Manuale d’uso / di manutenzione del prodotto K8T890-A9 del fabbricante Biostar
Vai alla pagina of 32
K8T890-A9 i FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These li mits are designed to provide reasonable protection against harmful interference in a residenti al installation.
Table of Contents ii Chapter 1: In troduction ............................................................... 1 1.1 Motherboard Featur es ...................................................................... 1 1.2 Package List .......................
K8T890-A9 1 CHAPTER 1: INTRODUCTION 1.1 M OTHERBOARD F EATURES A. Hardware CPU Supports AMD Socket 939. Supports AMD Athlon 64 FX/ Athlon 64/ Athlon 64 X2 proce ssor . AMD 64 architecture enables sim ultaneous 3 2 and 64 bit computing. Supports Hyp erT ransport T echnology up to 2000MT/s Full duplex.
K8T890-A9 2 System Memory Supports dua l channel DDR up to 8 banks. Supports 266 /333/400MHz DDR devices. Maximum memory size is up to 4GB. (Following t able is only for reference.
K8T890-A9 3 Internal On-board I/O Connectors and Headers 1 front panel header suppo rts front pan el facilities. 1 CD-in connector support s 1 CD-ROM audio-in device. 1 front audio header support s front panel audio fun ctio n. 1 S/PDIF-Out connector support s digit al audio-out function.
K8T890-A9 4 B. BIOS & Software BIOS Award legal BIOS. Supports APM1.2. Supports ACPI. Supports USB Function. Software Supports 9 th T ouch TM , Flasher TM , WinFlasher TM , and W arp speeder TM . 1.2 P ACKAGE L IST FDD cable x1 HDD cable x1 User ’s Manual x1 Fully Setup Driver CD x1 Rear I/O panel for A TX case x1 USB 2.
K8T890-A9 5 1.3 L AYOUT AND C OMPONENTS JKBMS1 JUSB3 JAUDI O1 JUSBLAN1 JKBV1 JUSBV1 JAUDIO2 PCI1 PCI3 PCI2 JCDIN1 JSPDIF_OUT1 Codec K8T890 JA TXPW R2 JUSBV2 JUSB2 JUSB1 JCF AN1 V T8237R JSA T A2 JSA T.
K8T890-A9 6 CHAPTER 2: HARDWARE INSTALLATION 2.1 I NSTALLING C ENTRAL P ROCESS ING U NIT (CPU) Step 1: Remove the so cket protection cap. Ste p 2: Pull the lever toward direction A from the socket and th en raise the lever up to a 90-degree angle.
K8T890-A9 7 Step 4: Hold the CPU do wn firmly , and then close the lever toward dire ct B to complete the installation. B Step 5: Put the CPU Fan on the CPU a nd buckle it. Connect the CPU F AN power cable to the JCF AN1. This completes the inst allation.
K8T890-A9 8 2.3 I NSTALLING S YSTEM M EMORY DIMM2 DIMM4 DIMM1 DIMM3 2.2.1 DDR Module installation 1. Unlock a DIMM slot by pressing the retaining clip s outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2.
K8T890-A9 9 2.4 C ONNECTORS AND S LOTS FDD1: Floppy Disk Connector The motherboard provides a st andard floppy disk connector that supports 36 0 K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector su ppo rts the provide d floppy drive rib bon cables.
K8T890-A9 10 PCI1~PCI3: Peripheral Component Interconnect Slots This motherboard is equipped with 3 st andard PCI slo t s. PCI st ands for Peripheral Component Interconnect, and it is a bu s st andard for expansion cards. This PCI slot is desig nated as 32 bit s.
K8T890-A9 11 XGP1: Xtreme Graphics Port Slot This XGP (Extreme Graphics Po rt) sl ot is a special design that only supports compatible AGP VGA cards. To install the system with an add-on AGP VGA card, please ma ke sure to install the driver of add-on AGP VGA card before onboard VGA driver installation.
K8T890-A9 12 CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 H OW TO S ETUP J UMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened Pin closed Pin1-2 closed 3.
K8T890-A9 13 JKBV1: Power Source Header for PS/2 Keyboard and Mous e 1 3 Pin 1-2 Close +5V for PS/2 key board and mouse. 3 1 1 3 Pin 2-3 close PS/2 keyboard and mouse are powered by +5V st andby voltage. Note: In order to support this function “Power-on system via keyboard and mouse”, “JKBV1” jumper cap should be placed on Pin 2-3.
K8T890-A9 14 JATXPWR2: ATX Power Source Connector By connecting this connector , it will provide +12V to CPU power circuit. Pin Assignment 1 +12V 2 +12V 3 Ground 1 4 2 3 4 Ground JUSB1/JUSB2: Head ers for USB 2.
K8T890-A9 15 JPANEL1: Front Pan el Head er This 24-pin connector includes Power-on, Reset, HDD LE D, Po wer LED, Sleep button, speaker and IrDA Connection.
K8T890-A9 16 JSPDIF_OUT1: Digital A udio-out Connector This connector allows user to connect the PCI bracket SPDIF output hea der. Pin Assignment 1 +5V 2 SPDIF_OUT 1 3 3 Ground JSPDIF_IN1 (optiona l): Digital Audio-in Conn ector This connector allows user to connect the PCI bracket SPDIF input hea der .
K8T890-A9 17 JAUDIO1: Front Pan el Audio Head er This header allo ws user to connect the front aud io output cable with the PC front panel. It will disable the output on back panel audio connectors.
K8T890-A9 18 JCMOS1: Clear CMOS Head er By placing the jumper on pin2-3, it allo ws user to restore the BIOS safe setting and the CMOS data, please carefully follow the proced ures to avoid damaging the motherboard. 3 1 Pin 1-2 Close: Normal Operation (default).
K8T890-A9 19 CHAPTER 4: USEFUL HELP 4.1 A WARD BIOS B EEP C ODE Beep Sound Meaning One long beep followed by t wo short beeps Video card not found or video card memory bad High-low siren soun d CPU ov.
K8T890-A9 20 B. CPU Overheated If the system shutdown aut omatically aft er po wer on system for seconds, that means the CPU prot e ction function ha s been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.
K8T890-A9 21 4.3 T ROUBLESHOOTING Probable Solution 1. No power to the system at all Power light don’t illuminate, fan inside power supply does not turn on. 2. Indicator light on keyboard does not turn on. 1. Make sure power cable is securely plugged in.
K8T890-A9 22 CHAPTER 5: WARPSPEEDER™ 5.1 I NTRODUCTION [W arpS peeder™], a new powerful co ntrol utility , featur es three user-friendly functions inclu ding Overclock Manager , Overvoltage Manager , and Hardware Monitor .
K8T890-A9 23 5.3 I NSTALLATION 1. Execute the setup execution file, and then the following dialog will pop up. Please click “Next” button and follow the default proce dure to install. 2. When you see the following dialog in setup procedure, it means setup is completed.
K8T890-A9 24 5.4 [W ARP S PEEDER ™] INCLUDES 1 TRAY ICON AND 5 PANELS 1. Tray Icon: Whenever the T ray Icon utility is l aunched, it will display a little tray icon on the right side of Windows T askbar . This utility is responsible for conveniently invoking [W arpS peeder™] Utility .
K8T890-A9 25 2. Main Panel If you click the tray icon, [W ar pS peeder™] utility will be invoked. Please refer to the following figure; the utility’ s first window you will see is Main Panel. Main Panel cont ains features as follows: a. Display the CPU S peed, CPU external cloc k, Memory clock, AGP cloc k, and PCI clock information.
K8T890-A9 26 3. Voltage Panel Click the V oltage button in Main Panel, the button will be highlighted and the V oltage Panel will slide out to up as the following figure. In this panel, you can decide to increa se CPU core voltage a nd Memory voltage or not.
K8T890-A9 27 4. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel will slide out to lef t as the following figure.
K8T890-A9 28 c. “Auto-overclock button”: Us er can click this button and [W arpS peeder™] will set the best and stable pe rform ance and frequency automatically . [W arpS peeder™] utility will execute a series of testing until system fail. Then system will do fail-safe reboot by using W atchdog function.
K8T890-A9 29 6. About Panel Click the “about” button in Main Panel, the button will be highlig hted and the About Panel will slide out to up as the following figure. In this panel, you can get model name and det ail information in hint s of all the chipset that are related to overclocking.
K8T890-A9 30 Note: Because the overclock, overvolt ag e, and hardware monitor featu re s are controlled by several separate chip set, [W arpS peeder™] divide these features to separate panels. If one chip set is not on board, the correlative button in Main p anel will be di sabled, but will not interfere other panels’ functions.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Biostar K8T890-A9 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Biostar K8T890-A9 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Biostar K8T890-A9 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Biostar K8T890-A9 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Biostar K8T890-A9, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Biostar K8T890-A9.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Biostar K8T890-A9. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Biostar K8T890-A9 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
