Manuale d’uso / di manutenzione del prodotto S50X del fabbricante Briggs & Stratton
Vai alla pagina of 52
This manual is a vailab le in Spanish. For a cop y , contact y our Snapper Pr o dealer or www .snapperpr o.com. Este manual está disponible en Español. P ara obtener una copia, póngase en contacto con su distribuidor Snapper Pr o o www.snapperpr o.
WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Briggs & Stratton Power Products Group, LLC. Copyright © 2012 Briggs & Stratton Corporation Milwaukee, WI, USA.
Table of Contents 1 Operator Safety ...........................................................2 Safety Rules and Information .................................2 Safety Decals ..........................................................8 Safety Interlock System .
2 Operator Safety Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Do not operate this machine unless you have been trained.
3 Operator Safety Slope Operation Operation on slopes can be dangerous. Using the unit on a slope that is too steep where you do not have adequate wheel traction (and control) can cause sliding, loss of steering, control, and possible rollover. You should not operate on a slope greater than a 5.
4 Fuel and Maintenance Always disengage all drives, shutoff the engine, and remove the key before doing any cleaning, refueling, or servicing. Gasoline and its vapors are extremely flammable. Do not smoke while operating or refueling. Do not add fuel while engine is hot or running.
5 2. Mow only in the daylight or with good artificial light, keeping away from holes and hidden hazards. 3. Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’s position. Use seat belts if provided.
6 Operator Safety 25. OSHA regulations may require the use of hearing protection when exposed to sound levels greater than 85 dBA for an 8 hour time period. Slope Operation Slopes are a major factor related to loss-of-control and tip- over accidents, which can result in severe injury or death.
7 Operator Safety Service and Maintenance To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
8 www.SnapperPro.com Operator Safety Safety Decals Before operating your unit, read the safety decals. The cautions and warnings are for your safety. To avoid a personal injury or damage to the unit, understand and follow all safety decals. 1 2 2 3 3 1 2 3 4 (Located by transmissions).
9 Operator Safety Safety Interlock System This unit is equipped with safety interlock switches. These safety systems are present for your safety, do not attempt to bypass safety switches, and never tamper with safety devices. Check their operation regularly.
10 www.SnapperPro.com Features and Controls Identification Numbers SAMPLE SAMPLE When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers. Record your part number, serial number and engine serial numbers in the space provided on the inside front cover for easy access.
11 Control Functions The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.
12 www.SnapperPro.com Transmission Oil Fill This unit is equipped with two transmission oil reservoirs. The transmission oil reservoirs are located beneath the operator’s seat and in front of the engine. Transmission oil is added through the transmission oil reservoirs.
13 General Operating Safety Before first time operation: • Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower. • Become familiar with all of the controls and how to stop the unit.
14 www.SnapperPro.com Operation Figure 5. Seat Adjustment A. Seat Adjustment Lever Seat Adjustment See Figure 5. The seat can be adjusted forward and backward. Move the lever towards the left, position the seat as desired, and release the lever to lock the seat into position.
15 Operation Foot Pedal Adjustment The deck lift foot pedal can be adjusted to accommodate the operator’s height for optimal comfort. To adjust pedal position: 1. Remove the foot pedal (A, Figure 7) from the pedal mount tab (B). 2. Remove the pedal mount hardware (C) and rotate the tab 180 degrees.
16 www.SnapperPro.com Starting the Engine 1. While sitting in the operator’s seat, engage the parking brake by pulling the parking brake lever up, make sure the PTO switch is disengaged (pressed down fully) and the ground speed control levers are locked in the NEUTRAL position.
17 Operation Zero Turn Driving Practice The lever controls of the Zero Turn rider are responsive, and learning to gain a smooth and efficient control of the rider’s forward, reverse, and turning movements will take some practice.
18 www.SnapperPro.com Executing an End-Of-Row Zero Turn Your Zero Turn Rider’s unique ability to turn in place allows you to turn around at the end of a cutting row rather than having to stop and Y-turn before starting a new row. For example, to execute a left end-of row zero turn: 1.
19 Operation Mowing 1. Engage the parking brake. Make sure the PTO switch is disengaged, the ground speed control levers are locked in the NEUTRAL position and the operator is on the seat. 2. Start the engine (see Starting The Engine ). 3. Set the mower cutting height (see Mowing Height Adjustment ).
20 www.SnapperPro.com When and How Often to Mow The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: 1. Mow when the grass is between three and five inches high.
21 Operation Attaching A Trailer The maximum weight of a towed trailer should be less than 200 lbs (91kg). Secure the trailer with a appropriately sized clevis pin (A, Figure 18) and clip (B). Excessive towed loads can cause loss of traction and loss of control on slopes.
22 www.SnapperPro.com Maintenance Schedule The following schedule should be followed for normal care of your rider and mower. You will need to keep a record of your operating time. Determining operating time is easily accomplished by observing the elapsed time recorded by the hour meter.
23 Regular Maintenance Checking / Adding Fuel To add fuel: 1. Remove the fuel cap. 2. Fill the tank to about 1-1/2” (3,81 cm) of the bottom of the filler neck. This will allow for fuel expansion. NOTE: Do not overfill. Refer to your engine manual for specific fuel recommendations.
24 www.SnapperPro.com Lubrication Lubricate the unit at the locations shown in Figures 20 through 23 as well as the following lubrication points. Grease: • front caster wheel axles & yokes • deck lift pivot blocks • mower deck spindles • mower deck idler arm Use grease fittings when present.
25 Regular Maintenance Figure 24. Checking Transmission Oil Level A. Transmission Oil Reservoirs B. “FULL COLD” mark A B Check / Fill Transmission Oil Oil Type: 20W-50 conventional detergent motor oil. 1. Check the oil level when the unit is cold.
26 www.SnapperPro.com Regular Maintenance Servicing The Mower Blades Removing the Mower Blade 1. To remove the mower blade, use a 1” wrench on the flats of the spindle shaft and remove the mower blade mounting bolt with a 15/16” wrench (Figure 26).
27 Regular Maintenance Figure 31. Tightening the Mower Blade for Installation A. Mower Blade Mounting Bolt B. Flat Washer C. Mower Blade Air Lift (Points Up For Installation) D. 4 X 4 Wooden Block D A B Sharpening the Mower Blade 1. Sharpen the mower blades with grinder, hand file, or electric blade sharpener.
28 www.SnapperPro.com Figure 32. Control Lever Adjustment A. Placement Hardware B. Ground Speed Control Lever WARNING DO NOT adjust the tractor for a faster overall speed forward or reverse than it was designed for. A B Figure 33. Top Speed Adjustment A.
29 Regular Maintenance Figure 34. Parking Brake Adjustment A. Brake Spring B. First Measurement - .50” (1,27 cm) C. Brake Spring Rod D. Lock Nut E. Second Measurement - .375” (0,95 cm) F. Set Collar G. Brake Shaft Weldment A B E G C D F Parking Brake Adjustment 1.
Return-to-Neutral Adjustment To determine if it is necessary to adjust the neutral return, perform the following steps. 1. Disengage the PTO, engage the parking brake and turn off the engine. 2. Move the ground speed control levers into the operating position, pull the levers rearward and release.
31 Regular Maintenance Figure 36. Check Lift Rod Timing Figure 37. Adjust Lift Rod Timing Figure 38. 2 x 4 Locations Deck Rod Timing Adjustment 1. Park the machine on a flat, level surface. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.
32 www.SnapperPro.com Regular Maintenance Figure 39. Hanger Chain Adjustment 36” Models 48” Models Deck Leveling Adjustment NOTE: Before adjusting the deck level, the deck lift rod timing must be checked and/or adjusted. 1. Park the machine on a flat, level surface.
33 Regular Maintenance Mower Belt Replacement 1. Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key. 2. Lower the mower deck to its lowest cutting position and remove the mower deck guards.
34 www.SnapperPro.com Regular Maintenance Check the Mower Belt Idler Tensioner Spring Length This procedure is for models with 36” Mower Decks (Serial Number Range: All) and models with 48” Mower Decks (Serial Number Range: 2014732448 & Above) 1.
35 Regular Maintenance 5-7/8” (14.92 cm) Figure 43. Hydraulic Pump Drive Belt Replacement A. Pump Drive Belt B. Crankshaft Pulley C. Pump Pulley D. Idler Pulley E. Idler Arm F. Spring G. Spring Anchor Eyebolt H. Stationary Idler Pulley B D A C H C Hydraulic Pump Drive Belt Replacement 1.
36 www.SnapperPro.com Regular Maintenance Figure 44. Battery Compartment A. Positive (+) Cable & Terminal B. Negative (-) Cable & Terminal Battery Maintenance NOTE: This unit is equipped with a maintenance-free BCIU1 battery. Cleaning the Battery and Cables 1.
37 Regular Maintenance Battery Service Checking Battery Voltage A voltmeter can be used to determine condition of battery. When engine is off, the voltmeter shows battery voltage, which should be 12 volts. When engine is running, the voltmeter shows voltage of charging circuit which normally is 13 to 14 volts.
38 www.SnapperPro.com Regular Maintenance To Starter Switch Starting V ehicle Battery T o Gr ound To Starter Switch Dischar ged V ehicle Battery Engine Block THIS HOOK-UP FOR NEGA TIVE GR OUND VEHICLE.
39 Regular Maintenance Storage Temporary Storage (30 Days Or Less) Remember, the fuel tank will still contain some gasoline, so never store the unit indoors or in any other area where fuel vapor could travel to any ignition source. Fuel vapor is also toxic if inhaled, so never store the unit in any structure used for human or animal habitation.
40 www.SnapperPro.com Troubleshooting Chart While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and remedies.
41 Troubleshooting Rider Troubleshooting Continued. Problem Cause Remedy Engine runs, but rider will 1. Transmission release lever(s) 1. Move the transmission release lever(s) to not drive. in “open” position. the “closed” position. 2. Belt is broken.
42 www.SnapperPro.com Troubleshooting TROUBLESHOOTING COMMON CUTTING PROBLEMS PROBLEM CAUSE REMEDY Streaking 1. Blades are not sharp. 2. Blades are worn down too far. 3. Engine speed is too slow. 4. Ground speed is too fast. 5. Deck is plugged with grass.
43 Specifications Specifications Note: Specifications are correct at time of printing and are subject to change without notice. ENGINE 19 Gross HP† Kawasaki (Models: 5900769, 5900853 and 5900734) Make Kawasaki Model FH580V Displacement 35.7 Cu. in (585 cc) Electrical System 12 Volt Starter, 13 amp.
44 www.SnapperPro.com THIS IS A 15 DEGREE SLOPE INSTRUCTIONS 1. Fold this page along the dotted line indicated above. 2. Align the left edg e of this guide with a vertical tree , a power line pole, a fence post, or any vertical structure. 3. Compare the angle of the fold with the angle of the hill.
Notes Not for Reproduction.
Notes Not for Reproduction.
Not for Reproduction.
BRIGGS & STRA TTON PRODUC TS W ARRANTY POLIC Y September 2012 LIMITED W ARRANTY Briggs & Stratton warr ants that, during the warr anty period specified below , it will repair or replace, fr ee of charge, an y par t that is defective in material or w orkmanship or both.
California, U.S. EP A, and Briggs & Stratton Corporation Emissions Control W arranty Statement Y our Warranty Rights A nd Obligations September 2012 The California Air Resources Board, U.S. EP A, and Briggs & Stratton (B&S) are pleased to explain the emissions control system warranty on your Model Y ear 2012 - - 2013 engine/ equipment.
Operator’ s Manual S50X/S50XT Series Zer o- T urn Riding Mow ers BRIGGS & STRATTON POWER PRODUCTS GROUP , LLC 5375 NORTH MAIN STREET MUNNSVILLE, NY 13409 800 933 6175 Not for Reproduction.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Briggs & Stratton S50X è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Briggs & Stratton S50X - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Briggs & Stratton S50X imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Briggs & Stratton S50X ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Briggs & Stratton S50X, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Briggs & Stratton S50X.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Briggs & Stratton S50X. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Briggs & Stratton S50X insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
