver vision.
How the System Works When the vehicle is started, both outside mirror displays will briefly come on to indicate that the system is operating. When the vehicle is moving forward, the left or right side mirror SBZA display will light up if a vehicle is detected in that blind zone.
SBZA does not operate when the left or right corners of the rear bumper are covered with mud, dirt, snow, ice, slush, or in heavy rainstorms. For cleaning instructions, see Washing Your Vehicle on page 6-100 . If the DIC still displays the SIDE BLIND ZONE SYSTEM UNAVAILABLE message after cleaning the bumper, see your dealer/retailer.
Rear Vision Camera (RVC) This vehicle may have a Rear Vision Camera system. Read this entire section before using it. The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle.
Adjusting the Brightness and Contrast of the Screen To adjust the brightness and contrast of the screen, press the CONFIG hard key while the rear vision camera image is on the display. Any adjustments made will only affect the rear vision camera screen.
Rear Vision Camera System Unavailable: Displays when the system is not receiving information it requires from other vehicle systems. If any other problem occurs or if a problem persists, see your dealer/retailer. { CAUTION: The Rear Vision Camera (RVC) system does not replace driver vision.
When the System Does Not Seem To Work Properly The rear vision camera system might not work properly or display a clear image if: • The RVC is turned off. See “Turning the Rear Camera System On or Off” earlier in this section. • It is dark. • The sun or the beam of headlights is shining directly into the camera lens.
OnStar ® System OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, information, and convenience services. If the airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location.
OnStar Services Available with the Safe & Sound Plan • Automatic Notification of Airbag Deployment • Advanced Automatic Crash Notification (AACN) (If equipped) • Link to Emergency Services.
OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses minutes to access location-based weather, local traff ic reports, and stock quotes. Press the phone button and give a few simple voice commands to browse through the various topics.
Your Responsibility Increase the volume of the radio if the OnStar advisor cannot be heard. If the light next to the OnStar buttons is red, the system may not be functioning properly.
This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use this system with any garage door opener that does not have the stop and reverse feature.
2. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button.
To program up to three devices: 1. To verify that the garage door opener is a Fixed Code unit, remove the battery cover on the hand held transmitter supplied by the manufacturer of the garage door opener motor. If there are a row of dip switches similar to the graphic above, the garage door opener is a Fixed Code unit.
The panel of switches might not appear exactly as they do in the examples above, but they should be similar. The switch positions on the hand-held transmitter could be labeled, as follows: • A switch in the up position could be labeled as “Up,” “+,” or “On.
4. The indicator lights will blink slowly. Enter each switch setting from Step 2 into your vehicle’s Universal Home Remote. You will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows: • If you wrote “Left,” press the left button in the vehicle.
Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted. Reprogramming Universal Home Remote Buttons Any of the three buttons can be reprogrammed by repeating the instructions.
Storage Areas Glove Box Pull the bottom of the glove box handle upward to open it. Use the key to lock and unlock the glove box. Cupholders Cupholders are located in the center console for the front passengers. Press down on the access door release to open and use the front cupholders.
Rear Passenger Cupholders Pull down on the lid to access the cupholders in the rear floor console. Vehicles with the rear seat armrest may also contain cupholders. Pull down the armrest to use the cupholders. Center Console Storage A console compartment is located between the bucket seats.
Luggage Carrier For vehicles with a luggage carrier, items can be loaded on top of the vehicle. The luggage carrier has siderails attached to the roof and crossrails, if equipped, which can be moved back and forth to help secure cargo.
Rear Storage Area For vehicles with a rear storage area, it is located in the rear cargo area of the vehicle on the driver’s side trim panel. Turn the knobs and swing the storage door to access the storage compartment.
Express-Open/Express-Close: To express-open the sunroof, fully press and release the rear of the driver’s side switch. The sunroof will open automatically. To stop the sunroof partway, press the switch a second time. To express-close the sunroof, fully press and release the front of the driver’s side switch.
Instrument Panel Overview .............................. .3-4 Hazard Warning Flashers ............................... .3-6 H o r n ............................................................ .3-6 Tilt Wheel ...........................................
Security Light .............................................. .3-45 Fog Lamp Light ........................................... .3-45 Lights On Reminder ..................................... .3-45 Cruise Control Light ..................................
✍ NOTES 3-3.
Instrument Panel Overview United States version shown; Canada similar. 3-4.
The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-31 . B. Turn Signal/Multifunction Lever on page 3-7 . C. Instrument Panel Cluster on page 3-34 . D. Hazard Warning Flashers on page 3-6 . E. Shift Lever and Range Selection Mode.
Hazard Warning Flashers | (Hazard Warning Flasher): Press this button located on top of the steering column, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off.
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: G : Turn and Lane Change Signals 5 : Headlamp High/Low-Beam Changer N : Windshield Wipers L : Windshield Washer 5 : Rear Wiper Delay Z : Rear Wiper = : Rear Wiper Wash Flash-to-Pass Feature.
Turn and Lane-Change Signals An arrow on the instrument panel cluster flashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever for less than one second until the arrow starts to flash to signal a lane change.
Flash-to-Pass This feature lets you use the high-beam headlamps to signal a driver in front of you that you want to pass. It works even if the headlamps are in the automatic position.
Rainsense™ II Wipers The vehicle has Rainsense™ II windshield wipers. These wipers automatically turn on when a sensor, mounted next to the inside rearview mirror, detects moisture on the windshield. When active, these wipers are able to detect moisture on the windshield and automatically turn on the wipers.
Windshield Washer { CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. L (Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever.
Rear Window Wiper/Washer { CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. The rear wiper control is located on the turn signal/multifunction lever.
Cruise Control { CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use the cruise control on winding roads or in heavy traff ic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control.
The cruise control buttons are located on left side of the steering wheel. T (On/Off): Turns the system on or of f. The indicator light is on when cruise control is on and turns off when cruise control is off. + RES (Resume/Accelerate): Press to make the vehicle accelerate or resume to a previously set speed.
Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, this shuts off the cruise control. But it does not need to be reset. Once the vehicle speed reaches about 25 mph (40 km/h) or more, press the +RES button on the steering wheel.
Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed.
The exterior lamps control has four positions: 9 (Off): Turns of f the automatic headlamps and daytime running lamps (DRL). Turning the headlamp control to the off position again will turn the automatic headlamps or DRL back on. For vehicles first sold in Canada, the off position only works when the vehicle is shifted into the P (Park) position.
IntelliBeam ® Intelligent High-Beam Headlamp Control System For vehicles with this feature, be sure to read this entire section before using it. IntelliBeam ® is an enhancement to the vehicle’s headlamp system.
• The exterior lamp control is turned to any setting except AUTO. When this occurs, IntelliBeam ® will be disabled until the control is turned back to the AUTO position.
Disabling and Resetting IntelliBeam ® at the Rearview Mirror IntelliBeam ® can be disabled by using the controls on the inside rearview mirror. AUTO 3 (On/Off): To disable the system, press this button on the inside rearview mirror.
Headlamps on Reminder If a door is open, a reminder chime will sound when the headlamps or parking lamps are manually turned on and the key is out of the ignition. To turn off the chime, turn the headlamp switch to off or AUTO and then back on, or close and re-open the door.
There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system.
Instrument Panel Brightness D (Instrument Panel Brightness): This feature controls the brightness of the instrument panel lights and is located next to the exterior lamp control. Push the knob to extend out and then it can be turned. Turn the knob clockwise or counterclockwise to brighten or dim the instrument panel lights.
Reading Lamps If the vehicle has reading lamps, press the button located next to the lamp to turn it on or off. The vehicle may also have reading lamps in other locations. The lamps cannot be adjusted. Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge.
Battery Run-Down Protection This feature shuts off the dome lamps if they are left on for more than 10 minutes when the ignition is in LOCK/OFF. This helps to prevent the battery from running down. Accessory Power Outlet(s) The accessory power outlets let you plug in auxiliary electrical equipment, such as a cellular telephone.
Ashtray(s) and Cigarette Lighter The front ashtray and cigarette lighter are located in the center console near the cupholders, if the vehicle has them.
Climate Controls Dual Automatic Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. The vehicle also has a flow-through ventilation system described later in this section. A. Driver and Passenger Temperature Controls B.
Automatic Operation AUTO (Automatic): When automatic operation is active the system will control the inside temperature, the air delivery, and the fan speed.
Manual Operation y9 z (Fan Control): Press the up or down arrows to increase or decrease the fan speed Pressing this button when the system is off will turn the system on. Pressing either arrow while using automatic operation will place the fan in manual operation.
# (Air Conditioning): Press to turn the air conditioning (A/C) compressor on and off. An indicator light comes on to show that the air conditioning is on.
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. < (Rear Window Defogger): Press to turn the rear window defogger on or off. It automatically turns of f after it has been activated. The defogger can also be turned off by turning off the engine.
Rear Air Conditioning and Heating System and Electronic Climate Controls For vehicles with the rear heat and air conditioning controls, they are integrated with the rear seat audio controls located in the center console. The system can be controlled from the front controls as well as the rear controls.
Automatic Operation, If Equipped. AUTO: Press the air delivery mode button until this setting is selected to control the inside temperature, air delivery, and fan speed. AUTO appears in the display when automatic operation is active. +/ − (Increase/Decrease Temperature): Press the + or − buttons to increase or decrease the cabin temperature.
Instrument Panel Cluster The instrument panel cluster is designed to let show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel the vehicle has and many other things needed to drive safely and economically. United States version shown, Canada similar.
Speedometer and Odometer The speedometer shows the vehicle’s speed in both miles per hour (mph) and kilometers per hour (km/h). The vehicle’s odometer works together with the Driver Information Center (DIC). The Trip odometer can be set. See “Trip Odometer” under DIC Operation and Displays on page 3-48 for more information.
Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime sounds for several seconds to remind the front passenger to buckle their safety belt. This only occurs if the passenger airbag is enabled. See Passenger Sensing System on page 1-87 for more information.
{ CAUTION: If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash.
If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag.
Brake System Warning Light With the ignition on, the brake system warning light comes on when the parking brake is set. If the vehicle is driven with the parking brake engaged, a chime sounds when the vehicle speed is greater than 3 mph (5 km/h). The vehicle’s hydraulic brake system is divided into two parts.
Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off.
Engine Coolant Temperature Gage This gage shows the engine coolant temperature. If the indicator on the gage moves towards the shaded area on the thermostat, it means that the engine coolant has overheated.
When the Light Flashes First and Then is On Steady This indicates that there could be a problem with the Tire Pressure Monitor System. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle.
This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required.
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration.
This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. If the light comes on and stays on, it means that oil is not flowing through the engine properly.
Cruise Control Light The cruise control light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 3-13 for more information. Highbeam On Light This light comes on when the high-beam headlamps are in use.
The gage will first indicate empty before the vehicle is out of fuel, but the vehicle’s fuel tank should be filled soon. Here are some situations owners may experience with the fuel gage. None of these indicate a problem with the fuel gage. • At the gas station, the fuel pump shuts off before the gage reads full.
DIC Operation and Displays The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel, next to the steering wheel. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected.
Trip/Fuel Menu Items 3 (Trip/Fuel): Press this button to scroll through the following menu items: Odometer Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km).
Average Economy Press the trip/fuel button until AVERAGE ECONOMY displays. This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this menu item was reset.
Vehicle Information Menu Items T (Vehicle Information): Press this button to scroll through the following menu items: Oil Life Press the vehicle information button until OIL LIFE REMAINING displays. This display shows an estimate of the oil’s remaining useful life.
Tire Pressure On vehicles with the Tire Pressure Monitor System (TPMS), the pressure for each tire can be viewed in the DIC. The tire pressure will be shown in either pounds per square inch (psi) or kilopascals (kPa). Press the vehicle information button until the DIC displays FRONT TIRES PSI (kPa) LEFT ## RIGHT ##.
Relearn Remote Key This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. To match an RKE transmitter to your vehicle: 1. Press the vehicle information button until PRESS V TO RELEARN REMOTE KEY displays. 2. Press the set/reset button until REMOTE KEY LEARNING ACTIVE is displayed.
Compass Zone The zone is set to zone eight upon leaving the factory. Your dealer/retailer will set the correct zone for your location. Under certain circumstances, such as during a long distance cross.
Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. It is suggested to calibrate away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible.
DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition.
ENGINE HOT A/C (Air Conditioning) TURNED OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gage on page 3-41 . To avoid added strain on a hot engine, the air conditioning compressor automatically turns off.
ENGINE POWER IS REDUCED This message displays and a chime sounds when the cooling system temperature gets too hot and the engine further enters the engine coolant protection mode. See Engine Overheating on page 6-30 for further information. This message also displays when the vehicle’s engine power is reduced.
OIL PRESSURE LOW STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the Driver Information Center (DIC), stop the vehicle as soon as possible. Do not drive the vehicle until the cause of the low oil pressure is corrected.
REPLACE BATTERY IN REMOTE KEY This message displays if a Remote Keyless Entry (RKE) transmitter battery is low. The battery needs to be replaced in the transmitter. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-5 .
SERVICE BRAKES SOON This message displays if there is a problem with the brake system. If this message appears, stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display. If the message is still displayed or appears again when you begin driving, the brake system needs service.
SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system. The vehicle may or may not restart so you may want to take the vehicle to your dealer/retailer before turning off the engine. See PASS-Key ® III+ Electronic Immobilizer Operation on page 2-23 for more information.
STABILITRAK OFF If your vehicle has StabiliTrak, this message displays when you turn off StabiliTrak, or when the stability control has been automatically disabled. To limit wheel spin and realize the full benefits of the stability enhancement system, you should normally leave StabiliTrak on.
TIRE LEARNING ACTIVE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the TPMS is re-learning the tire positions on your vehicle. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor.
DIC Vehicle Customization Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers.
DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature.
AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Programmable Automatic Door Locks on page 2-11 for more information.
To select a setting, press the set/reset button while the desired setting is displayed on the DIC. REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter.
EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the customization button until EXIT LIGHTING appears on the DIC display.
AUTO HIGH BEAMS If your vehicle has this feature, it allows you to select to have the Intellibeam ® system turned off or on. See Exterior Lamps on page 3-16 for more information. Press the customization button until AUTO HIGH BEAMS appears on the DIC display.
PARK TILT MIRRORS This feature allows you to select whether or not the outside mirror(s) will automatically tilt down when the vehicle is shifted into R (Reverse). See Outside Power Foldaway Mirrors on page 2-40 for more information. Press the customization button until PARK TILT MIRRORS appears on the DIC display.
To select a setting, press the set/reset button while the desired setting is displayed on the DIC. EASY EXIT SETUP If your vehicle has this feature, it allows you to select which areas will recall with the automatic easy exit seat feature. It also allows you to turn off the automatic easy exit feature.
REMOTE START If your vehicle has this feature, it allows you to turn the remote start off or on. The remote start feature allows you to start the engine from outside of the vehicle using the Remote Keyless Entry (RKE) transmitter. See Remote Vehicle Start on page 2-8 for more information.
FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Voice Recognition The Bluetooth system uses voice recognition to interpret voice commands to dial phone numbers and name tags. Noise: Keep interior noise levels to a minimum. The system may not recognize voice commands if there is too much background noise.
Pairing Information: • Up to five cell phones can be paired to the in-vehicle Bluetooth system. • The pairing process is disabled when the vehicle is moving. • The in-vehicle Bluetooth system automatically links with the first available paired cell phone in the order the phone was paired.
Deleting a Paired Phone 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Delete”. The system asks which phone to delete followed by a tone.
Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”. The system responds with “Store, number please” followed by a tone.
3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. • If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number.
Using the Delete Command The delete command allows specific name tags to be deleted. To use the delete command: 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Delete”. The system responds with “Delete, please say the name tag” followed by a tone.
Using the Dial Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Dial using <phone name>”. “Number please” followed by a tone. 3. Say the entire number without pausing.
Using the Call Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Call”. The system responds with “Call using <phone name>. Please say the name tag” followed by a tone. 3. Say the name tag of the person to call.
Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. • Press b g to answer an incoming call when another call is active. The original call is placed on hold. • Press b g again to return to the original call.
Transferring a Call Audio can be transferred between the in-vehicle Bluetooth system and the cell phone. To Transfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press b g . The system responds with “Ready” followed by a tone.
Sending a Number During a Call 1. Press b g . The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Say a number to send tones” followed by a tone.
Clearing the System Unless information is deleted out of the in-vehicle Bluetooth system, it will be retained indefinitely. This includes all saved name tags in the phonebook and phone pairing information. For information on how to delete this information, see the above sections on Deleting a Paired Phone and Deleting Name Tags.
Driver Control of the Audio System The driver has basic control of the whole audio system. Press and hold O for more than two seconds to turn off the radio, RSE, and the RSA (rear seat audio). See Navigation Audio System on page 4-62 for more information.
Push the power button to turn on the headphones. An indicator light located on the headphones comes on. If the light comes on but, there is intermittent sound and/or static on the headphones, or if the indicator light does not come on, the batteries might need to be replaced.
Audio/Video (A/V) Jacks The A/V jacks are located on the rear of the floor console. The A/V jacks allow audio or video signals to be connected from an auxiliary device such as a camcorder or a video game unit to the RSE system. Adapter connectors or cables (not included) may be required to connect the auxiliary device to the A/V jacks.
Audio Output Audio from the DVD player or auxiliary inputs can be heard through the following possible sources: • Wireless Headphones • Vehicle Speakers • Vehicle wired headphone jacks on the rear seat audio system, if the vehicle has this feature.
Remote Control To use the remote control, aim it at the transmitter window at the rear of the overhead console and press the desired button. Direct sunlight or very bright light can affect the ability of the RSE transmitter to receive signals from the remote control.
y (Main Menu): Press to access the DVD menu. The DVD menu is different on every DVD. Use the navigation arrows to move the cursor around the DVD menu. After making a selection press the enter button. This button only operates when using a DVD. Q , R , q , r (Menu Navigation Arrows): Use the arrow buttons to navigate through a menu.
r (Fast Reverse): Press to fast reverse the DVD or CD. To stop fast reversing a DVD video, press the play/pause button. To stop fast reversing a DVD audio or CD, release the fast reverse button. This button might not work when the DVD is playing the copyright information or the previews.
(Clear): Press within three seconds after entering a numeric selection, to clear all numeric inputs. } 10 (Double Digit Entries): Press to select chapter or track numbers greater than 9. Press this button before entering the number. Battery Replacement To change the remote control batteries: 1.
Problem Recommended Action The auxiliary source is running but there is no picture or sound. Check that the RSE video screen is in the auxiliary source mode. Check the auxiliary input connections at both devices. Sometimes the wireless headphone audio cuts out or buzzes.
Cleaning the RSE Overhead Console When cleaning the RSE overhead console surface, use only a clean cloth dampened with clean water. Cleaning the Video Screen When cleaning the video screen, use only a clean cloth dampened with clean water. Use care when directly touching or cleaning the screen, as damage can result.
Using the RSE System DVD Player: The loading slot for the DVD player is located at the top of the head restraint. Insert the disc partially into the loading slot with the printed side facing the rear of the vehicle. The DVD player automatically draws the disc in, “Loading” displays on the screen along with a disc indicator, and playback starts.
POWER O : Press to turn the power on or off. Each video screen can be powered on or off independently. EJECT X : Press to eject a disc from the DVD slot. If a disc is ejected from the player, but not removed, it will automatically reload into the player.
Headphone Jack: Wired headphones can be plugged into the headphone jack with one-eighth inch stereo plugs. AV INPUT: (Audio/Video Input Jack): The audio/video input jack is located below the video display screen and allows viewing of auxiliary sources such as portable DVD players, game stations, or video cameras, on each screen.
Wireless Headphones The two wireless headphones included with the Headrest DVD RSE system will only work with the Headrest DVD RSE system and are marked for channel 3 and 4. The wireless headphones must be used within a line of sight of the transmitter that is located above the video display screen.
Remote Control Buttons POWER: Press to turn the Headrest DVD RSE system on and off. SOURCE: Press to select between Monitor 3, Monitor 4, or AV INPUT. Any video equipment connected to the AV inputs automatically overrides the source selection.
SOUND AROUND ON/OFF: Press to turn the FM Transmitter power on or off. MUTE > (For DVD Only): Press to turn off the headphone sound. Press again to turn the sound on again. PIX (Picture Selection): Press to adjust the picture’s On Screen Display (OSD).
TITLE: Press to enter the disc title mode. The title feature is disc-specific, and may not be available on all discs. SUBTITLE: Press to change the subtitle language to another available language or to turn subtitles off. ANGLE: Press to select a different viewing angle for discs that are recorded with different camera angles.
PREV g (Previous): Press to play the previous chapter or track. To return to previous chapters or tracks one at a time, press and release multiple times until the desired chapter or track is reached.
To set the language for the OSD: 1. Press the SETUP button on the remote control. 2. Use the left/right navigation arrows to navigate the General Setup Page, then use the down navigation arrow to select the OSD language. 3. Press the right navigation arrow and then use the up/down navigation arrows to select English, French, or Spanish.
To reset all options to factory defaults: 1. Press the SETUP button on the remote control. 2. Use the left/right and down navigation arrows on the remote control to select the Default sub-menu under the Preference Page. 3. Press the right navigation arrow, then press ENTER to reset.
Settings for Parental Control Use the SETUP MENU to access the parental control feature. It allows for control of the type of movie rating content (from G to Adult) that can be viewed and is only accessible when no disc is loaded. To setup the Parental Control: 1.
To create a six digit password, use the numeric keypad on the remote control. Press the ENTER button to confirm. The default password is 136900. To change the Parental Control Password: 1. Press the SETUP button on the remote control 2. Navigate to the Password sub-menu under the Password Setup Page.
Playing Audio CD When an audio CD is playing, the display shows the current track and the amount of time that track has been playing, the total amount of time on the disc, and the current time running on the disc. DISPLAY: Press to choose from the following display options: 1.
1. Press STOP if a disc is playing. Press the up or down navigation arrows on the remote control to go through the folder list on the left side of the screen. 2. Press ENTER when the desired folder is highlighted. 3. Press the up or down navigation arrows to go through the song list and highlight the desired song.
Tips and Troubleshooting Chart Problem Recommended Action IR Sensor Inoperative • Check that the batteries are good in the remote control. • Check that the remote Control IR Sensor is not blocked. • Aim the remote control toward the IR Sensor being controlled.
Cleaning the Components Use care when touching or cleaning the components such as the DVD player or the discs. Do not use DVD lens cleaners for DVD players because the lens of the DVD optics can become contaminated by lubricants. Handle CDs and DVDs carefully.
P (Power): Press the P button to turn RSA on and off. Volume: Turn this knob to increase or to decrease the volume of the wired headphones. The left knob controls the left headphones and the right knob controls the right headphones.
PROG (Program): Press this button to go to the next preset radio station or channel set on the main radio. This function is inactive, with some radios, if the front seat passengers are listening to the radio. When a CD or DVD audio disc is playing, press this button to go to the beginning of the CD or DVD audio.
b g (Mute/Push to Talk): Press to silence the vehicle speakers only. Press again to turn the sound on. For vehicles with OnStar ® or Bluetooth systems press and hold b g for longer than two seconds to interact with those systems. See OnStar ® System on page 2-52 and Bluetooth ® on page 3-75 for more information.
XM™ Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out.
✍ NOTES 3-118.
Overview ........................................................ .4-2 Navigation System Overview ........................... .4-2 Getting Started .............................................. .4-4 Cleaning the Display ...............................
Overview Navigation System Overview Screen shown with Map Disc Inserted 4-2.
A. Source (AM, FM, XM, CD, etc.) Touch Screen Button. See Navigation Audio System on page 4-62 for more information. B. Clock Touch Screen Button. See “Setting the Clock” under Configure Menu on page 4-43 for more information. C. POI (Point of Interest) Touch Screen Button.
T. Map DVD Slot. See “Installing the Map DVD” under Maps on page 4-15 for information on how to install and eject a map DVD. U. Z (DVD Map Disc Eject) Key. See Maps on page 4-15 for more information. V. Mark Touch Screen Button. See “Adding Destinations to the Address Book” under Destination on page 4-25 for more information.
All functions are available when the vehicle is parked. Do the following before driving: • Become familiar with the navigation system operation, hard keys on the faceplate, and touch-sensitive screen buttons of the navigation system. • Set up the audio by presetting favorite stations, setting the tone, and adjusting the speakers.
When the navigation system is turned on, a screen may appear with the information below, and you must read and acknowledge the information it contains. { CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others.
Language — English/Metric To change the language of the navigation screens, see Driver Information Center (DIC) on page 3-47 for more information. To change the navigation screens from English or metric, see DIC Operation and Displays on page 3-48 for more information.
Storing Radio Station Presets To set preset radio stations, do the following: 1. Press O to turn the system on. 2. Press the AUDIO hard key and select the desired band (AM, FM, or XM (if equipped)). 3. Use the w (tuning) knob or the SEEK arrows to tune to the desired station.
Entering an Address and Point of Interest, and Storing Preset Destinations Entering an Address Enter a destination by inputting the city name first: 1. If the radio is already on with a map disc inserted, skip to Step 5. 2. Press O to turn the system on.
11. Select the Go screen button. A map screen, with the destination marked appears. 12. Select the route preference (Fastest, Shortest, or Other). The system calculates and highlights the route. 13. Select the Start Guidance screen button. You are now ready to start your route.
Storing Preset Destinations 1. If the radio is already on with a map disc inserted, skip to Step 5. 2. Press O to turn the system on. 3. Insert the DVD map disc. See “Installing the Map DVD” under Maps on page 4-15 for more information. 4. A caution may appear.
4. A caution may appear. Touch the OK screen button to proceed. 5. Press the DEST hard key. 6. Select one of the available preset destination screen buttons. A map screen, with the destination marked appears. 7. Select the route preference (Fastest, Shortest, or Other).
Features and Controls Using the Navigation System This section presents basic information needed to operate the navigation system. Use the hard keys located on the navigation system along with the available touch-sensitive screen buttons on the navigation screen to operate the system.
5 (Phone): Press to access calling through OnStar ® . See OnStar ® System on page 2-52 and Bluetooth ® on page 3-75 for more information. e (Sound): Press to access the Sound screen to adjust bass, midrange, treble, and Digital Signal Processing (DSP).
Alpha-Numeric Keyboard Letters of the alphabet, symbols, punctuation, and numbers, when available, displays on the navigation screen as an alpha or numeric keyboard. The alpha keyboard displays when the system requires entry of a city or street name. All characters are touch-sensitive screen buttons.
Limited Guidance Areas Any area that is not classified as detailed, is a limited guidance area. Limited guidance streets are displayed on the map but route guidance may not be given on these streets. Some POI categories, such as the city center POI category, and some street addresses are included in the limited guidance areas.
DVD Map Disc Messages If Disc Read Error appears on the display and/or the map disc comes out, it could be for one of the following reasons: • If the map disc was installed into the CD slot. See “Installing the DVD Map Disc” previously. • It is very hot, when the temperature returns to normal, the map disc should play.
Map Scales +/ − (Zoom In/Zoom Out): Touch the zoom in or out screen buttons or the scale on the bar to change the level of map detail. The scale appears on the screen once the zoom in or zoom out screen buttons are selected. The system adjusts the map accordingly.
Symbols The following symbols are the most common symbols that appear on a map screen. The vehicle is shown as this symbol. It indicates the current position and the direction the vehicle is traveling on the map. The destination symbol appears on the map, after a route has been planned, marking the final destination.
The distance and time to destination symbol indicates the distance and the estimated time remaining to the final destination, depending on the option selected. The straight line to distance symbol indicates the straight-line distance to the destination.
Three-dimensional (3–D) view mode changes the appearance of the map display to a road level view. The No GPS symbol appears when the vehicle is acquiring or not receiving a Global Positioning System (GPS) satellite signal. See Global Positioning System (GPS) on page 4-59 for more information.
1. Select one of the POI categories to display the POI icon at the top of the map screen. Select the POI category again to delete the POI icon. 2. Up to five categories can display on the map screen. 3. Press the Show POI screen button to add more POI icons.
Go: Select this screen button, next to the desired POI, to make this POI a destination or a stopover. Select a POI name to receive information about the POI. From this screen you can select: Address Book, Go, Map, or Call (if Bluetooth ® or OnStar ® personal calling is activated).
When approximately 1/4 mi (400 m) from the next maneuver, the screen displays the name and a detailed view of it. 3–D Lane Guidance Some major metropolitan areas may include a 3–D lane guidance feature for highway exits and junctions. This feature gives you an enhanced representation of the exits and junctions on the route.
Dual Mode This dual screen symbol displays when the screen is in dual mode. Dual mode displays the route on half of the screen and a maneuver or Interstate Exit list on the other half. The Interstate Exit list advises of approaching exits. Press this button to switch between dual screen and full screen which displays the entire route.
To enter a destination by inputting the city name first: 1. Press the DEST hard key. 2. Select the 2 screen button. 3. Select the state/province screen button, if needed, to change the current state or province. A list of all of the available states and provinces appear.
7. Select the Go screen button. The map screen, with the destination marked displays. 8. Select the route preference (Fastest, Shortest, or Other). The system calculates and highlights the route. 9. Select the Start Guidance screen button. The route is now ready to be started.
To enter a destination by entering a cross street: 1. Press the DEST hard key. 2. Select the 2 screen button. 3. Select the state/province screen button, if needed, to change the current state or province. A list of all of the available states and provinces appear.
Point of Interest (POI) The Point of Interest (POI) destination entry method lets you select a destination from the POI list. i Point of Interest: Touch to access the POI (Point of Interest) screen. From this screen you have two options to select/enter a destination.
To use the point of interest destination entry method by selecting a category: 1. Press the DEST hard key. 2. Select the i screen button. 3. Select the Browse POI Categories screen button to view the list of POI categories. 4. Select a category. The system displays available POI names in the selected category.
To use the address book entry method: 1. Press the DEST hard key. 2. Select the g screen button. A list of the address book addresses display. 3. Select the Go screen button next to the destination. The map screen, with the destination marked displays.
To use the previous destination entry method: 1. Press the DEST hard key. 2. Select the / screen button. 3. Select a previous destination from the list. Use the arrow to the right of the destination to view the entire destination name as necessary. Use the scroll arrows to the left to scroll through the list.
To use this destination entry method: 1. Press the DEST hard key. 2. Select the ) screen button. A map screen displays with the scrolling symbol. 3. Use the 0 / 1 screen buttons and touch on the map to find the area that you would like to select as your destination.
To use the coordinates destination entry method: 1. Press the DEST hard key. 2. Select the From Map screen button. 3. Select the Map Coordinates screen button. 4. Select Latitude and select either N (north) or S (south) to enter the direction of the latitude coordinate.
To use the preset destination entry method: 1. Press the DEST hard key. 2. Select the desired preset destination screen button. The screen buttons are labeled with the name that was selected for the destination when it was stored. The map screen, with the destination marked displays.
Using OnStar ® Destination Download Press the blue OnStar button and an Advisor can locate a point-of-interest or an address and download the necessary information or coordinates to your navigation system. Once the destination is downloaded, the navigation system will search for the address in the mapping disc’s database.
Route Guidance Not Active If an OnStar destination is downloaded while route guidance is not active, the navigation system displays an OnStar Destination Download Screen and operations will continue a.
Map Destination Screen Functions If the map screen is used to show destination, it will have map screen capabilities such as Go, Mark, Zoom, Scroll, etc. The address is shown at the top of the screen. Getting Started on Your Route Once a destination has been entered, there are several functions that can be performed.
Turn List Turn List: Touch to view the list of turn maneuvers for the entire route and to avoid turns on the route. r / q (Scroll Arrows): Touch the up and down arrows to scroll through the list of maneuvers. Avoid: Touch this screen button, next to the adjacent street name, to avoid the maneuver.
r / [ (Fast Forward Scroll): Select to scroll to the next stopover or to the final destination. The u (fast forward skip) button changes to a fast speed fast forward. u (Fast Forward Skip): Select to go to the next stopover or to the final destination.
To add a stopover: 1. Press the DEST hard key. 2. Select the Add Stopover screen button. This button only appears if a route has been calculated. 3. Using the desired method of entering a destination, enter the stopover. See “Destination” previously for more information.
Adding Destinations to the Address Book There are two ways to add a destination to the address book: • To add the current vehicle position to the address book, press the Mark screen button from the map screen. The system automatically saves the current vehicle information in the address book.
To store an address book entry as a preset destination: 1. Select the CONFIG hard key. 2. Select the Nav screen button or press the CONFIG key until Nav is selected or touch the Nav screen button. 3. Select the Edit/View screen button. 4. Select the address book entry to be stored as the preset destination.
Sound Press the CONFIG key to enter the configure menu options, then press the CONFIG key repeatedly until Sound is selected or touch the Sound screen button to make speaker and DSP (Digital Signal Processing) adjustments. See “Sound Menu” under, Navigation Audio System on page 4-62 for more information.
Voice Prompt Voice Prompt: Touch the Voice Prompt screen button to change the volume of the voice prompts or to turn voice guidance on and off. Volume: Touch the + (plus) or − (minus) screen buttons to increase or to decrease the volume of the voice prompts.
Edit Address Book — Edit/View To edit the name of an address book: 1. Select the CONFIG hard key. 2. Select the NAV screen button. 3. Select the Edit/View Address Book screen button. 4. Select the Address book entry. 5. Touch the Name screen button and use the alpha keyboard to edit or add the name.
4. Select the Add Voice Tag screen button. 5. The system will ask for you to state the name. You will have four seconds to state the name. The system will respond back with the name and prompt you to repeat the name for confirmation. To delete an address book entry: 1.
Of f-Road Mode To turn the Off-road mode on or of f, do the following: 1. Press the CONFIG hard key. 2. Press the Nav screen button. 3. Press the Off-Road mode screen button.
Three types of traff ic information for major roadways are displayed on the navigation system: • Unscheduled traff ic incident data, such as accidents and disabled vehicles • Scheduled traff ic in.
Traf fic Icon The Traff ic Icon appears on the Traffic Tab, next to the word Traff ic, when traffic is found in the local area. The Traff ic Icon has three different condition displays. These are: Condition Traff ic Status Icon • No XM NavTraff ic™ subscription.
Locations and Information of Traf fic Conditions The system may take some time to sort the information. The list of traff ic conditions display in the order of distance from the vehicle, up to approximately 75 mi (125 km). With a route planned, the system defaults to list traff ic events on your route.
While the vehicle is moving, the traff ic list up or down, scroll arrows are limited to a maximum of four pages. No more than four pages of traff ic events may be viewed while the vehicle is moving. 2. Select a traff ic condition to get more detailed information of the event.
Traff ic Flow Status — This touch screen button is used to enable or disable the green, yellow, red and orange arrows shown beside the roads and used to show the traff ic flow or extent of a traffic event. • Black indicates a closed road segment • Red indicates significantly impaired traff ic flow with average speed of less than 25 mph.
On-Route Select the On Route touch screen button to display all events ahead on the current active route. If no traff ic events have been reported on route, No Traff ic Events Reported On route displays. Name Select the Name touch screen button to display traff ic events in the order of distance.
After selecting the INFO (information) screen button, the type of traff ic condition, the street name, and a description of the traff ic condition displays.
Detailed Traf fic Event Screens The detailed Traff ic Event screens are used to display additional details of a traff ic event condition. This screen may display if: • Scrolling to an event on the map and then pressing INFO. • Selecting a traff ic event listed on the Traffic Event List screen.
Avoid: This button is used to avoid the location of an event on the route. If selected, a new route is calculated and the related traff ic event is avoided. After the new route has been calculated, the navigation system goes to the full map screen and shows the new route.
Brightness/Contrast/Mode Touch this screen button to change the brightness, contrast, and mode of the display. ] (Brightness): Touch the + (plus) or − (minus) screen buttons to increase or decrease the brightness of the screen. _ (Contrast): Touch the + (plus) or − (minus) screen buttons to increase or decrease the contrast of the screen.
Global Positioning System (GPS) The navigation system determines the position of the vehicle by using satellite signals, various vehicle signals, and map data.
Vehicle Positioning At times, the position of the vehicle on the map may be inaccurate due to one or more of the following reasons: • Road system has changed. • Vehicle is driving on slippery road surfaces such as in sand, gravel, and/or snow. • Vehicle is traveling on winding roads.
Problems with Route Guidance Inappropriate route guidance may occur under one or more of the following conditions: • You have not turned onto the road indicated. • Route guidance may not be available when using automatic rerouting for the next right or left turn.
If you have any questions about the operation of the navigation system or the update process, contact the GM Nav Disc Center toll-free phone number, 1-877-NAV-DISC (1-877-628-3472) or go to the center’s website, gmnavdisc.
Playing the Radio O / n (Power/Volume): Press to turn the audio system on and off. Turn to increase or to decrease the volume. Press and hold for more than two seconds to turn off the navigation system, the Rear Seat Entertainment (RSE) video screen, and Rear Seat Audio (RSA).
If you do not want to view a split screen or you are not on a map screen, press the AUDIO hard key. AM/FM/XM: Touch the source (AM, FM, or XM, if equipped) screen button or press the AUDIO key repeatedly until the desired source is highlighted.
The station information appears on the display. See “Radio Menu” later in this section to add and remove XM categories from the category list. Removed categories do not appear on the category list screen or when the right and left arrow category screen buttons are used.
Sound Menu e (Sound): Press this key or press the CONFIG key to access the Sound menu to adjust the treble, midrange, bass, fade, balance, and Digital Signal Processing (DSP). The system automatically stores audio adjustment settings as changes are made for each audio source including AM, FM, XM (if equipped), CD, and AUX.
Digital Signal Processing (DSP) The system has Digital Signal Processing (DSP). DSP provides a choice of four different listening experiences. DSP can be used while listening to the audio system. Not all DSP modes are available for all source types. The type of DSP selected is displayed on the status line.
Limit Features While Driving Touch the Limit Features While Driving screen button to turn on and off the ability to limit functions while driving. When this screen button is highlighted, the following.
Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information.
XM™ Radio Messages XL (Explicit Language Channels): XL on the radio display, after the channel name, indicates content with explicit language. These channels, or any others, can be blocked at a customer’s request by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated and no action is required.
CD Player The player can be used for CD, MP3, DVD audio, and as a DVD video player. See DVD Player on page 4-78 for more information about DVD audio and video. Six-Disc CD Player While playing a CD, the navigation system is available. When you insert a CD, the CD tab displays.
To load multiple discs, do the following: 1. Press and hold the load hard key and follow the screen message displayed. 2. When the system displays “Insert Disc (number)”, insert the disc partway into the slot, label side up. The system will pull it in.
r (Rewind): Touch and hold this button to rewind quickly through a track selection. You will hear sound at a reduced volume. Release this button to stop rewinding. The display will show the elapsed time of the track. [ (Forward): Touch and hold this button to fast forward quickly through a track selection.
• It is recommended that there is a maximum of 192 files on a disc. • The files can be recorded on a CD-R or CD-RW with a maximum capacity of 700MB. • DVD with MP3 are not playable on this system. Root Directory The root directory will be treated as a folder.
Playing an MP3 While playing a CD, the navigation system is available. When you insert a CD, the CD tab will display. If you select a DSP setting for the CD, it will be activated each time you play a CD. If you turn off the ignition or radio with a CD in the player, it will stay in the player.
Z (Eject): To eject a disc, do the following: 1. Press the eject hard key. 2. The system will display “Ejecting Disc”. Press the DISC screen button to display the Disc Changer screen. Select the disc to eject. If a selection is not made, the system will eject the disc from the current slot.
qr (Folder/Artist/Album): Select the left or right arrow to go to the previous or next folder, artist, or album on the disc. Press the middle screen button, with the folder, artist, or album name, to sort the MP3 by folder, artist, or album. It may take a few minutes for the system to sort the MP3.
DVD Player The player can be used for DVD audio and DVD video. DVD video will not display on the navigation screen unless the vehicle is in PARK (P). It will operate on the rear seat entertainment screens while the vehicle is moving.
3. Once a disc is loaded, the system will display “Insert Disc (number)” again. Load the next disc. Repeat this procedure for each disc. The player takes up to six discs, do not try to load more than six. The system will not display the disc types when loading all, until the discs have been read by the system.
DVD Menu Options Once a DVD starts to play, the menu options and cursor screen buttons will automatically appear. To display the menu Options screen button while a DVD is playing, touch anywhere on the screen. Options: Select this screen button to view the menu option screen buttons.
Hide Options: Press this screen button to remove all menu options from the display, except Options and Cursor. Top Menu: Touch this button to display the first menu of the DVD. This is not available on all DVDs. Menu: Touch this button to display the DVD menu of the current area of the DVD that is playing.
! (Brightness): Touch the up or down screen arrows to increase or decrease the brightness of the navigation screen. _ (Contrast): Touch the up or down screen arrows to increase or decrease the contrast of the navigation screen.
Subtitle Language: Touch English, Francais, Espanol, Italiano, or Deutsch to change the default language of the subtitles that the DVD player uses for each disc. The subtitle language must be available on the disc. The subtitle language may vary for each DVD.
DVD Messages If Disc Read Error appears on the display and/or the DVD comes out, it could be for one of the following reasons: • If a disc was inserted with an invalid or unknown format. • If the disc is not from a correct region. • If the map DVD disc was installed into the DVD audio/video slot.
Do not add any label to a CD or DVD, it could get caught in the player. If a CD or DVD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD or DVD with a soft marker. Auxiliary Devices The vehicle may have a rear entertainment system (RSE) with a second and third row screen.
3. For the second row display select the Rear AUX screen button next to Rear Display 1 and for the third row display select the Rear AUX screen button next to Rear Display 2. Each screen works independently of the other. The second row screen can watch a DVD while the third row screen can use the auxiliary device.
Helpful Hints for Stating Commands • When a multiple command is available, choose the command that works best. • Words that are in brackets are optional. For example, for the command Radio [band] [select] FM, stating Radio FM or Radio select FM are both valid commands.
Storing Voice Tags From the address book entry information page, press the Add Voice tag screen button. The system responds “Name Please?” and you will have four seconds to record a name. The system asks for confirmation of the name before saving it as a voice tag.
CD Commands The following are CD, MP3, and DVD commands that can be accessed by clearly stating the commands exactly as they are written. CD, DVD, Disc: Use this command to select a CD, DVD, or disc that is currently loaded. CD, DVD, Disc, [select] track (one, two, three, etc.
✍ NOTES 4-90.
Your Driving, the Road, and the Vehicle ........... .5-2 Driving for Better Fuel Economy ...................... .5-2 Defensive Driving .......................................... .5-2 Drunk Driving ................................................ .5-3 Control of a Vehicle .
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops.
Drunk Driving { CAUTION: Drinking and then driving is very dangerous. Your reflexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking.
Braking See Brake System Warning Light on page 3-39 . Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second.
Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on.
Braking in Emergencies ABS allows the driver to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking. Brake Assist This vehicle has a Brake Assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions.
If the system fails to turn on or activate, the StabiliTrak light along with one of the following messages will be displayed on the Driver Information Center (DIC): TRACTION CONTROL OFF, SERVICE TRACTION CONTROL, STABILITRAK OFF, SERVICE STABILITRAK.
It is recommended to leave the system on for normal driving conditions, but it may be necessary to turn the system off if the vehicle is stuck in sand, mud, ice or snow, and you want to “rock” the vehicle to attempt to free it.
Magnetic Ride Control™ The vehicle may have the MagneRide control system. MagneRide constantly checks speed, wheel position, lift/dive and steering of the vehicle. The damping force for each shock absorber and adjustment level is chosen for the best ride and handling.
Steering Power Steering If the vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. If power steering assist is lost because the engine stops or the system is not functioning, the vehicle can be steered but it will take more effort.
An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o’clock positions, it can be turned a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Passing Passing another vehicle on a two-lane road can be dangerous. To reduce the risk of danger while passing: • Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait. • Watch for traff ic signs, pavement markings, and lines that could indicate a turn or an intersection.
While driving on a surface with reduced traction, try your best to avoid sudden steering, acceleration, or braking, including reducing vehicle speed by shifting to a lower gear. Any sudden changes could cause the tires to slide. You may not realize the surface is slippery until the vehicle is skidding.
Before You Go Of f-Roading • Have all necessary maintenance and service work done. • Make sure there is enough fuel, that fluid levels are where they should be, and that the spare tire, if the vehicle has one, is fully inflated. • Be sure to read all the information about all-wheel-drive vehicles in this manual.
Loading Your Vehicle for Of f-Road Driving { CAUTION: • Cargo on the load floor piled higher than the seatbacks can be thrown forward during a sudden stop. You or your passengers could be injured. Keep cargo below the top of the seatbacks. • Unsecured cargo on the load floor can be tossed about when driving over rough terrain.
Environmental Concerns Off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow.
Controlling the vehicle is the key to successful off-road driving. One of the best ways to control the vehicle is to control the speed. At higher speeds: • You approach things faster and have less time to react. • There is less time to scan the terrain for obstacles.
When driving over obstacles or rough terrain, keep a firm grip on the steering wheel. Ruts, troughs, or other surface features can jerk the wheel out of your hands. When driving over bumps, rocks, or other obstacles, the wheels can leave the ground. If this happens, even with one or two wheels, you cannot control the vehicle as well or at all.
Approaching a Hill When you approach a hill, decide if it is too steep to climb, descend, or cross. Steepness can be hard to judge. On a very small hill, for example, there may be a smooth, constant incline with only a small change in elevation where you can easily see all the way to the top.
• Sound the horn as you approach the top of the hill to let opposing traff ic know you are there. • Use headlamps even during the day to make the vehicle more visible to oncoming traff ic. { CAUTION: Driving to the top (crest) of a hill at full speed can cause an accident.
Driving Downhill When off-roading takes you downhill, consider: • How steep is the downhill? Will I be able to maintain vehicle control? • What is the surface like? Smooth? Rough? Slippery? Hard-p.
Driving Across an Incline An off-road trail will probably go across the incline of a hill. To decide whether to try to drive across the incline, consider the following: { CAUTION: Driving across an incline that is too steep will make your vehicle roll over.
Stalling on an Incline { CAUTION: Getting out on the downhill (low) side of a vehicle stopped across an incline is dangerous. If the vehicle rolls over, you could be crushed or killed. Always get out on the uphill (high) side of the vehicle and stay well clear of the rollover path.
Hard packed snow and ice offer the worst tire traction. On these surfaces, it is very easy to lose control. On wet ice, for example, the traction is so poor that you will have diff iculty accelerating. And, if the vehicle does get moving, poor steering and diff icult braking can cause it to slide out of control.
If the water is not too deep, drive slowly through it. At faster speeds, water splashes on the ignition system and the vehicle can stall. Stalling can also occur if you get the tailpipe under water. If the tailpipe is under water, you will never be able to start the engine.
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or flowing water.
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer .
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all fluid levels and brakes, tires, cooling system, and transmission.
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction.
Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Service on page 8-7 . To get help and keep everyone in the vehicle safe: • Turn on the Hazard Warning Flashers on page 3-6 .
Repeat this until help arrives but only when you feel really uncomfortable from the cold. Moving about to keep warm also helps. If it takes some time for help to arrive, now and then when you run the engine, push the accelerator pedal slightly so the engine runs faster than the idle speed.
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible.
Notice: Never use recovery hooks to tow the vehicle. Your vehicle could be damaged and it would not be covered by warranty. For vehicles with recovery hooks at the front of the vehicle, you can use them if you are stuck off-road and need to be pulled to some place where you can continue driving.
Tire and Loading Information Label A vehicle specific Tire and Loading Information label is attached to the center pillar (B-pillar). With the driver’s door open, you will find the label attached below the door lock post (striker).
Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Item Description Total A Vehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Cargo Weight = 700 lbs (.
Item Description Total A Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle’s tire and loading information label for specific information about your vehicle’s capacity weight and seating positions.
Certification/Tire Label A vehicle specific Certification/Tire label is attached to the rear edge of the driver’s door. The label shows the size of your vehicle’s original tires and the inflation pressures needed to obtain the gross weight capacity of your vehicle.
Using heavier suspension components to get added durability might not change your weight ratings. Ask your dealer to help you load your vehicle the right way. If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes.
The system is activated when the ignition key is turned to RUN and will automatically adjust vehicle height thereafter. The system may exhaust (lower vehicle height) for up to 10 minutes after the ignition key has been turned to LOCK. You may hear the air compressor operating when the height is being adjusted.
All-Wheel-Drive Vehicles Dinghy and Dolly Towing Notice: Towing an all-wheel-drive vehicle with all four wheels on the ground, or even with only two of its wheels on the ground, will damage drivetrain components. Do not tow an all-wheel-drive vehicle with any of its wheels on the ground.
Two-Wheel-Drive Vehicles Dinghy Towing Notice: If a two-wheel-drive vehicle is towed with all four wheels on the ground, the transmission could be damaged. The repairs would not be covered by the vehicle warranty. Do not tow a two-wheel-drive vehicle with all four wheels on the ground.
Two-wheel-drive vehicles should not be towed with the rear wheels on the ground. Two-wheel-drive transmissions have no provisions for internal lubrication while being towed. Dolly Towing (Rear Wheels Of f the Ground) Use the following procedure to dinghy tow a two-wheel-drive vehicle from the rear: 1.
Autoride ® With this feature, improved vehicle ride and handling is provided under a variety of passenger and loading conditions. The system is fully automatic and uses a computer controller to continuously monitor vehicle speed, wheel to body position, lift/dive and steering position of the vehicle.
To identify the trailering capacity of the vehicle, read the information in “Weight of the Trailer” that appears later in this section. Trailering is different than just driving the vehicle by itself. Trailering means changes in handling, acceleration, braking, durability and fuel economy.
Weight of the Trailer How heavy can a trailer safely be? It depends on how the rig is used. For example, speed, altitude, road grades, outside temperature and how much the vehicle is used to pull a trailer are all important. It can depend on any special equipment on the vehicle, and the amount of tongue weight the vehicle can carry.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Trailering may be limited by the vehicle’s ability to carry tongue weight. Tongue weight cannot cause the vehicle to exceed the GVWR (Gross Vehicle Weight Rating) or the RGAWR (Rear Gross Axle Weight Rating). The effect of additional weight may reduce the trailering capacity more than the total of the additional weight.
The effect of tongue weight is about 1.5 times the actual weight. Dividing the 900 lbs (408 kg) by 1.5 leaves only 600 lbs (272 kg) of tongue weight that can be handled. Since tongue weight is usually at least 10 percent of total loaded trailer weight, expect that the largest trailer the vehicle can properly handle is 6,000 lbs (2 721 kg).
When pulling a trailer that, when loaded, will weigh more than 5,000 lbs (2 270 kg) be sure to use a properly mounted weight-distributing hitch and sway control of the proper size. This equipment is very important for proper vehicle loading and good handling when driving.
Safety Chains Always attach chains between the vehicle and the trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer.
Operating the vehicle in Tow/Haul when lightly loaded or with no trailer at all will not cause damage. However, there is no benefit to the selection of Tow/Haul when the vehicle is unloaded. Such a selection when unloaded may result in unpleasant engine and transmission driving characteristics and reduced fuel economy.
Towing a trailer requires a certain amount of experience. Get to know the rig before setting out for the open road. Get acquainted with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now longer and not as responsive as the vehicle is by itself.
Driving On Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the brakes might have to be used so much that they would get hot and no longer work well. Vehicles can tow in D (Drive).
{ CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If the engine has been left running, the vehicle can move suddenly. You or others could be injured.
Maintenance When Trailer Towing The vehicle needs service more often when pulling a trailer. See this manual’s Maintenance Schedule or Index for more information. Things that are especially important in trailer operation are automatic transmission fluid, engine oil, axle lubricant, belts, cooling system and brake system.
Electric Brake Control Wiring Provisions These wiring provisions are included with the vehicle as part of the heavy-duty trailer wiring package. These provisions are for an electric brake controller.
✍ NOTES 5-58.
Service ........................................................... .6-3 Accessories and Modifications ......................... .6-3 California Proposition 65 Warning .................... .6-4 California Perchlorate Materials Requirements .... .6-4 Doing Your Own Service Work .
Tire Pressure Monitor System ........................ .6-64 Tire Pressure Monitor Operation .................... .6-65 Tire Inspection and Rotation .......................... .6-69 When It Is Time for New Tires ...................... .6-70 Buying New Tires .
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories an.
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
This vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your Airbag-Equipped Vehicle on page 1-93 . Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7-17 .
Gasoline Specifications At a minimum, gasoline should meet ASTM specification D 4814 in the United States or CAN/CGSB-3.5 or 3.511 in Canada. Some gasolines contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT).
However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels. Notice: This vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol.
At a minimum, E85 should meet ASTM Specification D 5798. By definition, this means that fuel labeled E85 will have an ethanol content between 70% and 85%. Filling the fuel tank with fuel mixtures that do not meet ASTM specifications can affect driveability and could cause the malfunction indicator lamp to come on.
Filling the Tank { CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling. Do not smoke if you are near fuel or refueling the vehicle.
To open the fuel door, push the rearward center edge in and release and it will open. To remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right. While refueling, hang the tethered fuel cap from the hook on the fuel door.
If the vehicle has a Driver Information Center (DIC), the TIGHTEN GAS CAP message displays if the fuel cap is not properly installed. { CAUTION: If a fire starts while you are refueling, do not remove the nozzle. Shut off the flow of fuel by shutting off the pump or by notifying the station attendant.
Checking Things Under the Hood { CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION: Things that burn can get on hot engine parts and start a fire.
Hood Release To open the hood: 1. Pull the handle with this symbol on it. It is located inside the vehicle to the lower left of the steering wheel. 2. Then go to the front of the vehicle and locate the secondary hood release, near the center of the grille.
Engine Compartment Overview If the vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. When you open the hood on the 6.2L engine this is what you will see: 6-14.
A. Engine Air Cleaner/Filter on page 6-19 . B. Coolant Surge Tank and Pressure Cap. See Cooling System on page 6-24 . C. Remote Positive (+) Terminal. See Jump Starting on page 6-40 . D. Battery on page 6-39 . E. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 6-15 .
When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 6-113 .
What Kind of Engine Oil to Use Look for three things: • GM4718M This vehicle’s engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identified as synthetic. However, not all synthetic oils will meet this GM standard.
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM standards are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty.
If the CHANGE ENGINE OIL SOON message comes back on when the vehicle is started, the Engine Oil Life System has not reset. Repeat the procedure. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer.
3. Remove the engine air cleaner/filter from the housing. Care should be taken to dislodge as little dirt as possible. 4. Clean the engine air cleaner/filter sealing surfaces and the housing. 5. Inspect or replace the engine air cleaner/filter. 6. Reinstall the cover and tighten the screws.
Notice: Use of the incorrect automatic transmission fluid may damage the vehicle, and the damages may not be covered by the vehicle’s warranty. Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 7-13 . Change the fluid and filter at the intervals listed in the Maintenance Schedule.
Cold Check Procedure Use this procedure only as a reference to determine if the transmission has enough fluid to be operated safely until a hot check procedure can be made. The hot check procedure is the most accurate method to check the fluid level.
Hot Check Procedure Use this procedure to check the transmission fluid level when the transmission fluid temperature is between 160°F and 200°F (71°C and 93°C). The hot check is the most accurate method to check the fluid level. The hot check should be performed at the first opportunity in order to verify the cold check.
Consistency of Readings Always check the fluid level at least twice using the procedures described. Consistency (repeatable readings) is important to maintaining proper fluid level. If fluid is added, it may take 15 minutes or longer to obtain an accurate reading because of residual fluid draining down the dipstick tube.
{ CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
What to Use { CAUTION: Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture.
Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant surge tank. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down.
How to Add Coolant to the Surge Tank { CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Notice: This vehicle has a specific coolant fill procedure.
If no coolant is visible in the surge tank, add coolant as follows: 1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one full turn.
4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan.
You may decide not to lift the hood when this warning appears, but instead get service help right away. See Roadside Service on page 8-7 . If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running.
If No Steam Is Coming From The Engine Compartment The ENGINE OVERHEATED STOP ENGINE or the ENGINE OVERHEATED IDLE ENGINE message, along with a low coolant condition, can indicate a serious problem. If you get an engine overheat warning, but see or hear no steam, the problem may not be too serious.
Overheated Engine Protection Operating Mode If an overheated engine condition exists and the ENGINE POWER IS REDUCED message is displayed, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage. In this mode, you will notice a loss in power and engine performance.
When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired.
Adding Washer Fluid The vehicle has a low washer fluid message in the DIC that comes on when the washer fluid is low. The message is displayed for 15 seconds at the start of each ignition cycle. When the WASHER FLUID LOW ADD FLUID message displays, you will need to add washer fluid to the windshield washer fluid reservoir.
Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 6-14 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: • The brake fluid level goes down because of normal brake lining wear.
{ CAUTION: If too much brake fluid is added, it can spill on the engine and burn, if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake fluid only when work is done on the brake hydraulic system. See “Checking Brake Fluid” in this section.
What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 7-13 . Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications in Capacities and Specifications on page 6-113 .
Vehicle Storage { CAUTION: Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 6-40 for tips on working around a battery without getting hurt. Infrequent Usage: If the vehicle is driven infrequently, remove the black, negative ( − ) cable from the battery.
Notice: If the other vehicle’s system is not a 12-volt system with a negative ground, both vehicles can be damaged. Only use vehicles with 12-volt systems with negative grounds to jump start your vehicle. 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles are not touching each other.
The remote negative (-) terminal is a stud located on the right front of the engine, where the negative battery cable attaches. See Engine Compartment Overview on page 6-14 for more information on the location of the remote positive (+) and remote negative ( − ) terminals.
CAUTION: (Continued) Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately. { CAUTION: Fans or other moving engine parts can injure you badly.
8. Now connect the black negative ( − ) cable to the negative ( − ) terminal of the good battery. Use a remote negative ( − ) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative ( − ) cable does not go to the dead battery.
To disconnect the jumper cables from both vehicles do the following: 1. Disconnect the black negative ( − ) cable from the vehicle that had the bad battery. 2. Disconnect the black negative ( − ) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery.
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 7-13 . Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle fluid unless you suspect there is a leak or you hear an unusual noise.
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 7-13 . Front Axle When to Check and Change Lubricant It is not necessary to regularly check front axle fluid unless you suspect there is a leak or you hear an unusual noise.
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 7-13 . Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim of the headlamps have been preset at the factory and should need no further adjustment.
Headlamp aiming is done with the vehicle’s low-beam headlamps. The high-beam headlamps will be correctly aimed if the low-beam headlamps are aimed properly. To adjust the vertical aim: 1. Open the hood. See Hood Release on page 6-13 for more information.
7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly. The adjustment screw can be turned with a E8 Torx ® socket. 8. Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line.
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 6-53 . For any bulb changing procedure not listed in this section, contact your dealer/retailer. High Intensity Discharge (HID) Lighting { CAUTION: The low beam high intensity discharge lighting system operates at a very high voltage.
2. Remove the two screws from the taillamp assembly. 3. Pull the taillamp assembly rearward until you disengage the inner pins on the taillamp assembly from the vehicle. 4. Press the release tab, if the bulb socket has one, and turn the socket counterclockwise to remove it from the taillamp assembly.
License Plate Lamp 1. Remove the two screws holding each of the license plate lamps to the molding that is part of the liftgate. 2. Twist and pull the license plate lamp forward through the molding opening. 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 7-4 . Replacement blades come in different types and are removed in different ways. To replace the wiper blade assembly: 1.
Backglass Wiper Blade Replacement 1. Lift the wiper blade assembly up and out of the park rest position. 2. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position, so care should be used when pulling it away from the vehicle.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer.
Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The following illustration is an example of a typical P-Metric tire sidewall. (A) Tire Size : The tire size code is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type, and service description.
(G) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommended tire pressure see Inflation - Tire Pressure on page 6-62 and Loading the Vehicle on page 5-33 .
Tire Terminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories.
GAWR RR : Gross Axle Weight Rating for the rear axle. See Loading the Vehicle on page 5-33 . Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure.
Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated. Sidewall : The portion of a tire between the tread and the bead.
Inflation - Tire Pressure If your vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right.
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are underinflated. Check the tire’s inflation pressure when the tires are cold.
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle.
Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.
Using the DIC, tire pressure levels can be viewed by the driver. For additional information and details about the DIC operation and displays see DIC Operation and Displays on page 3-48 and DIC Warnings and Messages on page 3-56 .
• One or more TPMS sensors are missing or damaged. The DIC message and the TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer/ retailer for service. • Replacement tires or wheels do not match your vehicle’s original equipment tires or wheels.
You have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over.
Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, for signs of wear or damage. See When It Is Time for New Tires on page 6-70 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km).
Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 6-65 . Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 6-113 . { CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
Dif ferent Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this could affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover.
Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis.
Used Replacement Wheels { CAUTION: Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Changing a Flat Tire If your vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 3-6 .
Removing the Spare Tire and Tools The equipment you will need is stored under the storage tray, which is located on the driver’s side trim panel (over the rear wheelhouse). 1. Remove the tray to access the tools by pulling up on the finger depression under the jack symbol.
The tools you will be using include the following: A. Jack B. Wheel Blocks C. Jack Handle D. Jack Handle Extensions E. Wheel Wrench To access the spare tire: A. Hoist Assembly B. Hoist Shaft C. Hoist Shaft Access Cover/Hole D. Jack Handle Extensions E.
1. To reach the hoist shaft access cover (C), you will first need to remove the hitch cover. Remove it by turning the two fasteners located at the bottom of the cover counterclockwise and then pull the cover down and rotate towards you. 2. Open the hoist shaft access cover (C) on the bumper to access the spare tire lock (K).
5. Insert the open end of the extension (J) through the hole in the rear bumper (I) (hoist shaft access hole). Be sure the hoist end (J) of the extension (D) connects to the hoist shaft (B). The ribbed square end of the extension is used to lower the spare tire.
8. Tilt the tire toward the vehicle with some slack in the cable to access the tire/wheel retainer (G). Separate the retainer from the guide pin by sliding the retainer up the pin while pressing down on the latch.
Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6-78 for more information. 2. To remove the center cap, place the chiseled end of the wheel wrench in the slot on the wheel and gently pry the cap out.
{ CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
Rear Tire Flat: If the flat tire is on a rear tire of the vehicle, you will need to use the jack handle (B) and both jack handle extensions (C). Attach the wheel wrench (D) to the jack handle extensions (C). Attach the jack handle (B) to the jack (A).
{ CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
{ CAUTION: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Secondary Latch System Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire from suddenly falling off your vehicle. For the secondary latch to work, the spare must be installed with the valve stem pointing down.
5. If the spare does not lower, turn the wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed. 6. Stand the wheel blocks on their shortest ends, with the backs facing each other. 7. Place the bottom edge of the jack (A) on the wheel blocks (B), separating them so that the jack is balanced securely.
9. Position the center lift point of the jack under the center of the spare tire. 10. Turn the wrench clockwise to raise the jack until it lifts the end fitting. 11. Continue raising the jack until the spare tire stops moving upward and is held firmly in place.
Storing a Flat or Spare Tire and Tools { CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
1. Put the tire (H) on the ground at the rear of the vehicle with the valve stem pointed down and to the rear. 2. Tilt the tire toward the vehicle. Separate the tire/wheel retainer (G) from the guide pin. Pull the pin through the center of the wheel. Tilt the retainer down and through the center wheel opening.
4. Insert the open end of the extension (J) through the hole in the rear bumper (I) (hoist shaft access hole). 5. Raise the tire part way upward. Make sure the retainer is fully seated across the underside of the wheel and centered in the wheel opening.
To store the tools: A. Wheel Blocks B. Tool Bag with Jack Tools C. Retaining Bracket D. Wing Nut Retaining Tool Bag E. Jack F. Wing Nut Retaining Wheel Blocks G. Jack Knob 1. Return the tools (wheel wrench, jack handle, and jack handle extensions) to the tool bag (B).
Spare Tire Your vehicle, when new, had a fully-inflated spare tire. A spare tire may lose air over time, so check its inflation pressure regularly. See Inflation - Tire Pressure on page 6-62 and Loading the Vehicle on page 5-33 for information regarding proper tire inflation and loading your vehicle.
Notice: Using abrasive cleaners when cleaning glass surfaces on the vehicle, could scratch the glass and/or cause damage to the rear window defogger. When cleaning the glass on the vehicle, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in the vehicle’s breathing space.
Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For any soil, always try to remove it first with plain water or club soda.
TEHAMA™ Leather The leather surface on the seat was not designed to be aggressively cleaned using any commercial product. Use a well wrung cloth dampened with water to remove dust. Do not use a wet cloth or saturate the leather surface with water. Allow the leather to dry naturally.
Wood Panels Use a clean cloth moistened in warm, soapy water (use mild dish washing soap). Dry the wood immediately with a clean cloth. Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap.
Rinse the vehicle well, before washing and after to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting.
Windshield, Backglass, and Wiper Blades Clean the outside of the windshield and backglass with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when you clean the blades.
The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because they could damage the surface. Do not use chrome polish on aluminum wheels.
Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection.
Service Parts Identification Label This label is on the inside of the glove box. It is very helpful if parts need to be ordered. The label has the following information: • Vehicle Identification Number (VIN) • Model designation • Paint information • Production options and special equipment Do not remove this label from the vehicle.
Fuses and Circuit Breakers If the vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. The wiring circuits in the vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links.
The vehicle may not use all of the fuses shown. Fuses Usage 1 Rear Seats 2 Rear Accessory Power Outlet 3 Steering Wheel Controls Backlight 4 Driver Door Module Fuses Usage 5 Dome Lamps, Driver Side Tu.
Fuses Usage 21 Power Door Lock 1 (Lock Feature) 22 Driver Information Center (DIC) 23 Rear Wiper 24 Cooled Seats 25 Driver Seat Module, Remote Keyless Entry System 26 Driver Power Door Lock (Unlock Fe.
Harness Connector Usage HEADLINER 3 Headliner Harness Connector 3 HEADLINER 2 Headliner Harness Connector 2 HEADLINER 1 Headliner Harness Connector 1 SEO/UPFITTER Special Equipment Option Upfitter Ha.
Fuses Usage 1 Right Trailer Stop/Turn Lamp 2 Electronic Stability Suspension Control, Automatic Level Control Exhaust 3 Left Trailer Stop/Turn Lamp 4 Engine Controls Fuses Usage 5 Engine Control Modul.
Fuses Usage 24 Fuel Injectors, Ignition Coils (Left Side) 25 Trailer Park Lamps 26 Driver Side Park Lamps 27 Passenger Side Park Lamps 28 Fog Lamps 29 Horn 30 Passenger Side High-Beam Headlamp 31 Dayt.
J-Case Fuses Usage 62 Starter 63 Stud 2 (Trailer Brakes) 64 Left Bussed Electrical Center 1 65 Electric Running Boards 66 Heated Windshield Washer System 67 Transfer Case 68 Stud 1 (Trailer Connector .
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7-13 for more information.
✍ NOTES 6-114.
Maintenance Schedule ..................................... .7-2 Introduction .................................................. .7-2 Maintenance Requirements ............................. .7-2 Your Vehicle and the Environment ................... .7-2 Using the Maintenance Schedule .
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements the vehicle warranties. See the Warranty and Owner Assistance booklet or your dealer/retailer for details.
Using the Maintenance Schedule We want to help keep this vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather.
Owner Checks and Services on page 7-10 tells what should be checked, when to check it, and what can easily be done to help keep the vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 7-13 and Maintenance Replacement Parts on page 7-15 .
When the CHANGE ENGINE OIL SOON message appears, the following services, checks, and inspections are required: ❑ Change engine oil and filter. See Engine Oil on page 6-15 . Reset oil life system. See Engine Oil Life System on page 6-18 . An Emission Control Service.
Additional Required Services The following services should be performed at the first maintenance service after the indicated miles (kilometers) shown for each item.
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Change transfer case fluid (severe service). See footnotes (m) and (n). ••• Change transfer case fluid (normal service).
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life.
(f) Lubricate all key lock cylinders, hood latch assembly, secondary latch, pivots, spring anchor, release pawl, rear compartment hinges, outer tailgate handle pivot points, latch bolt, fuel door hinge, and folding seat hardware. More frequent lubrication may be required when exposed to a corrosive environment.
Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure vehicle safety, dependability, and emission control performance. Your dealer/retailer can assist with these checks and services. Be sure any necessary repairs are completed at once.
At Least Once a Year Starter Switch Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. • The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). • The ignition key should come out only in LOCK/OFF.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine Oil The engine requires a special engine oil meeting GM Standard GM4718M.
Usage Fluid/Lubricant Front and Rear Axle SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677, in Canada 89021678) meeting GM Specification 9986115. Transfer Case DEXRON ® -VI Automatic Transmission Fluid. Hood Hinges Multi-Purpose Lubricant, Superlube (GM Part No.
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Maintenance Replacement Parts Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 15908916 A3086C Oil Filter 89017524 PF48 Spark Plugs 12609877 41-985 Wiper Blades Front – 21.
Engine Drive Belt Routing If your vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. 7-16.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 7-2 . Any additional information from Owner Checks and Services on page 7-10 can be added on the following record pages.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-18.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-19.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-20.
Customer Assistance and Information .............. .8-2 Customer Satisfaction Procedure ..................... .8-2 Online Owner Center ..................................... .8-5 Customer Assistance for Text Telephone (TTY) Users ......................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Cadillac. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments.
STEP THREE (U.S. Owners): Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However, if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two, you can file with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
STEP THREE (Canadian Owners): General Motors Participation in the Mediation/ Arbitration Program In the event that you do not feel your concerns have been addressed after the following the procedure outlined in Steps One and Two.
Online Owner Center Online Owner Center (U.S.) — www.gmownercenter.com/cadillac Information and services customized for your specific vehicle — all in one convenient place.
Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Cadillac has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Cadillac by dialing: 1-800-833-CMCC (2622).
GM Mobility Reimbursement Program This program, available to qualified applicants, can reimburse you up to $1,000 of the cost of eligible aftermarket adaptive equipment required for your vehicle, such as hand controls or a wheelchair/scooter lift. The offer is available for a very limited period of time from the date of vehicle purchase/lease.
Coverage Services are provided up to 5 years/100,000 miles (160 000 km), whichever comes first. In the U.S., anyone driving the vehicle is covered. In Canada, a person driving the vehicle without permission from the owner is not covered. Roadside Assistance is not a part of the New Vehicle Limited Warranty.
Cadillac Technician Roadside Service (U.S. only) Cadillac’s exceptional Roadside Service is more than an auto club or towing service. It provides every Cadillac owner in the United States with the advantage of contacting a Cadillac advisor and, where available, a Cadillac trained dealer technician who can provide on-site service.
Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/retailer can help minimize your inconvenience.
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options.
Additional Program Information All program options, such as shuttle service, may not be available at every dealer. Please contact your dealer for specific information about availability. All Courtesy Transportation arrangements will be administered by appropriate dealer personnel.
Repair Facility GM also recommends that you choose a collision repair facility that meets your needs before you ever need collision repairs. Your GM dealer/retailer may have a collision repair center .
Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there.
Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, notify Transport Canada immediately, in addition to notifying General Motors of Canada Limited.
Current and Past Model Order Forms Technical Service Bulletins and Manuals are available for current and past model GM vehicles. To request an order form, specify year and model name of the vehicle. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc.
Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
OnStar ® If your vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar Terms and Conditions for information on data collection and use.
A Accessories and Modifications ............................ 6 - 3 Accessory Power ............................................ 2-26 Accessory Power Outlets ................................. 3-25 Additional Required Services, Scheduled Maintenance ..
Appearance Care (cont.) Weatherstrips ............................................ 6-100 Windshield, Backglass, and Wiper Blades ...... 6-102 Wood Panels ............................................ 6-100 Ashtray ......................................
Bulb Replacement ........................................... 6-53 Back-Up Lamps - Ambulance Body ................ 6-51 F o g L a m p s ................................................. 3-22 Headlamp Aiming ........................................ 6-48 Headlamps .
Cleaning (cont.) Weatherstrips ............................................ 6-100 Windshield, Backglass, and Wiper Blades ...... 6-102 Wood Panels ............................................ 6-100 Climate Control System Outlet Adjustment ............
Drive Systems All-Wheel Drive ........................................... 6-45 Driver Information Center (DIC) ......................... 3-47 DIC Operation and Displays .......................... 3-48 DIC V ehicle Customization .......................
Engine (cont.) Cooling System ........................................... 6-24 Drive Belt Routing ....................................... 7-16 Exhaust ..................................................... 2-38 Fan Noise ...............................
G Gages Engine Coolant T emperature ......................... 3-41 Fuel .......................................................... 3-46 Speedometer .............................................. 3-35 T achometer .......................................
Hood Checking Things Under ................................ 6-12 Release ..................................................... 6-13 H o r n ............................................................... 3 - 6 How to Wear Safety Belts Properly .......
Lights (cont.) Flash-to-Pass ............................................... 3 - 9 F o g L a m p s ................................................. 3-45 Highbeam On ............................................. 3-46 High/Low Beam Changer ............
Mirrors (cont.) Outside Heated Mirrors ................................ 2-42 Outside Power Foldaway Mirrors .................... 2-40 P a r k T i l t ..................................................... 2-41 N Navigation Getting Started .............
Parking Assist ........................................................ 2-42 Brake ........................................................ 2-34 Over Things That Burn ................................. 2-38 Passenger Airbag Status Indicator ...........
Rearview Mirrors (cont.) Reclining Seatbacks, Power ............................... 1 - 8 Recommended Fluids and Lubricants ................. 7-13 Recovery Hooks ............................................. 5-32 Recreational V ehicle T owing ........
Seats (cont.) Head Restraints ............................................ 1 - 2 Heated and Cooled Seats .............................. 1 - 6 Heated Seats ............................................... 1 - 5 Heated Seats - Rear ......................
Storage Areas Center Console ........................................... 2-63 Cupholders ................................................. 2-62 Glove Box .................................................. 2-62 Luggage Carrier .........................
T o w / H a u l M o d e ............................................... 2-33 T ow/Haul Mode Light ....................................... 3-46 T owing Recreational V ehicle ..................................... 5-40 T owing a Trailer .................
W W arning Lights, Gages, and Indicators ............... 3-33 W arnings DIC W arnings and Messages ........................ 3-56 Hazard Flashers ............................................ 3 - 6 Safety and Symbols ....................................
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cadillac 2009 Escalade è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cadillac 2009 Escalade - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cadillac 2009 Escalade imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cadillac 2009 Escalade ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cadillac 2009 Escalade, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cadillac 2009 Escalade.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cadillac 2009 Escalade. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cadillac 2009 Escalade insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
