Manuale d’uso / di manutenzione del prodotto SCX364 del fabbricante Windsor
Vai alla pagina of 35
Read these instructions before using the m achine MODELS: SCX364 10052410 Operating Instructions (ENG) Instrucciones de funcionamiento (SPA) 86037150 02/20/09 PRV NO.
MACHINE DATA LOG/OVERVIEW SCX364 86037150 1/17/07 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: ____________________ ___________________________________ _____.
TABLE OF CONTENTS SCX364 86037150 3/14/07 3 Machine Data Log/Overview. ........................ 2 Table of Contents ......................................... 3 HOW TO USE THIS MANUAL How to use this Manual. ............................... 1-1 SAFETY Important Safety Instructions .
HOW TO USE THIS MANUAL SCX364 86037150 1/17/07 1 - 1 This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
SCX364 86037150 1/17/07 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors.
HAZARD INTENSITY LEVEL SCX364 86037150 1/17/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY.
SAFETY LABEL LOCATION SCX364 86037150 1/17/07 2-3 NOTE: These drawings indicate the location of safet y labels on the machine . If at any time the labels becom e illegible, promptly replace them. 2% GRADE WARNING CIRCUIT BREAKER DECAL 86243530 PRV NO.
TECHNICAL SPECIFICATIONS SCX364 86037150 1/17/07 3-1 ITEM DIMENSION/CAPACIT Y Nominal power 1440 Watts Rated Voltage 24VDC Rated Amperage 60 Amps Batteries 4 X 6 Volt 250-305-335AH @ 20 hr rate Scrub Brush Motors .33 hp (0.25 Kw) Vacuum Motor .75 hp (0.
TECHNICAL SPECIFICATIONS SCX364 86037150 1/17/07 3-2 ITEM MEASURE Height 45 in. (114 cm) Length with 36 in. (90 cm) scrub head 72 in. (183 cm) Width without squeegee and scrub head 24 in. (61 cm) Width of squeegee for 36 in. (90 cm) scrub head 35 in. (89 cm) Width of scrub path for 36 in.
HOW THE MACHINE WORKS SCX364 86037150 1/17/07 3-3 The Saber Cutter is a battery powered, self- propelled, hard floor scrubber intended fo r commercial use. The appliance applies a clea ning solution onto a hard floor, scrubs the floo r with brushes, and then vacuum s the soiled water back into the recovery tank.
COMPONENTS SCX364 86037150 1/17/07 3-4 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain H ose 5. Scrub Head Fixed 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9. Solu tion Stra iner 10. Rear Squeegee 11. Top Cover 12.
CONTROLS SCX364 86037150 1/17/07 3-5 4 10 11 12 14 15 8 7 6 3 13 16 1 9 5 2 17.
CONTROLS SCX364 86037150 1/17/07 3 - 6 1. Key Switch 2. Emergency Shut Off Switch (Optional) 3. Speed Control Knob 4. Propel Control Lever 5. Reverse Button 6. Brush Switch 7. Actuator Switch Deck Up-Down 8. Solution Control Knob 9. Vacuu m Switch 10.
CONTROLS SCX364 86037150 1/17/07 3-7 7. ACTUATOR SWITCH DECK UP-DOWN Adjusts the amount of brush pressure to the floor by raising or lowering the scrub d eck. Use the brush pressure indicator to determin e the correct pressure. To increase brush pressure, press the bottom of the switch.
CONTROLS SCX364 86037150 1/17/07 3-8 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batterie s. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged.
MACHINE OPERATION SCX364 86037150 1/17/07 3-9 PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possi ble problems that could cause poor perf ormance or lost time from breakdown. Follow the same pro cedure each time to avoid missing steps. NOTE: See maintenance section for pre-run machine inspection che cklist items.
MACHINE OPERATION SCX364 86037150 1/17/07 3-10 NORMAL SCRUBBING Plan the scrubbing pattern in advance. The long est track is around the perimeter of the area to be cleaned. For efficient operation, the runs should b e the longest possible without turning, stopping, or raising and loweri ng scrub deck/squeegee.
MACHINE OPERATION SCX364 86037150 1/17/07 3-11 DOUBLE SCRUB For floors which are heavily soiled or h ave thick accumulations of floor finish may not clean sufficiently with one pass.
MAINTENANCE SCX364 86037150 1/17/07 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY 100 HRS 200 HRS Check batteries after cha rging; add water if necessary * Check pad wear to prevent buildup of.
MAINTENANCE SCX364 86037150 1/17/07 4-2 1. Batteries 2. Rear Squeegee 3. Scrub Brushes 4. Float Shut-Off 5. Solution Strainer 6. Brush Motor 5 7 2 8 4 1 11 12 9 3 10 13 6 7. Traction Motor 8. Circuit Breakers 9. Scrubhead Fixed and Swinging 10. Vacuum Motor 11.
MAINTENANCE SCX364 86037150 1/17/07 4-3 1. BATTERIES The batteries provide the power to ope rate the machine. The batteries require regul ar maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times.
MAINTENANCE SCX364 86037150 1/17/07 4-4 CHECKING BAT TERY SPECIFIC GRAVITY Use a hydrometer to chec k the battery specific gravity. CHECKING GRAVITY A. Hydrometer B. Battery NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, the readi ng m ay not be accurate.
MAINTENANCE SCX364 86037150 03/14/ 07 4-5 FOR SAFETY: When charging, conne ct the charger to the batteries before conne cting the charger to the AC wall outlet. Never connect the charger to the AC wall outlet first. Hazardous sparks may result. 7 . Plug the charger connector into the battery connector.
MAINTENANCE SCX364 86037150 1/17/07 4-6 2. REAR SQUEEGEE The front blade allows solution to pass through channels in the blade into the squeeg ee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces an d can be rotated for extended life.
MAINTENANCE SCX364 86037150 1/17/07 4-7 TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeege e and drive forward at least 2 feet (60cm.). 2. With the squeegee down, stop the machine. Do not allow machine to roll back.
MAINTENANCE SCX364 86037150 1/17/07 4-8 3. SCRUB BRUSHES There are four different types of brushes available to cover applications from cle aning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market.
MAINTENANCE SCX364 86037150 1/17/07 4-9 5. SOLUTION STRAINER The solution strainer is located in front of the left front wheel. The solution strainer protect s the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris.
MAINTENANCE SCX364 86037150 1/17/07 4-10 7. TRACTION MOTOR Do not use a pressure washer to clean around the motors. Use tap pressure only . TRACTION MOTOR CARBON BRUSH REPLACEMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remove key.
MAINTENANCE SCX364 86037150 1/17/07 4-11 10. VACUUM MOTOR (Refer to the Vacuum Group in the parts se ction of manual) Do not use a pressure washer to clean around the vacuum motors. Use tap pressur e only. Care must be taken so that water is not directed into vacuum motor air intakes.
MAINTENANCE SCX364 86037150 1/17/07 4-12 11. ACTUAT O R SCRUB DECK UP- DOWN REMOVAL/REPLACEMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If opti on is installed). 1. Remove front cover.
MAINTENANCE SCX364 86037150 1/17/07 4-13 13. FRONT SQUEEGEE The front blade allows solution to pass through channels in the blade into the squeeg ee assembly while maintaining vacuum to provide lift. The front blade has two wear surfac es an d can be rotated for extended life.
MAINTENANCE SCX364 86037150 1/17/07 4-14 TO ADJUST FRONT SQUEEGEE DEFLECTION 1. Choose a smooth, level surface. Lowe r the front squeegee and deck and drive forwa rd at least 2 feet (60cm) until the desired brush pressure is obtained. 2. With the squeegee down, stop the machine.
MAINTENANCE SCX364 86037150 1/17/07 4-15 RECOMMENDED GREASIN G: 1-2 strokes of Mobiltemp ® 78 or compatible clay- based or calcium-based grease..
MACHINE TROUBLESHOOTING SCX364 86037150 1/17/07 4-16 PROBLEM CAUSE SOLUTION Poor or no water pick-up on either squeegee Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debr.
MACHINE TROUBLESHOOTING SCX364 86037150 1/17/07 4-17 PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or set too low Turn .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Windsor SCX364 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Windsor SCX364 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Windsor SCX364 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Windsor SCX364 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Windsor SCX364, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Windsor SCX364.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Windsor SCX364. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Windsor SCX364 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
