
1 Safety instructions
Please read these operating instruc- tions through carefully. Please make sure you read the safety instructions on the first pages of these operating instructions! Keep the operating instructions for future reference. Pass them on to any future owners.
This appliance corresponds to accepted technological standards with regards to safety and to the German Appliance Safety Law. Nevertheless, as a manu- facturer we consider it our obligation to make you aware of the following safety information.
1 With the warning triangle and/or by means of key words (Danger!, Cau- tion!, Important!), information is emphasized which is important for your safety or the correct functioning of the appliance. It is essential that this information is observed. 0 This symbol guides you step by step when operating the appliance.
3 Next to this symbol you receive addi- tional information and practical tips on using the appliance.
2 Tips and information about the eco- nomical and environmentally friendly use of the appliance are marked with the clover.
A Case B Strainer insert C Lid D Button E Handle F Water level indicator G Pilot light H ON/OFF switch J Temperature control K Separate base and mains cable L Rating plate
kettle, – and after each time it is used, – and for faults during operation. • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction con- cerning use of the appliance by a per- son responsible for their safety.

2 Packaging material The packaging materials are environ- mentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PEPS
The symbol W on the product or on its packaging indicates that this pro- duct may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electro- nic equipment. By ensuring this pro- duct is disposed of correctly, you will help prevent potential negative conse- quences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

When the adjusted temperature is reached resp. the water has boiled the kettle will switch off automatically. If the kettle is only filled with a little water, it takes longer to switch off.
Before using your new kettle you should wipe it inside and outside with a damp cloth due to hygienic reasons.
Initial use 0 Place the base unit (K) on a firm sur- face. 0 Plug the mains plug into a wall socket.
This appliance is equipped with a boil- dry safety cut-out. This feature pro- tects the appliance from overheating when started without water or from boiling until it is empty if used with the lid open. If the appliance is acci- dently switched on without water, it is automatically protected against over- heating. The heating process is auto- matically interrupted. Before using the kettle again let it cool down for 5-10 minutes.
3 If the mains cord is longer than neces- sary it can be wound up at the bottom of the base unit (K). 0 Press button (D) down to open the lid (C). 0 Fill with at least sufficient water to make it visible on the water level indi- cator (F), but not higher than the max. mark. 0 Close the lid (C) until it engages. The automatic switch off can only function reliably if this is done. 0 Place the kettle onto the base (K). 0 Set the desired temperature with the temperature controller (J). For boiling water, rotate the controller to the right to the position. 0 Press the ON/OFF switch (H) down, the pilot lights (G) lights up and the kettle starts to heat up.
1 Always disconnect the kettle from the mains supply before cleaning.
1 Never clean the kettle and base unit under running water or immerse it in washing-up water. 0 Occasionally rinse out the kettle with clean water. 0 Clean the outside of the appliance only using a damp cloth. Do not use any caustic or abrasive cleansing agents. 0 Hold strainer insert (B) at grip (1) and lift insert out for cleaning. 0 The heating base is made of stainless steel. If, however, spots of rust appear, these are only deposits adhering to the surface. They can be removed with a stainless steel cleaning agent.
3 The ON/OFF switch (H) only catches when the kettle is on the base unit (K).
3 Do not use the water from the first boiling cycle to prepare food.
The kettle will switch off automatically and the pilot light will go out when the adjusted temperature is reached resp. the water has boiled or the kettle is removed from the base. If you want to stop the heating process before the kettle automatically switches off, simply press the ON/OFF switch (H) up or lift up the jug from the base. If you want to reheat water which has already been heated, press the ON/OFF switch (H) down again.

Technical data
Lime scale deposits on the bottom of the kettle result in loss of energy and can affect the service life of the appli- ance. The appliance switches off before boiling if the layer of scale is too thick. It is then very difficult to remove. The appliance should be descaled regu- larly depending on the level of the water hardness. Use a standard des- caler following the directions; prefera- bly choose an environmentally friendly, descaling agent suitable for stainless steel according to the instructions from the manufacturer. 0 First fill in water, then a standard des- caling preparation which is not too strong.
Mains voltage: 220 - 240 V/50 Hz Power drain: 2000 - 2400 W Max. filling volume: 1,7 litres
1 Do not boil the solution as it could foam over. 0 After descaling, rinse the kettle out thoroughly with clean water. Never pour descaling agents into an enamel sink and do not reuse them.
What to do if ...
scaled. Treat with standard commer- cial descaling agent suitable for stainless steel. Note the directions for use from the manufacturer. – The temperature controller (J) is not
water, the appliance has not yet cooled sufficiently. Wait a short time before trying again.
I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.