Manuale d’uso / di manutenzione del prodotto 170PAX2TM del fabbricante Zebra Technologies
Vai alla pagina of 84
Zebra 170 P AX 2 ™ - Series User ’s Guide RIGHT HAND LEFT HAND R.
P roprietary Statement This manual contains proprietary information of Zebra T echnologies Corporation. It is intended solely for the information and use of parties operating and maintaining t h e equipment described herein.
Contents Introduction Zebra 170 PA X 2 Print Engine ......................1 Getting Started .............................1 Print Engine Mounting .........................1 Communications ............................1 Printer Power ....................
Care & Adjustments Cleaning ................................3 3 T oggle Positioning ...........................3 5 Printhead Pressure Adjustment ....................3 5 T roubleshooting Power On Self T est ..........................3 7 Power On T roubleshooting .
Introduction Congratulations! Y ou have just purchased a high-quality thermal demand print engine manufactured by the industry leader in quality , service, and value. For over 25 years, Zebra T echnologies Corporation has provided customers with the highest caliber of products and support.
A DB-15 Applicator Interface Connector provides communication between the print engine and the associated applicator hardware. In some applications, control signal timing may be a critical element in the performance of the print engine. Refer to Appendix B for control signal descriptions.
Media & Ribbon Loading Media Loading If your print engine is a right hand unit (printed labels are presented on the right hand side of the unit), refer to Figure 2 while performing the procedure shown below . If your print engine is a left hand configuration (printed labels are presented on the left hand side of the unit), refer to Figure 3.
5. Ensure the media is aligned within the print path then close the printhead assembly (C) by rotating the printhead lock lever (D) until it latches onto the locking pin (E). 6. Secure the pinch roller (F) in position by pressing down on the top of the pinch roller latch (G) until the assembly snaps closed.
Ribbon Loading T o load ribbon, refer to Figure 4 (for right-hand units) or Figure 5 (for left-hand units). NOTE: Do not load ribbon if the printer is to be used in the direct thermal mode.
Left Hand Units 1. Push the ribbon roll onto the supply spindle (N) as far as it will go, so the ribbon feeds as shown in Figure 4. 2. Install an empty ribbon core onto the ribbon take-up spindle (O). 3. Open the printhead assembly (C) by unlatching the print- head lock lever (D) from the locking pin (E).
Media Sensor Position Reflective Media Sensor Some types of media have black marks printed on the underside of the backing material that act as “Start of Label” indicators. These black marks are sensed by the reflective media sensor mounted on the printer frame.
8 170 PA X 2-Series User’s Guide.
Printer Operation P ower On/Off Switch The Power On/Off Switch is located just to the left (or right) of the printer ’ s control panel. When this switch is placed in the ON (1) position, the POWER light goes ON and the printer automatically performs a Power On Self T est (POST).
Liquid Crystal Display The control panel shown in Figure 7 contains a backlit Liquid Crystal Display . It shows operational status as well as programming modes and feature parameters. Control P anel Keys Five keys are used to set print and communication parameters.
Configuration and Calibration After you have installed the media and ribbon, plugged in and turned on the AC Power , and the printer has completed the Power On Self T est (POST), you may configure the printer parameters for your application using the Liquid Crystal Display and the control panel keys.
Cancel — cancels all changes since pressing the SETUP/EXIT key except Darkness and T ear Off (if they were changed). Load Defaults — loads factory defaults as the printer ’ s operating parameters.
Setting the T ear Off Position The T ear Off Position adjusts the position of the media over the peel bar after printing. The label and backing can be torn off or cut between labels. This also af fects the dispense position in Peel Off, Applicator , and Cutter modes.
Press the right or left oval key to display other selections. Default: W eb (used to sense notches or holes in media or liner between labels) Selections: W eb, Mark (used to sense black marks on the back of the media or liner) Press the NEXT key to display PRINT METHOD .
NOTE : Before you begin the media and ribbon calibration procedure, be sure the Maximum Length is set to a value one step greater than the actual media. If the Maximum Length is set to a lower value, the printer will assume that continu- ous media is loaded.
Listing P rinter Information List Fonts This selection is used to print a label that lists all of the fonts currently available in the printer . Fonts may be stored in optional font EPROMs and as part of firmware EPROMs, on an optional PCMCIA memory card, or downloaded and stored in formatting memory (RAM).
Initialize Card This selection initializes the optional memory card. CAUTION: Perform this operation only when it is necessary to erase all previously stored information in the optional memory card. Otherwise, press the NEXT key to bypass this function and display SENSOR PROFILE .
Media and Ribbon Sensor Calibration When the print engine is first put into service, the following calibration process must be performed. This allows the printer to establish the proper settings for the specific media and ribbon being used in your application.
Media and Ribbon Calibration Changing the type of ribbon and/or media may require adjustments to the sensitivity of the media and ribbon sensors. Indications that the sensitivity may need to be adjusted would be a RIBBON light ON with the ribbon properly installed or non-continuous media being treated as continuous media.
Setting Communication P arameters Communication parameters must be set correctly for the printer to receive data from the host. These parameters ensure that the printer and host are “speaking the same language.” All communications parameters are password-protected.
Setting the P arity The parity of the printer must match the parity of the host for communications to take place. Select the parity that matches the one being used by the host. PARITY - EVEN + Press the right or left oval key to display other selections.
NOTE: Zebra Protocol is the same as ACK/NACK Protocol, except the response messages are sequenced. NOTE: If Zebra Protocol is selected, the printer must use “DSR/DTR” Host Handshake Protocol.
Selecting P refix and Delimiter Characters Prefix and delimiter characters are two-digit hex values used within the ZPL/ZPL II formats sent to the printer .
Selecting ZPL Mode The printer accepts label formats written in either ZPL or ZPL II. Refer to the “ ZPL II Programming Guide ” for more information on the differences between ZPL and ZPL II. The printer will remain in the selected mode until changed by this front panel instruction or by sending a ZPL/ZPL II command to the printer .
Press the right or left oval key to display other selections. Default: Feed Selections: Feed, Calibration, Length, No Motion Press the NEXT key to display HEAD CLOSE . Head Close Determines the action of the media after the printhead has been opened and then closed.
Setting the Label T op Position The Label T op Position controls the initial vertical print position on the label (viewed as the label exits the printer). The Default position is referenced to the leading edge of the label which follows the one to be printed.
Setting the Left Position The Left Position controls the initial print position from the left edge of a label (viewed as the label exits the printer). The Default position is referenced to the left edge of the media.
Head T est F unction Periodically a Head T est is automatically performed to ensure that the printhead elements are working correctly . This parameter determines how many labels are printed between these internal printhead tests.
OFF - The verifier port is off. 1 ERR — Label reprinted if verifier detects an error . If the bar code is near the upper edge of the label, the label will feed out far enough to be verified and then backfeed to allow the next label to be printed and verified.
P rinting Controls Setting the Start Print Signal This parameter determines how the printer will react to the Start Print Signal input on pin 3 of the applicator interface connector at the rear of the printer . This is set by the applicator manufactur er and should not be changed unless the factory defaults have been r eloaded.
Selecting the Ribbon Low Feature When the Ribbon Low feature is enabled, the “Ribbon Low” output signal (Pin 9) on the applicator port is functional. When the amount of ribbon on the supply spindle reaches a specific low level, the output signal will assert HIGH to provide a “Ribbon Low” warning.
LCD Adjust Adjusts the brightness of the Liquid Crystal Display . LCD ADJUST 00 - n + Press the left oval key to decrease the brightness; the right oval key to increase the brightness. Default: 00 Range: 00 to 19 Press the NEXT key to display LANGUAGE P rinter Language Selecting the Liquid Crystal Display (LCD) L anguage.
Care & Adjustments Cleaning CAUTION: Use only the cleaning agents indicated. Zebra T echnologies Corporation will not be responsible for damage caused by any other cleaning materials used on the 170 P AX 2-Series print engine. T able 1 provides a recommended cleaning schedule.
Cleaning the Printhead and Platen Roller Inconsistent print quality , such as voids in the bar code or graphics, or light print may indicate a dirty printhead. Media movement problems may indicate a dirty platen. For optimum print quality , perform the following cleaning procedure after every roll of ribbon.
NOTE: If print quality has not improved, try cleaning the printhead with the Save-a-Printhead cleaning film. This specially coated material removes contamina- tion buildup without damaging the printhead. Call your authorized Zebra distributor to order the Save-a-Printhead cleaning kit for the 170 PA X 2 printer (part # 38902M).
4. Use the adjusting nuts (S) to increase or decrease the spring pressure until the left and right edges of the printed area are equally dark. 5. Increase darkness to the optimum level for the media being used. 6. Hold the adjusting nuts (S) in position, and tighten the locking nuts (R) against them.
T roubleshooting P ower On Self T est A Power On Self T est (POST) is performed each time the printer is turned ON. During this test, the front panel lights (LEDs) will turn ON and OFF to ensure proper operation. At the end of this self test, only the POWER LED will remain lit.
The following tables provide trouble symptoms, a diagnosis of specific causes, and a recommended action which should result in proper printer operation.
SYMPTOM DIAGNOSIS ACTION WARNING HEAD COLD Printhead is not hot enough to print properly . Printing continues while printhead heats up. If error remains, environment may be too cold for proper printing. Relocate printer to warmer area. Verify print quality.
SYMPTOM DIAGNOSIS ACTION Wrinkled ribbon. Ribbon fed through the machine incorrectly. See “Ribbon Loading” on page 5. Incorrect burn temperature. Set the burn temperature to the lowest possible setting for good print quality. Incorrect or uneven printhead pressure.
SYMPTOM DIAGNOSIS ACTION ZPL II was sent to the printer, but not recognized. DATA light always OFF. or DATA light always flashing. Communications parameters are incorrect. Print a Communications Diagnostic Label. Check for format or overrun errors. Reset communication parameters.
P rinter Self T ests Introduction These self tests, illustrated on the following pages, produce sample labels and provide specific information that help determine the operating conditions for the printer . Each self test is enabled by pressing a specific control panel key or combination of keys while turning the power switch ON.
P A USE Key Self T est Press and hold the P AUSE key while turning the printer power ON. Release the key anytime after the first front panel LED turns OFF . This self test is actually comprised of four individual test features: 1. The initial self test prints 15 labels at 2" (5.
FEED Key Self T est Press and hold the FEED key while turning the printer power ON. Release the key anytime after the first front panel LED turns OFF .
FEED Key and P A USE Key Press and hold these two keys while turning the printer power ON. The printer configuration will be temporarily reset to the factory default values. These values will be active until power is turned OFF . If the factory default values are permanently saved, a media calibration pr ocedure must be performed.
Parameter Controlled by LCD Adjust Configuration Modes Enabled ZPL Modes Disabled ZPL Resolution Fixed (head type switch) Socket 1 ID Fixed (option EPROMS) Firmware Fixed (code EPROMS) Configuration C.
Options Y our print engine can be equipped with the following options. Contact your equipment supplier for further information and pricing. Single In-line Memory Module (SIMM) An optional 8 MByte SIMM increases the graphic and font storage capacity of the printer and/or increases the print length.
48 170 PA X 2-Series User’s Guide.
Printer Specifications Printing Considerations Media Type (continuous, die-cut, or black mark) 172 PAX 2 173 PAX 2 Resolution 203 dots per inch (8 dots per mm) 300 dots per inch (12 dots per mm) Dot size 0.0049” x 0.0049” (0.125 mm x 0.125 mm) 0.0033” x 0.
Zebra Programming Language (ZPL II) Bar Codes Communications Specifications 50 170 PA X 2-Series User’s Guide Printer Specifications ° Communicates in printable ASCII characters ° Controlled via m.
Standard Printer Fonts Printer Specifications 170 PA X 2-Series User’s Guide 51 Font Matrices for 12 dot/mm (300 DPI) Printhead Font Matrix (in dots) Type* Character Size Inches Millimeters Height Width Inter- character Gap Height Width Char ./inch Height Width Char .
Memory ° 1 MByte RAM standard Optional 8 MByte SIMM Option available for longer labels or additional storage of fonts, graphics, logos, and label formats ° T ype II Serie sC&DP C Card Interface (memory only) standard Optional 8 MByte PC Memory Card - available for additional storage of fonts, graphics, logos,templates, and label formats.
Appendix A AC P ower Cord Requirements Since many areas of the world have specific power requirements, an AC Power Cord may not be included with your printer . Refer to Figure 20. A power cord must be provided by you that meets your local electrical requirements.
T o replace a fuse, follow this procedure and refer to Figure 22: 1. T urn off the printer and unplug the power cord from the back of the printer . 2. Using a small-blade screwdriver , remove the fuse holder from the power entry module at the rear of the printer .
Appendix B P rinter Communications Interface T echnical Information System Considerations Communications Code — The printer sends and receives American Standard Code for Information Interchange (ASCII).
W ARNING: Connecting a data communications cable while the power is ON may damage the PA X 2 print engine. RS -232/RS -422/RS -485 Serial Data P ort The connections for these standard interfaces are made through the DB25 Female connector on the rear panel.
RS-232 Interconnections — The printer is configured as Data T erminal Equipment (DTE). Figure 23 illustrates the connections required to interconnect the printer with the standard 9-pin serial port connector on a PC. Figure 24 illustrates the internal connections of the printer ’ s RS-232 connector .
RS-422/RS-485 Interconnections — The printer may be connected to a host by a RS-422/RS-485 interface. The DB25 Female connector on the rear of the printer uses specific pins for this purpose. Figure 25 illustrates the required cable wiring for interconnecting to the printer ’ s DB25 connector .
Centronics- Compatible P arallel Data P ort A standard 36-pin Centronics-compatible parallel connector is available at the rear of the printer for connection to the data source. The standard RS-232 port will not accept data when the parallel port is enabled.
Cabling Requirements Data cables must be fully shielded and fitted with metal or metalized connector shells. Shielded cables and connectors are required to prevent radiation and reception of electrical noise. T o minimize electrical noise pickup in the cable: • Keep data cables as short as possible.
Appendix B 170 PA X 2-Series User’s Guide 61 PIN # SIGNAL NAME SIGNAL TYPE FUNCTIONAL DESCRIPTION 5 PAUSE Input To toggle the current PAUSE state, this input must be asserted LOW for 200 milliseconds, or until the SERVICE REQUIRED output (pin 10) changes state.
62 170 PA X 2-Series User’s Guide Appendix B INTERNAL LOGIC GROUND INTERNAL LOGIC TO J 1 PIN 2 TO J 1 PIN 1 J1 DB15 PRINT ENGINE INTERNAL CONNECTIONS PRINT ENGINE EXTERNAL CONNECTIONS SERVICE REQUIRED FEED RIBBON OUT RIBBON L OW ST ART PRINT 1.
Appendix C ASCII Code Chart 170 PA X 2-Series User’s Guide 63 HEX CHAR HEX CHAR HEX CHAR HEX CHAR 00 NUL 20 space 40 @ 60 ‘ 01 SOH 21 ! 41 A 61 a 02 STX 22 “ 42 B 62 b 03 ETX 23 # 43 C 63 c 04 E.
64 170 PA X 2-Series User’s Guide.
Appendix D Adjusting Darkness For “In-Spec” Bar Codes All direct thermal and thermal transfer materials do not require the same darkness setting. The best way to check for proper darkness is to use a bar code verifier that actually measures bars/spaces and will calculate the print contrast.
“In-Spec” The “in-spec” bar code can only be confirmed by a verifier , but it should exhibit some very visible characteristics. T he normal bar code will have complete, even bars and clear, distinct spaces. The rotated bar code will also have complete bars and clear distinct spaces.
Appendix E Installation Information V entilation openings of the printer mounting enclosure shall be provided by the installer to remove heat and ensure uninterrupted, trouble-free operation of the printer . Ambient air temperature surrounding the printer must not exceed 40 degrees Centigrade or 104 degrees Fahrenheit.
Consideration must be given to the current rating of the printer during installation so that when power is applied to the printer and the enclosing equipment, an overload condition is not effected on enclosing equipment circuits or supply wiring. Reliable earthing of the printer must be maintained.
NOTE: Mounting hole locations are identical for both the right hand and left hand print engines. Clearance at the rear panel of the electronics enclosure must provide ample space for electronic connec.
70 170 PA X 2-Series User’s Guide.
Glossary alphanumeric Indicating letters, numerals, and characters such as punctuation marks. backfeed When the printer pulls the media and ribbon (if used) backward into the printer so that the beginning of the label to be printed is properly positioned behind the printhead.
fanfold media Media that comes folded in a rectangular stack. Contrast this with r oll media . firmware This is the term used to specify the printer ’ s operating program. This program is downloaded to the printer from a host computer and stored in FLASH memory .
printer configuration (See configuration.) printhead wear The degradation of the surface of the printhead and/or the print elements over time. Heat and abrasion can cause printhead wear .
74 170 PA X 2-Series User’s Guide.
Index A AC Power ..................2 Adjustments Printhead pressure ...........3 5 T oggle positioning ..........3 5 Applicator Interface Connector ......6 0 Applicator Port, setting ..........2 9 ASCII Code Chart .............6 3 B Backfeed Sequence .
I IBM Coax Interface ............4 7 IBM T winax Interface ...........4 7 Images, printing a list ...........1 6 Initializing the Card ............1 7 In-Spec Bar Codes, adjusting darkness . . 65 L Label Positioning Parameters .......2 5 Backfeed sequenc e.
Printing considerations (specifications) . . 49 Program Mode Entering ................1 1 Leaving ................1 1 Passwords ...............1 1 Protocol, setting ..............2 1 R Reporting Damage .............1 Ribbon Loading .................5 Removal .
.
.
Customer Order # 49861L Rev . 1 Manufacturer Order # 49861LB © Zebra T echnologies Corporation Zebra T echnologies Corporation 333 Corporate W oods Parkway V ernon Hills, Illinois 60061-3109 U.S.A. Phone Number: +1 847. 634.6700 Fax Number: +1 847. 913.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Zebra Technologies 170PAX2TM è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Zebra Technologies 170PAX2TM - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Zebra Technologies 170PAX2TM imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Zebra Technologies 170PAX2TM ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Zebra Technologies 170PAX2TM, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Zebra Technologies 170PAX2TM.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Zebra Technologies 170PAX2TM. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Zebra Technologies 170PAX2TM insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
