Manuale d’uso / di manutenzione del prodotto LT-200 del fabbricante Briggs & Stratton
Vai alla pagina of 14
1/2006 1 TP 300-4517-00-RG-SMAN Setup & Adjustment Instructions L T -200 Series T ractors and Mowers T ABLE OF CONTENTS: SAFETY RULES .................................................................2 SETUP PROCEDURES Quick Setup List ............
L T -200 Series TP 300-4517-00-RG-N 3/2007 2 Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of equipment, severe personal injury or death to you, yourself or bystanders, or damage to property or equipment.
L T -200 Series 3/2007 3 TP 300-4517-00-RG-N Quick Setup List - P age Setup Procedure Steps to P erform 4 Uncrating o Remov e Crate & Banding. o Place T ransmission Release Le ver in PUSH position & Roll T ractor f orward off skid.
L T -200 Series TP 300-4517-00-RG-N 3/2007 4 Uncrating Using a reciprocating utility saw or equivalent, cut crate away from bottom skid. Remove crate. Remove shrink- wrap plastic. 2. Cut banding from front and rear tractor axles. Cut banding from mower rollers.
L T -200 Series 3/2007 5 TP 300-4517-00-RG-N Chec k Fluid Levels Check T ransmission Oil Level The K46 transmission is a sealed unit that is shipped with the correct oil level. However if a transmission’s oil level is suspect it can be checked. See Transmission Maintenance.
L T -200 Series TP 300-4517-00-RG-N 3/2007 6 Figure 4. Seat Switch A. Seat Switch B. Wiring Harness P erf orm Safety Chec ks Functional T ests 1. Check the tractor for loose bolts, screws, nuts, etc.
L T -200 Series 3/2007 7 TP 300-4517-00-RG-N Figure 5. Blade Torque A. 4x4 Wood Block B. Spline or Hex Washer C. Spring Washer D. Blade Bolt T or que Mower Blades 1. Secure the hex washer (B, Figure 5), spring washer (C) and capscew (D). Use a wooden block (A) to prevent blade rotation while tightening the blade bolt (D) to 45-55 ft.
L T -200 Series TP 300-4517-00-RG-N 3/2007 8 Lubrication Lubricate the unit at the locations shown in Figures 7-10 as well as the lubrication points listed. Generally, all moving metal parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys.
L T -200 Series 3/2007 9 TP 300-4517-00-RG-N Figure 8. Mower Lubrication Points Figure 10. Arbor Lubrication Point Figure 9. Mower Lubrication Points Hourmeter HOURMETER MODELS The hour meter measures the number of hours the key has been in the RUN position.
L T -200 Series TP 300-4517-00-RG-N 3/2007 10 Mower Dec k Remov al & Installation Removing the Mo wer Deck 1. Park tractor on a hard, level surface such as a concrete floor. Turn off PTO switch and engine, remove the key and apply parking brake. 2.
L T -200 Series 3/2007 11 TP 300-4517-00-RG-N Leveling The Mo wer If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as specified in Checking Tire Pressure.
L T -200 Series TP 300-4517-00-RG-N 3/2007 12 Gauge Wheels The mower gauge wheels can be placed in several positions depending on the height of cut. When using higher cutting heights, set the wheels in the lower position. When using lower cutting heights, set the wheels in the upper position.
L T -200 Series 3/2007 13 TP 300-4517-00-RG-N Electric PT O Clutch Adjustment Check the PTO clutch adjustment after 250 hours of operation. Also perform the following procedure if the clutch is slipping or will not engage.
L T -200 Series TP 300-4517-00-RG-N 3/2007 14 Mower Belt Replacement Note: It is not necessary to remove the mower to install a new belt. However, for easier access mower can be removed. See Mower Removal in the Operation section. 1. Park the tractor on a smooth, level surface such as a concrete floor.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Briggs & Stratton LT-200 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Briggs & Stratton LT-200 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Briggs & Stratton LT-200 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Briggs & Stratton LT-200 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Briggs & Stratton LT-200, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Briggs & Stratton LT-200.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Briggs & Stratton LT-200. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Briggs & Stratton LT-200 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
