Manuale d’uso / di manutenzione del prodotto AH-FS151250D del fabbricante Bryan Boilers
Vai alla pagina of 17
Form 2143 Date: 4/3/03 Repl: 2/1/99 BR Y AN STEAM LLC Inst allation and Operating Service Manual BOILER FEED SYSTEM 0.
INSTALLATION AND OPERAT ION SERVICE MANUAL BOILER FEED SYSTEM Bryan Steam LLC 783 North Chili Avenue * Peru, IN 46970 Phone 765.473.6651 • Fax 765.473.
MODEL IDENTIFICATION & DESIGNATION Boiler F eed System A – H - FS – 15 – 12 – 50 – D A = LINING BLANK – NO LINING A – APEXIOR LINING B – GALVANIZED LINING H = TANK POSITION H – H.
T a ble of Contents SECTION 1 – INSTALLATION INSTRUCTIONS 1.1 FOUNDAT ION ......................................................................................................... 1 1.2 CLE ARANCE ....................................................
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 1 Sectio n 1 Installa tion Instr uctions – Boiler F eed System Note: Please read the entire instruction manual before attempting installation. Insurance and local or state regulatory codes may contain additional or more stringent requirements than those contained in this manual.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 2 feed system near its permanent location. Before in stallation, take inventory of items that were shipped loose so they will not be misplaced. 1.4 BOILER FEED SY STEM CONNECTIONS 1.4.1 GENERAL Maintain clearances as shown on the dimensional drawing for servicing and as referenced in N.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 3 1.4.5 OVERFLOW CONNECTION The overflow connection should be piped to an approved drain for gravity flow of any water that may reach that level in the tank. The purpose of the overflow connection is to keep the tank from being flooded in case a high level condition occurs in the unit.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 4 1.5.2 MAKE UP FILL VALVE A self-contained mechanical float type make up water control is proved to accept incoming water up to a differential pressure of 70 psi (see manufacturer’s date for exact pressures).
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 5 1.6 PR OCEDURE T O BE FOLL O WED BEFORE PLA CING BOILER FEED SY STEM IN OPERA TION 1.6.1 CLEANING THE FEED SYSTEM After installation is complete, the feed system should be checked for debris. Any debris found in the tank, pump, or strainers should be removed before start-up.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 6 Sectio n 2 ST AR T -UP AND OPERA TION – BOILER FEED SY STEM WARNING: IMPROPER SERVICING AND START-UP OF THIS EQUIPMENT MAY CREATE A POTENTIAL HAZARD TO EQUIPMENT AND TO OPERATORS OR PERSONS IN THE BUILDING.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 7 2.1.2 ATMOSPHERIC TANK DESIGN This tank was designed to be used only in atmospheric conditions. To avoid potential hazards, this tank should never be pressurized. Safety precautions should be taken to make sure the tank is never pressurized.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 8 2.2 OPERA TING INSTRUCTIONS CAUTION: Check all electrical terminals and piping connections for tightness before start-up.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 9 Sectio n 3 CARE AND MAINTENANCE BOILER FEED SY STEMS 3.1 REQUIRED PRECA UTIONS DURING TEMPORAR Y USE 3.1.1 GENERAL A boiler system is often utilized in new construction to assist in curing of building components or to provide temporary heat or for other purposes.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 10 6. Considerations of warranty should the boiler system be used for temporary heat without adherence to the recommended start-up and operating procedures outlined in the instruction manuals.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 11 FILTRATION For some old systems, there is a reluctance to clean the piping because of the possibility of leaks occurring in badly corroded lines. Should the customer refuse cleaning, it is necessary to install filtration equipment.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 12 3.6 SUGGESTED MAINTENANCE SCHEDULE DAILY Make visual inspection of gauges, monitors, and indicators and record readings in boiler system log. Make visual check of instrument and equipment settings against factory recommended specifications.
BOILER FEED SYSTEM DATE: 4/3/03 REP:2/1/99 13 Idle boilers are vulnerable to attack when air contacts untreated wet metal surfaces. To prevent corrosion, the metal must be protected by either keeping the surfaces completely dry or by excluding air from the system.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Bryan Boilers AH-FS151250D è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Bryan Boilers AH-FS151250D - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Bryan Boilers AH-FS151250D imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Bryan Boilers AH-FS151250D ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Bryan Boilers AH-FS151250D, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Bryan Boilers AH-FS151250D.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Bryan Boilers AH-FS151250D. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Bryan Boilers AH-FS151250D insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.