Manuale d’uso / di manutenzione del prodotto 1230 del fabbricante Wilton
Vai alla pagina of 32
Part No. 9078241 Revision A Radial Ar m Drill Pr ess Model 1230 Operating instr uctions and par ts manual.
.
3 T able of Contents Cover Page ........................................................................................................................ 1 General Specifications .........................................................................
4 Column diameter 1 1 13/16 in. (295mm) Column to spindle center distance, max. 46 in. (1 150mm) Column to spindle center distance, min. 13 3/8 in. (334mm) Spindle travel along arm, total 35 in. (875mm) Base surface to spindle end, max. (no tooling) 54 in.
5 -Always shut off the machine when not in use. When servicing machine: -Always unplug machine from electrical power while servicing. -Always follow instructions in operators and parts manual when changing accessory tools or parts. -Never modify the machine without consulting Wilton Corporation.
6 240 volt lines 120 volt lines 0-50 feet No. 14 No. 14 50-100 feet No. 14 No. 12 Over 100 feet No. 12 No. 8 Conductor length A WG (American wire gauge) number attachment to do a job it was not designed for . 16. Use only recommended accessories and follow manufacturers instructions pertaining to them.
7 Operating Instr uctions Clamping workpieces to the machine Both the box table and the base surface are slotted to accept a suitably sized T-slot clamp.
8 Inserting tooling The Model 1230 uses a #4 Morse taper in the spindle to secure tooling. Any drill, milling cutter , or tool holder with a #4MT can be inserted into the quill.
9 on LOW or HI speed. There is a chart on the front of the drill head which shows you the spindle speeds available and the gear change lever and motor switch values required to select each speed. See Fig. 1. On the gear change table you will also find the recommended drill sizes for the various speeds which are selectable.
10 pushed inward -- on pivots which are in the feed lever hub. When the feed levers are pushed toward the drill head, the power feed mechanism is disengaged.
11 Spindle direction and power feed The spindle can be driven clockwise or counter- clockwise. The direction of rotation is controlled by the control lever on the left hand side of the drill head.
12 Resetting the STOP switch 1. T urn the switch in the direction of the arrow on the red button -- clockwise. The switch is reset and the other spindle motor controls can be used. Using the control lever The four-position control lever is located on the left hand side of the drill head console.
13 release it. Rather , the lever stays in the position in which you put it when you are controlling the spindle. There is no need to hold it in position to keep the spindle running. All of these functions are clearly labeled on the plate which surrounds the control lever and boot.
14 1. Lift the drill press from its shipping skid according to the diagram, below . 2. Secure the drill press to the floor The drill press MUST be anchored to the floor according to the layout diagram below .
15 to the ON position. 6. Observe the direction of rotation of the coolant pump. Y ou can see the pump shaft rotate on top of the pump at the rear of the drill press. There will be an arrow cast into the pump, and the shaft should be rotating in the direction of the arrow .
16 Figure 6: Wiring diagram.
17 Replacement Parts This section provides exploded view illustrations that show the replacement parts for the Wilton 4 foot arm, Model 1230 Radial Drill.
18 Exploded View - Column and Base.
19 Parts List - Column and Base 1 523291 1 Base 2 5232921 Bolt 3 5232931 Needle bearing 4 5232941 Internal column 5 5232951 Bolt 6 5232961 T op bearing cover 7 5232971 Thrust bearing 8 5232981 Fixed brg.
20 1 5235751 Bolt 2 5235761 W asher 3 5235771 Bushing 4 5235781 Round bar 5 5235791 Plain washer 6 523581 1 N u t 7 5235821 N u t 8 5235831 Bolt 9 5235841 Chain frame 10 5235851 Screw 1 1 5235861 Limit switch 12 5235871 Retaining ring Ref no. Wilton part no.
21 1 523331 1 Lamp cover 2 5233321 Screw 3 5233331 Lamp 4 5233341 Lamp seat 5 5233351 Arm rack 6 5233361 Bolt 7 5233371 Arm 8 5233381 Locking shaft 9 5233391 Oil fill cup 10 523341 1 Fixed clamping block Ref no.
22 Exploded View - Arm (Rear).
23 Parts List - Arm (Rear) 50 5236551 Bolt 51 5236561 Gear 52 5236571 Block 53 5236581 Block 54 5236591 Bolt 55 523661 1 Rack shaft 56 5236621 Rack 57 5236631 Bolt 58 5236641 Block 59 5236651 Shaft 60.
24 Parts List - Riser Mechanism Ref no. Wilton part no. Description 1 5232451 Motor 2 5232461 K ey 3 5232471 Screw 4 5232481 Adapter 5 5232491 Plastic sheet 6 523251 1 Screw 7 5232521 Adapter 8 523253.
25 Exploded V iew - Head.
26 Parts List - Head 1 5233551 Hand wheel lock nut 2 5233561 Hand wheel 3 5233571 Plastic knob 4 5233581 Feed handle 5 5233591 Pi n 6 523361 1 Clutch housing 7 5233621 Stopper cotter 8 5233631 Spring .
27 109 5234751 Oil level gage 1 10 5234761 Gear box 1 1 1 5234771 Gear 1 12 5234781 Spring 1 13 5234791 Steel ball 1 14 523481 1 Sleeve 1 15 5234821 Worm gear sleeve 1 16 5234831 Worm gear 1 17 523484.
28 Parts List - Rear of Head 1 523541 1 Bolt 2 5235421 Eccentric shaft 3 5235431 Gear box 4 5235441 Bolt 5 5235451 Adjustable collar 6 5235461 Adjustable collar 7 5235471 Bearing bracket 8 5235481 Cam.
Parts list - Flood Coolant System Ref no. Wilton part no. Description Ref no. Wilton part no. Description 1 5232251 Fixed blade 2 5232261 Cross screw 3 5232271 Hose 4 5232281 HH Screw 5 5232291 Coolan.
30 Notes:.
.
Wilton Corporation 300 South Hicks Road Palatine, IL 60067 TEL: 1-888-594-5866 F AX: 1-800-626-9676.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Wilton 1230 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Wilton 1230 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Wilton 1230 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Wilton 1230 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Wilton 1230, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Wilton 1230.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Wilton 1230. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Wilton 1230 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
