Manuale d’uso / di manutenzione del prodotto BCO4016IM del fabbricante BTC
Vai alla pagina of 22
Combo Drive CD-R 40X/CD-RW 12X/DVD 16X User’s Manual.
CLASS 1 LA SER PRODUCT APPA REIL A LA SER DE CLASSE 1 LASER KLA SSE 1 LUOKAN 1 LA SERLAITE PRODUIT LASER CATEGORIE 1 DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN A TTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE.
FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Table of Contents INTRODUCTION 1 F EATURES 1 S YSTEM R EQUIREMENTS 2 P ACKAGE C ONTENTS 2 INSTALLATION 3 H OST I NTERFACE C ONNECTIONS 3 H ARDWARE I NSTALLATION 4 D RIVER I NSTALLATION 5 S OFTWARE D E.
COMBO DRIVE 1 INTRODUCTION Features Welcome to a multimedia world of CD-ReWritable technology and DVD-ROM capabilities. This high-performance combo drive combines CD-RW and DVD- ROM in one single drive which frees up precious bay space and presents you abundant function.
COMBO DRIVE System Requirements For IBM compatible PCs, the sy stem requirements recommended are as follows: ♦ PC sufficient to run Windows 95/98/Me or WindowsNT/2000/XP ♦ Pentium II 300MHz above with at least 64MB of memory ♦ Fast and sufficient hard disk space (minimum 150MB for installation, 1GB or more is recommended.
COMBO DRIVE 3 INSTALLATION Host Interface Connections Most current mainboard models have two IDE ports (primary and secondary) which can connect two IDE cables. Two IDE cables allow you to connect up to four devices , but it is recommended that you separate IDE ports for your hard driv e and your Combo drive.
COMBO DRIVE MAST ER CSEL SLAVE JUMPER Improper or conflicting setting will cause the unit not be detected by your system. Hardware Installation 1. Turn off the power to your computer system and all peripheral devices. 2. Disconnect all cables and connectors from the back of your computer, and then remove the cover from the computer.
COMBO DRIVE 5. If you have a sound card that can be connected to this drive, you can also connect the drive (as Audio-Out) and the sound card (as Audio-in) with a 4-pin audio cable. If your mainboad is integrated with built-in sound system, plug the 4-pin audio cable into the CD-IN connector on the mainboard as Audio-in.
COMBO DRIVE 6 Software Description Burning Software The bundled mastering software gives you the complete solution for making audio/data CDs right from your desktop. It allows you to copy files from your computer to a reco rdable compact disc. In addition, the audio CDs you create can be played in your home or car CD player.
COMBO DRIVE 7 systems with DVD-Video capability. You can only play DVD-Video discs with the same region code as your DVD-Video Playback system. As for DVD-ROM drives, one kind of the DVD-Video Playback system, there are 2 types: RPC Phase 1 (as RPC1) : RPC1 drives do not have built-in hardware support for region management.
COMBO DRIVE 8 OPERATION & CONNECTION Front Panel 1. Headphone Jack By plugging in the stereo mini jack here, you can listen to an audio disc directly playing from the drive with headphones. 2. Headphone Volume Control This rotary knob adjusts the volume level of the headphone output.
COMBO DRIVE 4. Disc Tray This is the tray for the disc. Plac e the disc in the tray, then press the Close/Eject button or gently push the tray to close it. 5. Emergency Eject Hole When the Eject/Close button can’t wo rk properly and the disc tray can’t be opened, you can insert a paper clip or other small rod into this hole for manual ejection.
COMBO DRIVE 10 2. Analog Audio Output Connector This connector allows you to connect the drive to your sound card with a 4-pin audio cable. 3. Device Configuration Jumper Set the jumper to Master, Slave or Cable Select according to your system configuration.
COMBO DRIVE 11 TECHNICAL DATA Performance Transfer rate Read: CD: 6000kb/sec (up to 40X) DVD: 21632kb/sec (up to 16X) Write: CD-R: 6000kb/sec (up to 40X) CD-RW: 1800kb/sec (up to 12X) Data buffer 2MB .
COMBO DRIVE 12 Compact Disc Disc Size 80mm and 120mm discs Disc Data Capacity DVD-ROM: Single layer – 4.7GB Dual layer – 8.5GB (one side) CD-ROM: 74min – 650MB – Mode 1 80min – 700MB – Mod.
COMBO DRIVE 13 TROUBLESHOOTING To help you get more familiar with t he Combo Drive, the following FAQ lists some common problems you might encounter. Please read it for reference before you request RMA support from your dealer. Q1. The drive cannot be recognized.
COMBO DRIVE 14 (2) Check both rear side of the drive and sound card on M/B (If Audio chipset is on board). If they are well connect ed, check if the sound card is working. Q5. The drive can’t read former session(s) of the CD-R disc w hich has been w ritten tw ice or more times.
COMBO DRIVE 15 (1) Use the burning software which is provided by original supplier and bundled with this Combo Drive or download the updated file from internet. (2) More capacity of hard disk is needed if using hard disk as temporary buffer. (3) Place the disc correctly.
COMBO DRIVE 16 Yes, it does support CD-Text & SAO f unction and you may edit the title or content into your music CD..
.
3100550910 Version 1.1 Jan. 2003.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il BTC BCO4016IM è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del BTC BCO4016IM - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso BTC BCO4016IM imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul BTC BCO4016IM ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il BTC BCO4016IM, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del BTC BCO4016IM.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il BTC BCO4016IM. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo BTC BCO4016IM insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
