Manuale d’uso / di manutenzione del prodotto 150Z Series del fabbricante Briggs & Stratton
Vai alla pagina of 38
OPERA T OR’S MANU AL 20HP Zero-T urn Riders Mfg. No. Description 2690715 Simplicity Axion, 20HP w/ 42” Mower (CE) 2690716 Snapper 150Z, 20HP w/ 42” Mow er (CE) 2690770 Simplicity Axion, 20HP w/42” Mow er (A UST) Axion / 150Z ZTR Series 1734212 Re vision 03 Re v .
.
1 T ABLE OF CONTENTS Safety Rules General Operation...................................................2 T ransportation & Storage ........................................2 Slope Operation ......................................................3 T o wed Equipment .
2 SAFETY R ULES GENERAL OPERA TION 1. Read, understand, and f ollow all instructions in the manual and on the unit bef ore star ting. 2. Do not put hands or f eet near rotating par ts or under the machine. K eep clear of the discharge opening at all times.
3 CHILDREN T ragic accidents can occur if the oper ator is not aler t to the presence of children. Children are often attracted to the unit and the mowing activity . Ne ver assume that children will remain where you last sa w them. 1. K eep children out of the mowing area and under the watchful care of another responsib le adult.
4 WARNING: To avoid serious injury, operate your unit up and down the face of slopes, never across the face. Do not operate on slopes greater than 10 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes.
5 SER VICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars , pipes, and other sources of ignition. 2. Use only approv ed gasoline containers. 3. Ne ver remo v e the gas cap or add fuel with the engine running. Allow the engine to cool before refueling.
6 This unit has been designed and manuf actured to provide y ou with the saf ety and reliability you w ould e xpect from an industr y leader in outdoor power equipment manuf acturing.
7 174xxxx Right Ground Speed Lever (Controls Right Drive Wheel) Forward Neutral Start / Park Reverse 174xxxx Left Ground Speed Lever (Controls Right Drive Wheel) Forward Neutral Start / Park Reverse 1733458 Low Cut 1 4 3 2 High Cut OPERA TION To Stop the Engine: 1.
8 IDENTIFICA TION NUMBERS ID T ag When contacting the service center for replacement parts, service, or inf ormation you MUST ha ve these numbers. Record your model name/n umber , manufacturer’ s identification numbers, and engine serial numbers in the space provided f or easy access.
9 OPERA TION Ground Speed Le ver s / P arking Brake These le vers control the g round speed and parking brake of the rider . The left lev er controls the left rear drive wheel and the right lev er controls the right rear drive wheel and parking brake .
10 Mower Cutting Height Switc h T o increase the mower cutting height (raise the mo wer deck), press the top of the y ellow cutting height s witch. T o decrease mower cutting height (low er the mower deck), press the bottom of the s witch. Mower cutting height range is appro ximately 3-3/4” to 1-1/2”.
11 W ARNING Never allo w passengers to ride on the unit. Before lea ving the operator’ s position for an y reason, engage the parking brake and disengage t h e P TO. N e ver leave the unit unattended (i.e. out of sight) with the engine running. T o reduce fire hazar d, keep the engine, rider and mower free of grass, leaves and excess grease.
12 PUSHING THE RIDER BY HAND NO TE: Do not disengage the transmissions if parked on a slope. 1. T ur n the mower b lades OFF , push the ground speed control le vers out to their ST AR T/P ARK positions, turn the ignition s witch OFF , remo ve the key , and w ait f or all moving parts to stop.
13 DRIVING PRA CTICE - B ASIC DRIVING W ARNING: Ne ver oper ate on slopes greater than 17.6% (10°). See SLOPE OPERA TION in the safety section. Zero turn r iders operate diff erently from other f our- wheeled vehicles . The dr ive wheels are also y our steering wheels.
14 AD V ANCED DRIVING Executing an End-Of-Ro w Zero T urn Y our zero turn rider’ s unique ability to tur n in place allows y ou to turn around at the end of a cutting row rather than ha ving to stop and make a Y -tur n before starting a new row . F or e xample, to e x ecute a right end-of row zero turn: 1.
15 MO WER DECK REMO V AL & INST ALLA TION NO TE: P erform mower remov al and installation on a hard, le vel surf ace such as a concrete floor . Removing the Mo wer Dec k 1. T ur n the mower b lades OFF , put the ground speed control le vers in ST AR T/P ARK position, tur n the ignition OFF , and w ait f or all moving par ts to stop .
16 MAINTENANCE MAINTENANCE SCHEDULE The f ollowing schedules should be f ollowed f or nor mal care of your rider and mow er . * More often in hot (ov er 85° F: 30° C) weather or dusty operating conditions . ** Check the function of the saf ety system after the unit has been stored for 30 da ys or longer .
17 Rider Maintenance Items A CCESSING THE ENGINE COMP AR TMENT Lift up on the back edge of the seat dec k to access the engine compar tment. CLEAN DEBRIS FR OM RIDER AND ENGINE COMP AR TMENT Service Interval: Bef ore each use. CA UTION: If debris is not remo ved from the engine compartment and other hot surfaces, it creates a fire hazard.
18 Figure 16. Arbor Lubrication (3-Blade Model Shown) Figure 17. Lubricating Rider Figure 18. Lubricating Rider Figure 15. Mower Lubrication LUBRICA TION Service Interval: 25 hours. Lubricate the unit at the locations shown in Figures 15 through 19 as well as the f ollowing lubrication points.
19 CLEAN DECK & CHECK / REPLA CE MO WER BLADES Service Interval: 25 hours or as required. 1. Remov e mow er deck (see “Mower Dec k Remov al” in the OPERA TION section). 2. See Figure 20. Remov e blade to inspect it or to saf ely access the underside of the mower dec k.
20 CLEAN THE B A TTER Y AND CABLES Service Interval: 100 Hours 1. Disconnect the cables from the battery , negative cable first (B , Figure 23). 2. Remov e the rubber strap securing the batter y , and remov e the battery . 3. Clean the batter y and batter y compar tment with a solution of baking soda and water .
21 CHECK / ADJUST PT O CLUTCH Service Interval: 200 Hours. The P ower T ake Off (PT O) clutch drives the mow er blades . The PTO clutch is engaged and disengaged b y the mower b lade switch. Check the PT O clutch adjustment e very 200 hours of operation.
22 Figure 26. Recommended Engine Oil - Briggs & Stratton Models Use oil classified API Service Class SF , SG, SH, SJ or better with SAE Viscosity: 100 80 60 40 20 32 0 -20 38 27 16 4 -7 0 -18 -30 ˚F ˚C 30 Conventional** Synthetic 5W-30, 10W -30 5W-30 10W-30 Conventional* *CAUTION: Air cooled engines run hotter than automotive engines.
23 SER VICE AIR FIL TER & PRE-CLEANER Service Interval: Pre-Cleaner : Every 25 hours or as required. Air Filter : Ev er y 50 hours or as required. Replacement Interval: Pre-Cleaner: As required. Air Filter : Every 200 hours or once per season. Air Filter Remov al & Installation 1.
24 1. P r e-Clea n e r Ai r Filte r 1. 2. 2. Figure 30. Air Filter Service REPLA CE SP ARK PLUG Service Interval: Y ear ly Replacement Spark Plug: 5066 Spark Plug Gap: .030” (.76mm) 1. Stop the engine and allow it to cool. 2. Clean the area around the spark plug.
25 SER VICE & ADJUSTMENTS GR OUND SPEED CONTROL LEVER ADJUSTMENT The control le vers ha ve three adjustments: T o Adjust Contr ol Lever Height: Pull the lev ers in across the operator’ s lap to their DRIVE positions. Loosen the mount bolts (D , Figure 32) and raise or lo wer the le vers to the desired position.
26 BRAKE ADJUSTMENT 1. Stop the unit, turn the ignition OFF , set the ground speed le vers to P ARK positions, and w ait f or all moving parts to stop. 2. Locate the brak e rod (A, Figure 34) and adjustment nut (B). 4. Measure the parking brake spring.
27 Figure 35. Measure Blade Tips to Ground A. Mower Dec k B. Blade Tip C. Level Gr ound A B C Figure 36. Orient Blades Side-to-Side MO WER DECK LEVELING ADJUSTMENTS Side to Side Leveling If the cut is une ven, the mo wer ma y need lev eling. Unequal or improper tire pressure ma y also cause an une ven cut.
28 Figure 38. Orient Blades Fr ont-to-Back Front T o Back Le veling If the cut is une ven, the mo wer ma y need lev eling. Unequal or improper tire pressure ma y also cause an une ven cut. See CHECK TIRE PRESSURE. 1. T ur n the blades front-to-back as sho wn in Figure 38.
29 ST ORA GE W ARNING Never store the unit (with fuel) in an enc losed, poorly ventilated structure. Fuel vapor s can travel to an ignition sour ce (such as a furnace, water heater , etc.) and cause an explosion. Fuel vapor is also to xic to humans and animals.
30 TR OUBLESHOO TING While normal care and regular maintenance will extend the lif e of your equipment, prolonged or constant use ma y e ventually require that service be performed to allow it to continue operating properly . The troub leshooting guide below lists the most common prob lems, their causes and remedies.
31 T roubleshooting the Mo wer PROBLEM CA USE REMED Y Mower cutting height does not adjust. Cutting height motor screw dirty or requires lube. Thoroughly clean and lubricate cutting height motor screw . Cutting height linkage disconnected. Check that mo wer linkage is connected.
32 SPECIFICA TIONS SER VICE ITEMS ENGINE: Make Briggs & Stratton Model Intek Horsepower 20 @ 3600 rpm Displacement 30.59 Cu. in (501cc) Electrical System 12 V olt, 9 amp . Alter nator , Batter y: 230 CCA Oil Capacity 44 Oz. (1.3 L) w/o filter ; 48 Oz.
NO TES 33.
Lawn Care & Mowing Information LC-1 HO W AND WHEN T O W A TER, FER TILIZE & AERA TE Mo s t lawn s are watered too often, but with too little water.
LC-2 Lawn Care & Mowing Information WHEN AND HO W OFTEN T O MO W The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: ● Mow when the grass is between 3”-4” (7,5-10 cm) high.
MANUF A CTURING, INC . 500 N Spring Street / PO Box 997 P or t W ashington, WI 53074-0997 www .SimplicityMfg.com Briggs & Stratton Y ard P ower Products Group Cop yright © 2007 Br iggs & Stratton Corporation Milwauk ee, WI USA. All Rights Reserved PRODUCTS , INC .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Briggs & Stratton 150Z Series è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Briggs & Stratton 150Z Series - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Briggs & Stratton 150Z Series imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Briggs & Stratton 150Z Series ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Briggs & Stratton 150Z Series, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Briggs & Stratton 150Z Series.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Briggs & Stratton 150Z Series. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Briggs & Stratton 150Z Series insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
