Manuale d’uso / di manutenzione del prodotto Soneplex P-61-743 del fabbricante ADC
Vai alla pagina of 30
ADCP-61-743 • Issue 3 • September 2004 1304058 Page 1 2004, ADC Telecommunications, Inc. Soneplex ® Remote Test Access Unit (RTAU) User Manual ) Content Page 1 DESCRIPTION ......................................................................
ADCP-61-743 • Issue 3 • September 2004 Page 2 2004, ADC Telecommunications, Inc. Related Publications Listed below are related manuals and their pub lication numbers. Copies of these publications can be ordered by contacting the ADC Technical Assistance Center at 1-800-366-3891.
ADCP-61-743 • Issue 3 • September 2004 Page 3 © 2004, ADC Telecommunications, Inc. FCC Compliance Statement The Remote Test Access Unit has been certified to comply with the requirements for Class A computing devices per part 15 of the FCC regulations.
ADCP-61-743 • Issue 3 • September 2004 Page 4 2004, ADC Telecommunications, Inc. 1 DESCRIPTION The Remote Test Access Unit (RTAU) (Figur e 1) provides maintenance functionality for monitoring and intrusive test access to the DS1 channels in the chassis between the DS3 MUX and the low speed distribution modules (DLX, HLXC, ODS2, and RLX).
ADCP-61-743 • Issue 3 • September 2004 Page 5 © 2004, ADC Telecommunications, Inc. 11897-A RTAU STATUS LINE CODE INTRUSIVE TEST B8ZS AMI BIPOLAR ACCESS D S 1 RX TX Figure 1.
ADCP-61-743 • Issue 3 • September 2004 Page 6 2004, ADC Telecommunications, Inc. 1.1 DS3 MUX Compatibility Refer to Table 1 for compatibility informati on for DS3 MUXs, test access units, and MPU/SCU software versions.
ADCP-61-743 • Issue 3 • September 2004 Page 7 © 2004, ADC Telecommunications, Inc. 2.1 Initial Installation This installation procedure applies to the firs t time an IBBC shelf will be populated with a RTAU module. If the IBBC shelf has alrea dy been populated with a RTAU module, go to 2.
ADCP-61-743 • Issue 3 • September 2004 Page 8 2004, ADC Telecommunications, Inc. 14185-A RTAU MODULE HSW HSP TAU APU SCU MXP MXW DS3 FAIL RESET LMPTST/ APS LPBK ENABLE ONLINE STATUS APS LOCKOU.
ADCP-61-743 • Issue 3 • September 2004 Page 9 © 2004, ADC Telecommunications, Inc. 2.2 Maintenance Installation (Existing System) Replacement of the RTAU module in existing IBBC shelves should follow normal maintenance procedures.
ADCP-61-743 • Issue 3 • September 2004 Page 10 2004, ADC Telecommunications, Inc. 3 LED CHECK 1. When the RTAU module (Figure 3) is seated, the STATUS LED will be lit red for approximately 5 seconds. All LEDs will then flash yellow, and then the STATUS LED will be lit green.
ADCP-61-743 • Issue 3 • September 2004 Page 11 © 2004, ADC Telecommunications, Inc. 4 FRONT PANEL OPERATION All controls and indicators of the RTAU includi ng the jack accesses for a selected DS1 signal are located on the front panel (Figure 3). The cont rols and indicators are described in Table 2.
ADCP-61-743 • Issue 3 • September 2004 Page 12 2004, ADC Telecommunications, Inc. 5 CONFIGURATION Use this menu to view or edit the configuration for the RTAU module after it is installed in the chassis. This menu can also be used to equip, provision, assign thresholds, and assign service state.
ADCP-61-743 • Issue 3 • September 2004 Page 13 © 2004, ADC Telecommunications, Inc. 5. Use the arrow or number keys to select RTAU Setup and Control from the RTAU Configuration menu. Press Enter or Return . The RTAU Setup and Control screen will appear as shown in Figure 6.
ADCP-61-743 • Issue 3 • September 2004 Page 14 2004, ADC Telecommunications, Inc. SYSTEM MAINTENANCE 1. Force/APS Commands 2. Reset/LED Test Commands 3. Execute ACO (Alarm Cutoff) 4. Loopback Status/Commands 5. Display Inventory 6. Display Circuit IDs 7.
ADCP-61-743 • Issue 3 • September 2004 Page 15 © 2004, ADC Telecommunications, Inc. 7. Assign the selections by pressing Enter or Return. RTAU SETUP AND CONTROL EQUIPMENT SETUP =============== Cu.
ADCP-61-743 • Issue 3 • September 2004 Page 16 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields FIELD TYPE OPTIONS DESCRIPTION DEFAULT EQUIPMENT SETUP FIELDS Current User Toggle OV E R V IE W : T h e C u r r en t U s e r f i el d c a n o n l y b e set to NONE or CRAFT from the Craft menu.
ADCP-61-743 • Issue 3 • September 2004 Page 17 © 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT EQUIPMENT SETUP FIELDS, c.
ADCP-61-743 • Issue 3 • September 2004 Page 18 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT EQUIPMENT SETUP FIELDS, .
ADCP-61-743 • Issue 3 • September 2004 Page 19 © 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT SIGNAL GENERATOR SETUP FI.
ADCP-61-743 • Issue 3 • September 2004 Page 20 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT SIGNAL GENERATOR SETUP FIELDS, continued Pattern Type, continued Toggle 1 in 8 Containi ng strings of 7 sequential 0’s.
ADCP-61-743 • Issue 3 • September 2004 Page 21 © 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT SIGNAL GENERATOR SETUP FI.
ADCP-61-743 • Issue 3 • September 2004 Page 22 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT BIT ERROR SETUP FIELDS OVERVIEW: Bit errors can be injected by th e RTAU using the Bit Error Set Up fields.
ADCP-61-743 • Issue 3 • September 2004 Page 23 © 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT Elapsed Time ES Display only None Six-digit counter or blank. Blank Elapsed Time EFS Display only None Six-digit counter or blank.
ADCP-61-743 • Issue 3 • September 2004 Page 24 2004, ADC Telecommunications, Inc. DS3 MUX RT A U P A TTERN GEN DETECT OR CONTROLLER A B MPU or SCU LINE CARD DS1 TEST SET RX TX BIPOLAR A CCESS RT AU FRONT P ANEL DS3 EQUIPMENT MONIT OR SPLIT DS1 F ACILITY 11864-C Figure 8.
ADCP-61-743 • Issue 3 • September 2004 Page 25 © 2004, ADC Telecommunications, Inc. DS3 MUX RT AU AB EQUIPMENT (E) [NETWORK] F A CILITY (F) [CUST OMER] CIRCUIT UNDER TEST TEST SIGNAL GENERA T OR .
ADCP-61-743 • Issue 3 • September 2004 Page 26 2004, ADC Telecommunications, Inc. A END INTEROFFICE F ACILITY CPE INSERT : NETWORK DROP: NETWORK FE 11868-B Z END CPE SPL TE RT AU QRS B = ".
ADCP-61-743 • Issue 3 • September 2004 Page 27 © 2004, ADC Telecommunications, Inc. SPL TF INSERT : NETWORK DROP: CUST OMER INSERT : CUST OMER FE QRS A END CPE RT AU INTEROFFICE F ACILITY Z END C.
ADCP-61-743 • Issue 3 • September 2004 Page 28 2004, ADC Telecommunications, Inc. DS3 MUX RT AU A B A B EQUIPMENT (E) [NETWORK] F A CILITY (F) [CUST OMER] CIRCUIT UNDER TEST SIGNAL PRESENCE DE.
ADCP-61-743 • Issue 3 • September 2004 Page 29 © 2004, ADC Telecommunications, Inc. Table 4. TL1 Commands Used for the RTAU COMMAND DESCRIPTION CHG-ACCMD-T1 Change Access Mode T1 CHG-LPBK-T1 Chan.
ADCP-61-743 • Issue 3 • September 2004 Page 30 8 CUSTOMER INFORMATION AND ASSISTANCE ADC Technical support is available 24 hours a day, 7 days a week by contacting the ADC Technical Assistance Center. Sales Assistance 800.366.3891 • Quotation Proposals • Ordering and Deli very • General Product Informati on Systems Integration 800.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il ADC Soneplex ADCP-61-743 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del ADC Soneplex ADCP-61-743 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso ADC Soneplex ADCP-61-743 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul ADC Soneplex ADCP-61-743 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il ADC Soneplex ADCP-61-743, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del ADC Soneplex ADCP-61-743.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il ADC Soneplex ADCP-61-743. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo ADC Soneplex ADCP-61-743 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
