Manuale d’uso / di manutenzione del prodotto SLCA-7 del fabbricante Bunn
Vai alla pagina of 24
SLCA-7 INST ALLA TION & OPERA TING MANU AL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the lates.
2 39328.3 070913 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor .
3 INTRODUCTION This equipment dispenses hot beverages or soups on demand from powdered product. It is indoor use only on a sturdy counter or shelf. T ABLE OF CONTENTS Introduction .......................................................................
4 As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes.
5 INITIAL SET -UP 1. Apply the four non-skid pads from the parts box to the bottom of the legs. 2. Remove the drip tray assembly and drip tray bracket from the parts box. 3. Place a set of key holes in the drip tray bracket over the lower two screws in the panel below the hopper ac- cess door; push down gently and tighten screws.
6 OPERA TING CONTROLS AND INTERF ACE 1. Cup Size Buttons: Momentarily pushed to select beverage size to dispense. 2. Stop Button: Momentary pushed to stop dispensing. 3. Decaf Button: Momentarily pushed to select Decaffeinated coffee. 4. Dispense Buttons: Momentarily pushed to dispense selected beverage.
7 10 11 8 9 STOP MOCH A LA TTE ESPRESSO DECAF CAPPUCCINO MOCHA CAPPUCCINO HOT CHOCOL AT E BLACK COFFEE LA TTE SMALL LARGE 5 3 1 2 6 1 4 OPERA TING CONTROLS (Continued) 39328.
8 INST ALLING PUMP TUBING 1. Loosen the thumbscrews securing the tubing retainer plates to the pump bodies and set the retainer plates aside. 2. Depress the tension screws and remove them from the notch in the pump body , releasing the spring tension on the pump bands.
9 INITIAL FILL & HEA T 1. T urn on the water supply and connect the dispenser to the power sour ce. 2. Water will automatically flow into the tank to the proper level and then shut-off.
10 SLCA-7 PROGRAMMING LED DISPLA Y PROGRAM MODE DESCRIPTION Program Mode: Used to change or enter new set-up values. T o enter the Program Mode , Set the RUN/NIGHT/PROGRAM Switch to the PROGRAM position, the unit will display “__PPP” to indicate it is in the Program Mode.
11 PROGRAMMING (Continued) LED DISPLA Y PROGRAM MODE DESCRIPTION MENU (-) (+) 6 0 3 0 MENU (-) (+) 7 0 3 0 MENU (-) (+) 8 0 1 0 MENU (-) (+) 9 0 1 0 MENU (-) (+) 0 1 4 5 0 MENU (-) (+) 1 1 1 0 MENU (-) (+) 2 1 1 0 5.
12 PROGRAMMING (Continued) LED DISPLA Y PROGRAM MODE DESCRIPTION MENU (-) (+) 3 1 8 MENU (-) (+) 4 1 5 MENU (-) (+) 5 1 2 4 MENU (-) (+) 6 1 1 MENU (-) (+) 7 1 # MENU (-) (+) 8 1 0 4.
13 PRIMING THE CONCENTRA TE LINES 1. Open the dispenser door . 2. Select Prime on the Function Selector Switch and Run on the Mode Selector Switch. 3. Close the dispenser door .
14 DRAINING THE HOT WA TER T ANK CAUTION - The dispenser must be disconnected from the power source throughout these steps 1. Disconnect the dispenser from the power source. 2. Open front door and place Main Power Switch in the OFF position and let the water in the tank cool before draining.
15 CLEANING & PREVENT A TIVE MAINTENANCE General Cleaning and Sanitizing Procedures Note: The BUNN¨ SLCA-7 dispenser incorporates a “user select- able” rinse reminder feature, which flashes the LED’ s on the front panel when it is time to rinse.
16 Weekly: Parts W ashing and Sanitizing 39328.3 012113 14. When reassem- bling parts, be sure to align arrow on frother disk with flat on whipper mo- tor shaft, and rotate tab on whipper base clock wise to the vertical position to lock mixing cham- ber .
17 REPLACING THE PUMP TUBING The pumps and tubing used in the dispenser are designed to give maximum performance and long life. However , the tubes are a wear item and must be replaced periodically . How long the tube last is dependent on usage and properties of the concentrate.
18 MENU (-) (+) CALIBRA TING THE DISPENSER CALIBRA TION MODE: The SLCA-7 is calibrated at the factory and does not normally need to be re-calibrated. T o enter the Calibration Mode , Set the RUN/NIGHT/PROGRAM Switch to the PROGRAM position and then hold the MENU switch down for 10 seconds.
19 LED DISPLA Y CALIBRA TION MODE DESCRIPTION MENU (-) (+) 4 C r u n MENU (-) (+) 4 C MENU (-) (+) 5 C E 0 0 MENU (-) (+) 6 C - - MENU (-) (+) P C 0 X X CALIBRA TING THE DISPENSER (Continued) - Right .
20 TROUBLESHOOTING GUIDE Error Codes When an error has occurred, all Door LED’ s will be flashing. Open the Door to access the LED Display and re- cord the Error Code.
21 Field Calibration of the Concentrate Pumps, Dispenser Flow Rates, and Hopper Powder Throw The factory set default values for the Pump & Dispenser Flow Rates are ver y accurate and typically do not need to be field calibrated.
22 Calibrating the Dispenser Flow Rates Decaf Coffee - Dispenser Flow Rate Calibration 1. Select RINSE on the Function Selector Switch, and PROGRAM of the Mode Selector Switch. Depress and Hold the MENU switch for approximately 10 sec. The unit will display “C1 run” when it has entered the Cali- bration Mode 2.
23 9. Install the coffee BIB’ s into the unit, and prime the pumps. Dispense several cups of both regular coffee and Decaf coffee. If either one or both the DECAF and HOT CHOCOLA TE LED illuminates during this process and dispensing is disabled, the EMPTY PRODUCT WARNING can be reset by priming the appropriate pump momentarily .
24 ELECTRICAL WIRING DIAGRAM SLCA-7 39328.3 012113 1 5 8 1 5 10 15 20 1 5 10 14 1 5 10 12 5 1 1 5 +V +V -V -V GROUND N/L2 L1 COM N.O. MAIN CONTROL BOARD J15 J3 J1 1 J6 J5 J11 J4 10 1 5 MENU (-) (+) J1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Bunn SLCA-7 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Bunn SLCA-7 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Bunn SLCA-7 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Bunn SLCA-7 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Bunn SLCA-7, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Bunn SLCA-7.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Bunn SLCA-7. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Bunn SLCA-7 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
