Manuale d’uso / di manutenzione del prodotto VXR del fabbricante Yamaha
Vai alla pagina of 108
2012 W a veRunner VXS VXR OWNER’S/OPERATOR’S MANUAL F2M-F8199-11 LIT -18626-09-36 U .S.A. E d it i on Read this manual carefully before operating this water craft.
Read this manual carefully be fore operating this watercraft. This manual should stay with the WaveRunner i f it is sold . UF2M11E0.book Page 1 Monday, July 11, 2011 10:21 AM.
Important manual information EJU30182 To the owner/operator Thank you for choosing a Yamaha watercraft. This owner’s/o perator’s manual contains in- formation you w ill need for proper operation, maintenance, and care. A thorough under- standing of these simpl e instructions will help you to obtain maximum enjoyment from your new Yamah a.
Table of contents General and important labels .......... . 1 Identific ation numbers . ............ ....... 1 Primary Iden tification (PRI-ID) number ............ ................. .............. 1 Hull Iden tificatio n Number (HIN) ........ 1 Engine s erial numbe r .
Table of contents Pre-oper ation ch eck poin ts .......... 59 Pre-launc h checks .................... ....... 59 Post-lau nch checks .................. ....... 65 Operati on ................ ............. ............ 66 Operating your water craft .. .
General and important labels 1 EJU30262 Identification numbers Record the Primary Identification (PRI-ID) number, Hull Identification N umber (HIN), and engine serial num ber in the spaces provided for assistance when ordering gen uine parts from a Yamaha dealer.
General and important labels 2 EJU30352 Emission control information This engine conforms to U. S. Environmental Protection Agency (EPA) and/or California Air Resources Board (CARB) regulation s for ma- rine SI engines applicable at the time of man- ufacture.
General and important labels 3 stallation procedures and page 84 for engine cover removal and installa tion procedures.) EJU30440 Star la bels This watercraft is labeled with a Califo rnia Air Resources Board (CARB) star label. See be - low for a description of your particul ar label.
General and important labels 4 these standards have 65% lower emissions than One Star-Low Emission eng ines. Four Stars - Super Ult ra Low Emission The four-star label iden tifies engines that meet the Air Resources Board ’ s Sterndrive and Inboard marine engine 2009 exhaust emission standa rds.
General and important labels 5 EJU30452 Important labe ls Read the following labels before using this watercraft. If hav e any questions, consult a Yamaha dealer.
General and important labels 6 EJU35913 Warning labels If any of these labels are damaged or m issing, contact a Yamaha dealer for replacements. 1 2 UF2M11E0.
General and important labels 7 UF2M11E0.book Page 7 Monday, July 11, 2011 10:21 AM.
General and important labels 8 EJU35925 Other labels UF2M11E0.book Page 8 Monday, July 11, 2011 10:21 AM.
General and important labels 9 The following label indicates the co rrect direction to upright a capsized waterc raft. UF2M11E0.book Page 9 Monday, July 11, 2011 10:21 AM.
Safety information 10 EJU30671 The safe use and operation of this w ater- craft is dependent upon the use of proper riding techniques, as well as upon the common sense, good judgment, and ex- pertise of the operator. Every operator should know the following r equirements before riding the watercraf t.
Safety information 11 teristics of the watercraft before trying any difficult maneuvers. EJU30761 Cruising limitations ● Scan constantly for people, obj ects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.
Safety information 12 kles, and other bones. Do not jump wakes or waves. ● Do not operate the watercraft in rough wa- ter, bad weather, or wh en visibility is poor; this may lead to an accident causin g injury or death. Be alert to the p ossibility of ad- verse weather.
Safety information 13 EJU30812 Operation requirements ● All riders must wear a U.S. Coast Guard (USCG) approved personal flotation device (PFD) that is suitable for personal water- craft use.
Safety information 14 ● The operator and passengers s hould al- ways keep their feet on the floor of the foot- well when the w atercraft is in motion. Lifting your feet increases the chanc es of losing your balance, or hitting objects outside the watercraft with your feet.
Safety information 15 boating laws also require that the fire extin- guisher be approved by the U SCG. EJU30830 Recommended equipment The following items should be carried on board your watercraft: ● Sound-signaling device You should c arry a whistle or other sound- signaling device that can be used to s ignal other boats.
Safety information 16 EJU36850 Hazard information ● Never start the engine or let it run for any length of time i n an enclosed area. Exhaust fumes contain carbon mon oxide, a color- less, odorless gas that may cause loss of consciou sness and death within a short time.
Safety information 17 ● Reverse can be used to slow do wn or stop during slow-speed maneuv ering, such as when docking. Once the engine is idling, shift into reverse and gradua lly increase en- gine speed. Make sure that there are no ob- stacles or people behind yo u before shifting into reverse.
Safety information 18 EJU30943 Water-skiing You can use the watercraft for water-skiing if it has the seating capacity to carry the op era- tor, a rearward-facing spotter, and the w ater- skier when he or she is not skiing. The watercraft mus t also have a cleat de- signed to pull a ski rope; do not attach the rope to any other location.
Safety information 19 Make sure that the rope is not looped around anything. After checking that the skier is ready and that there is no traffic or other obstacles, ap - ply enough throttle to raise the skier. ● Make smooth, wide turns. The watercraft is capable of very sharp turns, which could ex- ceed the abilities of the skier.
Safety information 20 Give-way vessel The vessel which does not have the right-of- way has the duty to take positive and timely action to stay out of the way of the stand-on vessel. Normally, you shou ld not cross in front of the vessel with the right-of-way.
Safety information 21 provided the other vessel gives you the rig ht- of-way as it should. Overtaking If you are passing another vess el, you are the give-way vess el. This means that the other vessel is exp ected to maintain its co urse and speed. You must stay out of its way until you are clear of it.
Safety information 22 Many bodies of w ater used by boaters are en- tirely within the bou ndaries of a particular state. The Uniform State Waterway Marking System has been devise d for these waters. This system uses buoys and signs with dis- tinctive shapes and colors to show regulatory or advisory information.
Safety information 23 Remember, ma rkings may vary by geograph- ic location. Always consult local boating au- thorities before riding your watercraft in unfamiliar waters. EJU30982 To get more boating safety information Be informed about boating safety.
Safety information 24 EJU30991 Enjo y your w aterc raf t respo nsibly You share the areas y ou enjoy when riding your watercraft with others and with nature. So your enjoym ent includes a responsibil ity to treat these other people, a nd the lands, wa- ters, and wildlife with respect and courtes y.
Safety information 25 waterways stay open for the enjoyment of a variety of recreational opportu nities. UF2M11E0.book Page 25 Monday, July 11, 2011 10:21 AM.
Description 26 EJU40302 Watercraft glossary Trolling speed “ Trolling ” is the lowest maneuvering speed. You are apply ing little or no throttle. The watercraft is down in the water, and there is no wake. Sub-planing speed “ Sub-planing ” is a medium speed.
Descripti on 27 EJU31011 Location of main components Exterior 5 6 7 8 9 4 3 2 1 1 Hood 2 Handlebars 3 Seat (page 45) 4 F ootwell 5 Bow e ye (page 46) 6 Fuel filler cap (page 51) 7 Cooling water pilot outlet (page 35) 8 Gunwale 9 Sponson UF2M11E0.
Description 28 9 8 7 6 5 4 1 2 3 10 11 1 Boarding platf or m 2 Cleat (page 47) 3 Handgrip (page 46) 4 Reboarding step (VXR) (page 46) 5 Jet thr ust nozzle 6 Rev er se gate (page 37) 7 Ride plate 8 Stern ey e (page 47) 9 Stern drain plug (page 54) 10 Speed sensor 11 Intake gr ate UF2M11E0.
Descripti on 29 5 4 1 2 3 10 11 12 7 6 8 9 1 Star t switch (page 33) 2 Engine shut-off swit ch (page 33) 3 Clip (page 33) 4 Engine shut-off cord ( lany ard) (page 33) 5 Engine stop s witch (page 33) 6.
Description 30 Engine compartment 7 5 6 8 10 9 2 1 4 3 1 Engine cov er 2 Air filter case 3 W ater separator (page 35) 4 Fuel tank 5 Electrical box 6 Battery (page 60) 7 Flushing hose connector 8 Spark plug/Spar k plug cap/ Ignition coil 9 Engine oil filler cap (page 52) 10 Dipstick (page 52) UF2M11E0.
Control function operation 31 EJU31024 Watercraft control functions EJU41910 Remote control tra nsmitter The Yamaha Security System and Low RPM Mode settings c an be selected by operating the remote control transmi tter. (See page 32 for Yamaha Security System setting proce - dures and page 38 for Low RPM Mode activa - tion procedures.
Control function operation 32 two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includin g in- terference that may cau se undesired opera- tion.
Control function operation 33 TY ” indicator light blinks two or three times, then comes on. This indicates the un lock mode is selected. EJU31152 Engine stop switch “” The engine stop switch (red b utton) stops the engine when the sw itch is pushed.
Control function operation 34 in 5 seconds, release the start switch, wait 15 seconds, and then try again. NOTICE: Never push the start switch while the engine is running. Do not operate the start switch for more than 5 seconds, otherwise the battery will be discharged and the engine will not start.
Control function operation 35 Since the strength of the jet thrust determines the speed and de gree of a turn, throttle must always be applied when attempting a turn, ex- cept at trolling speed. This model is equipped with the Yamaha En- gine Management System (YEMS) that in- cludes an off-throttle s teering (OTS) system.
Control function operation 36 To drain water from the water separator: (1) Place a drain pan or dry cloth under the water separator. (2) Gradually loosen the drain screw to drain the water. Catch the draining water in the drain pan or s oak it up w ith the dry cloth so that it does not spill into the engine compartment.
Watercraft operation 37 EJU40011 Watercraft operation functions EJU40520 Revers e system W ARNI NG EWJ0123 0 ● Do not use the reverse function to slow down or stop the watercraft as it could cause you to lose contr ol, be ejected, or impact the handlebars.
Watercraft operation 38 EJU40000 Watercraft operation modes EJU41960 Low RPM Mode The Low RPM Mode is a function tha t limits the maximum engine s peed to approximately 70% of the maximum engine speed in the nor- mal mode.
Watercraft operation 39 “ L-MODE ” indicator light will come on when the engine is started. To deactivate the Low RPM Mode: Push the “ L-Mode ” (unlock) button on the re- mote control transmitter for more than 4 sec- onds.
Instrument operation 40 EJU41850 Multifunction information cent er The multifunction information center disp lays various watercraft information. Multifunction information center initial op- eration When the multifunction information center is activated, all of the display segments and the “ SECURITY ” indicator light come on.
Instrument operation 41 To switch the speedometer display units: Push the select button for at least 1 second, within 10 seconds after the multifunction infor- mation center is activ ated. The speedometer display changes. EJU31463 Tachometer The tachometer shows the e ngine speed.
Instrument operation 42 When the battery voltage i s normal, the volt- meter displays approxim ately 12 volts. If the battery voltage has dropped s ignificant- ly, “ LO ” is d isplayed on the voltm eter. If the battery voltage has risen si gnificantly, “ HI ” is displayed.
Instrument operation 43 TIP: Push the select button on the multifunction in- formation center to stop the buzzer. EJU31626 Oil pressure warning If the oil pressure dro ps significantly, the oil pressure warning indicator and the “ WARN- ING ” indicator light blink, and the buzzer sounds intermittently.
Instrument operation 44 EJU31634 Check engine warning If a sensor malfunction or a sho rt circuit is de- tected, the check engine warning indica tor and the “ WARNING ” indicator light b link, and the buzzer sounds intermittently .
Equipment operation 45 EJU40333 Equipment EJU31036 Seat The seat is removable. Remove the seat to a ccess the engine com- partment. VXS: VXR: To remove the seat: (1) Pull the seat latch up, and then lift up the rear of the seat. (2) Pull the seat rearward and remove it.
Equipment operation 46 (2) Push the rear of the seat dow n to secure- ly lock it in place. EJU31363 Handgrip The handgrip is us ed when boarding the wa - tercraft from the water and w hen the spotter is facing rearward. WARNING! Do not use the handgrip to lift the water craft.
Equipment operation 47 towing it in an emergency. (See page 95 for information on towing the watercraft.) EJU34881 Ster n eyes The stern eyes are used to attach a rope to the watercraft when transporting or mooring it. EJU40420 Cleat The cleat is used to attach a ski rope to the watercraft when pulling a water-skier.
Equipment operation 48 To open the bow storage comp artment: Pull the hood latch up, and then lift up the rear of the hood. To close the bow storage compartment: Push the rear of the hood down to se curely lock it in place.
Equipment operation 49 To open the glove compartment: Slide the glove compartment latch toward you, and then lift up the lid. To close the glove compa rtment: Push the lid down to securely lock it in pl ace. EJU41420 Beverage holder (VXR) The beverage holder is located in the glove compartment.
Equipment operation 50 To use the fire ex tinguisher holder and co ver: (1) Pull the ho od latch up, and then lift up the rear of the hood. (2) Unhook the ba nd and remove the fire ex- tinguisher cover. (3) Place the fire extinguisher in the holder, and then p lace the cov er over the fire ex- tinguisher.
Operation and handling re quirements 51 EJU31822 Fuel requirements EJU37165 Fuel W ARNI NG EWJ0028 2 ● Gasoline and gasoline vapors are ex- tremely flammable. To avoid fires and explosions and to reduce the risk of in- jury when refueling, follow these in- structions.
Operation and handling requirements 52 (6) Stop filling when the fuel level reaches approximatel y 50 mm (2 in) from the top of the fuel tank. Do not overfill the fuel tank. Because fuel expands when it heats up, heat from the en gine or the sun can cause fuel to spil l out of the fuel tank.
Operation and handling re quirements 53 (3) Remove the dips tick and wipe it clean. (4) Insert the dipstick back into the dipstick tube completely . Remove the dips tick again and make s ure that the engine oil level is between the minim um and maxi- mum level marks .
Operation and handling requirements 54 EJU40021 Draining the bilge water NOT ICE ECJ01301 Do not run the engine at full throttle when bilge water remains in the engine compart- ment. The bilge water can splash into the engine, which can result in severe dam- age.
Operation and handling re quirements 55 engine, which can result in severe dam- age. [ECJ 00553] EJU33464 Transporting on a trailer When transporting the watercraft on a trailer, secure the tie downs to the trailer through the bow eye and stern eyes.
First-time operation 56 EJU36665 Engine break-in NOT ICE ECJ00431 Failure to perform the engine break-in could result in reduced engine life or even severe engine damage. The engine break-in is ess ential to allow the various compon ents of the engine to wear and polish th emselves to the correct operat- ing clearances.
Pre-operation checks 57 EJU31981 W ARNI NG EWJ0041 1 Failure to inspect or maintain the w atercraft properly increases the possibility of an ac- cident or damage to the watercraft.
Pre-operation checks 58 TIP: To ensure safety and reliability, pre-operation checks should be made each time the watercraft is used. Seat Check that the seat is securely installed. 45 POST -LA UNCH CHECKS Cooling water pilot outlet Check that water is discharged f rom the cooling wa- ter pilot outlet while the engine is r unning.
Pre-operation checks 59 EJU32281 Pre-operation check points EJU40545 Pre-lau nch c hecks Perform the pre-launch checks in the pre-op- eration checklist while the watercraft is on land. To perform the pre-launch checks: (1) Remove the seat. (See page 45 for seat removal and installation procedures.
Pre-operation checks 60 the dipstick. (See page 52 for information on checking the e ngine oil level.) EJU32455 Bilge water check Make sure that no bilge water has c ollected in the engine compartment. If bilge water has collected in the engine compartment, drain it.
Pre-operation checks 61 whole range, a nd that the free pla y is not ex- cessive. Turn the handlebars as far as possible to the right and left to make sure that the jet thrust nozzle moves as the handlebars are turned, and that there is no difference between the right and left fully turned positions of the jet thrust nozzle.
Pre-operation checks 62 Operate the sh ift lever several times to make sure that operation is smooth thr oughout the whole range. Also, mak e sure that the reverse gate moves up and down acc ording to the op- eration of the shift lever and that the gate makes contact with the stoppers.
Pre-operation checks 63 yard) may not pull free when the operator falls off, allowing the watercraft to contin- ue to run and cause an accident. [EWJ01220] EJU32675 Switch checks NOT ICE ECJ01310 Do not run the engine over 4000 r/min on land.
Pre-operation checks 64 EJU32533 Fire extinguisher check Check that there is a full fire e xtinguisher on board. To check the fire extinguisher, see the instruc- tions supplied b y the fire extinguish er manu- facturer. Always keep the fire extinguisher secured in the holder with its c over in place.
Pre-operation checks 65 EJU41440 Hood check Push down on the rear of the hood and make sure that it is securely closed. EJU40144 Post-launch checks Perform the post-launch c hecks in the pre-op- eration checklist w hile the watercraft is in the water and the engine is running.
Operation 66 EJU32902 Operating your watercraft W ARNI NG EWJ0051 0 Before operating your w atercraft, become familiar with all of the controls. Consult a Yamaha dealer about any control or func- tion that you do not fully understand. Fail- ure to understand how the controls work could cause an accident or prevent you from avoiding a n accident.
Operation 67 EJU40210 Riding position Operator riding position The operator should grip the handlebars firm- ly with both hands and s it astride the seat with both feet on the floor of the footwell.
Operation 68 is attached correctly. If the engine shut-off cord (lanyard) is not attached correctly, it may not pull free when the operator falls off, allowing the water- craft to continue to run and cause an accident. [EWJ 00581] (4) With the throttle lever relea sed, push the start switch (green button) to start the en- gine.
Operation 69 is in the fully clos ed (idle) position. (See page 37 for information on operating the shift lever.) EJU33254 Turning the watercraft W ARNI NG EWJ0077 1 ● Do not release the throttle lever when trying to steer away from objects — you need throttle to steer .
Operation 70 slows down, the watercraft will no longer respond to handlebar input until you ap- ply throttle again or you reac h trolling speed. At trolling speed, the watercraft can be turned gradually by handlebar position alone using just the am ount of thrust available at idle.
Operation 71 objects, and other watercraft to give you time to stop. ● Do not shut the engine off when slowing down in case you need engine power to steer away from a boa t or other obstacle that comes into your path.
Operation 72 yourself up, an d then grasp the handgrip with one hand. (2) Pull yourself up to a kneeling po sition on the boarding platform, and the n move to the seat and sit astride. (3) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch.
Operation 73 (4) Have the first passenger move to the rear of the watercraft. (5) Have the first p assenger board using the same procedure as the operator, place their feet on the floor of the f ootwell, and securely hold on to the operator. (6) Have the second pa ssenger follow the same procedure.
Operation 74 (4) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch. (5) Look in all directions, and then start the engine and operate at trolling speed. (6) Have the s econd passenger pull them - selves up onto the b oarding platform into a kneeling position and balance there.
Operation 75 the watercraft, otherwise pebbles or sand could be sucked into the jet intake, caus- ing impeller damage and engine overheat- ing. EJU40232 Starting off from a trail er (1) Launch the watercraft and mo ve the shift lever to the reverse position.
Operation 76 craft over counterclockwise, otherwise water can enter the engine, which can result in severe damage. [ECJ005 41] (3) Start the engine and operate the water- craft at planing speed to dra in the bilge water from the engin e compartment. (See page 54 for information on draining the bilge water.
Operation 77 weeded areas is unavoidable, alternately squeeze the throttle lever and relax your grip on the throttle lever to v ary the engine speed. Weeds tend to become clogged m ore when operating at a steady speed and at trolling speed. If weeds m ay have clogged the intake area, clean the jet intake.
Care and storage 78 EJU37145 Post-operation care W ARNI NG EWJ0033 0 Always place the watercraft upright in a horizontal position when storing it, other- wise fuel could leak out into the engine or engine compartment, which could create a fire hazard.
Care and stor age 79 flows out continually from the jet thrust nozzle. (7) Run the engine at idling speed for about 3 minutes watchi ng the engine condition. If the engine stops w hile flushing, turn the water supply o ff immediately and perform the procedure again from step 6.
Care and storage 80 Eyes: Flush with w ater for 15 minutes and get prompt medical attention. Batteries produce e xplosive gases. Keep sparks, flames, cigarettes, etc., well away. If using or charging the battery in an en- closed space, make sure that it is well ven- tilated.
Care and stor age 81 To store the battery: (1) Clean the battery cas e using fresh water. (2) If the battery terminals are dirty or corrod- ed, clean them using a wire brush. (3) Apply YAMALUBE MARINE GREASE to the battery terminals . (4) Store the battery in a cool , dry place.
Care and storage 82 EJU33492 Long-term storage W ARNI NG EWJ0033 0 Always place the watercraft upright in a horizontal position when storing it, other- wise fuel could leak out into the engine or engine compartment, which could create a fire hazard.
Care and stor age 83 ● Shift cable (reverse gate end) EJU40261 Rustproofing Spray metallic parts of the hull, deck, and en- gine with a rust inhibitor such as Yamaha Sil- icone Protectant and Lubric ant. Have a Yamaha dealer rustproof the internal engine compo nents.
Maintenance 84 EJU33757 Maintenance Periodic checks an d lubrication will k eep your watercraft in the safest and most efficient con - dition possible. Therefore, make sure to carry out the periodic m aintenance. Safety is an ob- ligation of the watercraft owner.
Maintenance 85 (3) Lift up the engine cover and remov e it. To install the engine cover: (1) Place the engine cover in its original posi- tion, and then push it do wn. (2) Install the engi ne cover screws, and then tighten them to the specified torque.
Maintenance 86 EJU37062 Periodic maintenance chart The periodic maintenanc e chart gives general guide lines for periodic maintenanc e. Have a Yamaha dealer perform the checks in the foll owing chart. However, maintenance may need to be performed more frequently depending on your operating co nditions.
Maintenance 87 EJU36942 Engine oil an d oil filter W ARNI NG EWJ0034 0 Engine oil is extremely hot immediately af- ter the engine is turned off. Coming in con- tact with or getting any engine oil on your clothes could result in burns.
Specifications 88 EJU34542 Specificatio ns Watercraft capacity: Maximu m peo ple on bo ard: 3 pers on Maximu m load capacit y: 240 kg ( 530 lb) Dimensions: Length: VXS 3220 mm (126.8 i n) VXR 3 270 mm ( 128.7 in) Width: 1170 mm (46. 1 in) Height: 1160 mm (45.
Trouble recovery 89 EJU34561 Troubleshooting If you have any trouble with your watercraft, use the troub leshooting chart to check for th e pos- sible cause. If you cannot find the cause, cons ult a Yamaha dealer. EJU34595 Troubleshooting chart Confirm the possible cause and rem edy, and then refer to the applicable page.
Trouble recove ry 90 Engine runs irregu- larly or stalls Fuel E mpty Refill as soon as pos- sible 51 Stale or contaminat- ed Hav e ser viced by Y amaha dealer — Fuel tank Water or dir t present Hav .
Trouble recovery 91 Wat erc r af t sl o w o r loses power W atercraft operation mode Low RPM mode acti- vat ed Deactivate Lo w RPM Mode 38 Cavitation Jet intake clogged Clean 92 Impeller damaged or wo.
Trouble recove ry 92 EJU34623 Emerge ncy procedure s EJU34634 Cleaning the je t intake a nd impeller W ARNI NG EWJ0078 2 Before attempting to remove weeds or de- bris from the jet intake or impeller area, shut the engine off and remove the clip from the engine shut-off switch.
Trouble recovery 93 (2) Remove any weeds or debris from around the jet intake, drive shaft, impel- ler, jet pum p housing, and jet thrus t noz- zle. If debris is difficult to remove, consult a Yamaha dealer.
Trouble recove ry 94 (2) Remove the electric al box cover. (3) Loosen the cap on the electrical box and remove it. (4) Replace the blown fuse with the spare fuse of the correct amperage by using the fuse puller on the reverse side of the cap. WARNING! Do not use fuses of a dif- ferent amperage than recommended.
Trouble recovery 95 (7) Securely instal l the seat in its original po- sition. If the fuse immedia tely blows again, the elec- trical system may be defective.
Consumer information 96 EJU34781 Limited warranty Y AMAHA MOTOR CORPORATION, U.S.A. W ATERCRAFT LIMITED WARRANTY Y amaha Motor Corporation is proud of its heritage and reputation for producing products with high standards of quality and workman- s hip.
Consumer information 97 THIS W ARRA NTY GIVES Y OU SPECIFIC LEGAL RIGHTS, AND Y OU MA Y ALSO HA VE OTHER RIGHTS WHICH V AR Y FROM ST A TE T O ST A TE. Y AMAHA M O T OR CORPORA TION, U.S.A. P ost Office Bo x 6555 Cypress, Calif ornia 90630 W ARRANTY QUESTIONS AND ANSWER S Q.
Consumer information 98 EJU34801 YAMAHA EXTENDED SERVICE (Y.E.S.) K eep your Y amaha protected ev en after your warranty expires with gen uine Y am aha Extended Service (Y .E.S.). • Y .E.S. is designed and administere d by Y a maha Motor Cor poration to provide maximum owner satisf action.
Index A After removin g the watercraft from the water ............ ................ ................. ........ 77 Approval lab el of emission cont rol certificate ..................... ................. .......... 2 B Battery ca re ................ ..
Index Long-term storage ....................... ............. 82 Low RPM Mo de..................... ................. .. 38 Lubricat ion.................. ................. ............. 82 M Main co mponents , location o f .......... ........ 27 Mainten ance.
UF2M11E0.book Page 3 Monday, July 11, 2011 10:21 AM.
EJU42010 F or your best o wnership experience, think Gen uine Y amaha! Genuine Y amaha Parts – Genuine Y amaha replacement par ts are the exact same par ts as the ones or iginally equipped on your v ehicle, providing y ou with the perf or mance and durability y ou hav e come to e xpect.
Printed in USA August 2011–0.8 × 1 CR DIC183.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Yamaha VXR è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Yamaha VXR - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Yamaha VXR imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Yamaha VXR ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Yamaha VXR, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Yamaha VXR.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Yamaha VXR. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Yamaha VXR insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
