Manuale d’uso / di manutenzione del prodotto DWS 54100 SS del fabbricante Blomberg
Vai alla pagina of 25
Installation Manual Dishwasher FOR MODELS (ADA Height) DWS 54100 SS DWS 54100 FBI USA.
Installation Manual For Dishwasher Models DWS 54100 SS DWS 54100 FBI.
1. IMPORT ANT SAFETY INSTRUCTIONS 1 1.1 INSPECT THE DISHW ASHER 2 1.2 HOW T O CONT ACT US : 2 2. TOOLS WHICH MA Y BE NEEDED 3 3. MA TERIALS WHICH MA Y BE NEEDED 3 4. MA TERIALS SUPPLIED 4 4.1 P ARTS SUPPLIED 4 4.2 MANUAL BAG 4 4.3 DISHW ASHER P ARTS BAG 1 4 4.
1 USA INTRODUCTION Please read this installation manual and particularly the safety instructions completely and carefully . They will save you time and effort and help to ensure optimum dishwasher performance.
2 USA • Dishwasher must be secured to adjacent cabinetry using the brackets provided. Failure to do this may cause damage to property or bodily injury . • Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload.
3 USA 2. TOOLS WHICH MA Y BE NEEDED 3. MA TERIALS WHICH MA Y BE NEEDED (Additional materials may be required to comply with local codes) Hot W ater Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. UL listed conduit connector or strain relief.
4 USA 4.
5 USA 5. DISHW ASHER SPECIFICA TIONS 5.1 TECHNICAL FEA TURES Load capacity 8 place settings Permissible water pressure 4.35 - 145 psi (0.3 - 10 bars) Electrical connection 120 V (volts), 12 A (amps), .
6 USA 6. ENCLOSURE PREP ARA TION 6.1 ELECTRICAL PREP ARA TION W ARNING The dishwasher is designed for an electrical supply of 120 V , 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes.
7 USA 6.3.1 INST ALLING THE FOOT SUPPORTS Supplied ( 4 ) If the height of the enclosure is 33 7 / 16 ” to 34 1 / 4 ” (850mm - 870mm) use short supports as shown in the figure. Supplied ( 4 ) If the height of the enclosure is above 34 1 / 4 ” (870mm) use long supports as shown in the figure.
8 USA Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height.
9 USA 6.4 PREP ARING THE W A TER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher ’s water inletvalve.
10 USA 6.5 DRAIN PREP ARA TION The dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A , B , C ). Notice : • Either one of the above methods must be used or the dishwasher will not operate properly .
11 USA 6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top.
12 USA 7. PLACEMENT OF DISHW ASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure.
13 USA 7.1.2 W A TER SUPPL Y CONNECTION W ater supply may be connected to the dishwasher in one of two ways: • With metal braided hose. • With copper tubing. 7.1.3 BRAIDED HOSE/COPPER TUBING After connections are made turn on the water supply to check for leaks.
14 USA 7.3 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet you must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop.
15 USA Lock the toe kick brackets as shown with the plastic tab in the figure C by pushing the plastic tab on the dishwasher into the teeth of the bracket ( C ).
16 USA 7.5 INST ALLING THE OUTER DOOR (DWS 54100 FBI) Measure the height and width of the enclosure (Figure A ) and the toe kick.
17 USA 5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1 / 8 ” x 5 / 8 ” (Ø 3.5mm x 14mm) (Figure A ). 6. Mount the wooden door onto the dishwasher with the plastic mounting brackets which you have attached (Figure B ).
18 USA 7. Open the door and remove the two caps and two screws inside the door at position 1 and 3 (Figure C ).
19 USA 1 1. Check whether the bottom of the door hits the toe kick of the kitchen cabinet ( A ). 1 1.1. If the door hits the toe kick cut the necessary section out of the toe kick ( B ). 1 1.2. Apply silicon or sealant to the cut edge of the kitchen cabinet toe kick or paint so it does not absorb moisture.
20 USA .
21 USA 8. INST ALLER CHECKLIST Y our installer must have completed and checked the following: • The dishwasher is square and level. • The dishwasher is fastened securely to the cabinetry . • The dishwasher door opens and closes freely .
17 9872 01 00-AA- USA.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Blomberg DWS 54100 SS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Blomberg DWS 54100 SS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Blomberg DWS 54100 SS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Blomberg DWS 54100 SS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Blomberg DWS 54100 SS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Blomberg DWS 54100 SS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Blomberg DWS 54100 SS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Blomberg DWS 54100 SS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
