
This guide is for experienced HP Support Center personnel and reseller technicians. They have already completed the HP Vectra PC family training course, or equivalent, and have at least six months of experience servicing HP Vectra PCs.
It is a self-paced training guide designed to train you to install, configure, and repair the HP Vectra 500 Series PC (models 520 and 525), introduced as of Q3 1996. You can follow it without having any equipment available.

Models 520 and 525

The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
This document contains propriety information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company.
AdobeTM is a trademark of Adobe Systems Incorporated which may be registered in certain jurisdictions. CompuServeTM is a U.S. trademark of CompuServe, Inc. Microsoft®, MS-DOS® and Windows® are U.S. registered trademarks of Microsoft Corporation. Pentium® is a US registered trademark of Intel Corporation. Lotus® is a U.S. registered trademark of Lotus Development Corporation. All other trademarks and copyrights are property of their respective owners.
Hewlett-Packard France Grenoble Personal Computer Division Technical Marketing 38053 Grenoble Cedex 9 France
©1996 Hewlett-Packard Company


Overview 24
Software Packages 26
Software Recovery 30
MicroCom Carbon Copy 30 HP Vectra PC Checkup 31 Service Handbook 31
Running the HP Vectra PC Checkup 32
Generating an HP Vectra PC Checkup Disk from Within Windows 95. . 32 Generating an HP Vectra PC Checkup Disk from the Product Recovery CD-ROM 32 Running the HP Vectra PC Checkup from a Floppy Disk 32 Running the HP Vectra PC Checkup from the Hard Disk 32
iv English

After reading this chapter you will be able to describe features specific to HP Vectra 500 Series PCs (models 520 and 525).

1 Product Overview and Comparisons Product Overview
This section describes the HP Vectra 500 Series PCs (models 520 and 525) by highlighting their main features, accessory and mass storage capabilities, and common features.
For information regarding the Q3 1995 collection of Vectra 500 Series PCs, refer to the Familiarization Guide for that collection (part number D37xx + 49A-90001). For information regarding the Q1 1996 collection of Vectra 500 Series PCs (models 510 and 515), refer to the Familiarization Guide for that collection (part number D4110-90901).
The naming convention used by Vectra 500 Series PCs (models 520 and 525) is demonstrated in the following example:
1st Field 2nd Field 3rd Field
where:
1st Field 5 indicates “Vectra 500 Series” 2 indicates 2nd generation 0 indicates desktop. 5 indicates minitower
2nd Field Nothing for standard models CD for models equipped with a CD-ROM drive MCx for advanced multimedia and communications models
3rd Field 5 indicates Pentium Second number indicates processor speed: 120, 133, 166 and 200 MHz
There have been three releases of HP Vectra 500 Series PCs. They are:
Q3 1995 502, 510, 512, 514, 522, 560, 562, 564, 572, 574 Q1 1996 510 and 515 Q3 1996 520 and 525

1 Product Overview and Comparisons Product Overview
Main Features of the HP Vectra 500 Series PCs (models 520 and 525)
Supplied & Max Available
Supplied & Max Memory
2nd-Level Cache in KB
1 AE=All Europe, LA=Latin America, NA=North America, APP=Asia / Pacific Partner, B=Brazil, C=China, I=India 2 There are three system board options for models 520 and 525: Type A = Part Number D4051-63001, Type B = Part Number D3657-63001, and Type C = Part Number D3661-63001. 3 There are three video options for models 520 and 525, corresponding to the three system board types: UMA = Unified Memory Architecture (shared main and video memory), Integrated = video controller and memory on the system board, Matrox = Matrox MGA Millennium video card.

1 Product Overview and Comparisons Product Overview
Supplied & Max Memory
Supplied & Max Available
2nd-Level Cache in KB
1 AE=All Europe, LA=Latin America, NA=North America, APP=Asia / Pacific Partner, C=China, I=India, K=Korea 2 There are three system board options for models 520 and 525: Type A = Part Number D4051-63001, Type B = Part Number D3657-63001, and Type C = Part Number D3661-63001. 3 There are three video options for models 520 and 525, corresponding to the three system board types: UMA = Unified Memory Architecture (shared main and video memory), Integrated = video controller and memory on the system board, Matrox = Matrox MGA Millennium video card

1 Product Overview and Comparisons Product Overview
Accessory and Mass Storage Capabilities
1 In all models, one front-access bay is occupied by a 3.5-inch floppy disk drive. In models 520CD 5/xxx, 520MCx 5/xxx, 525CD 5/xxx and 525MCx 5/xxx an additional front-access bay is occupied by the CD-ROM drive.
The following features are common to all PCs in the HP Vectra 500 Series PC range:
Common Features

1 Product Overview and Comparisons Model Comparisons
HP Vectra 500 Series PCs are Pentium-processor, ISA/PCI-based PCs, housed in desktop and minitower casings. The series is targeted at the Small Business Small Office (SBSO) market.
There are three system board options for models 520 and 525. The three options can be referred to as Type A, Type B and Type C.
Type A (part number D4051-63001) is a new system board which incorporates a technology known as Unified Memory Architecture (UMA). Using UMA, there is no dedicated video memory. Instead, a portion (1 MB or 2 MB) of main memory is shared as video memory. Refer to Chapter 2 for more information about this system board.
Type B (part number D3657-63001) is the same as the system board used in the Q1 1996 collection (models 510 and 515).
Type C (part number D3661-63001) is used for one product only. This board is the same as the Type B board but without the onboard video controller and memory. Video control and memory is obtained using a Matrox MGA Millennium video card.
There are two backplane options for models 520 and 525—one for the desktop and one for the minitower. The two backplanes are the same as those used in the Q1 1996 collection (models 510 and 515).
There are two casing options for models 520 and 525—one for the desktop and one for the minitower. The two backplanes are the same as those used in the Q1 1996 collection (models 510 and 515).
With high speed processors (166 MHz and above), an air flow guide is required to help the fan dissipate the heat from the processor. On desktop models, a special power supply unit integrates the fan over the processor.

After reading this chapter you will be familiar with the HP Vectra 500 Series PC (models 520 and 525) casing and hardware assembly.

2 Casing, System Boards and Video Desktop and Minitower Casing
The casing for models 520 and 525 is the same as that for the Q1 1996 collection (models 510 and 515).

2 Casing, System Boards and Video System Board, Switches and Jumpers
As mentioned in Chapter 1, there are three system board options for models 520 and 525. This section describes the Type A system board (part number D4051-63001).

CD-ROM Connector (IDE Channel 2) HDD Connector (IDE Channel 1)
System Board Layout

2 Casing, System Boards and Video System Board, Switches and Jumpers
System Board Switches and Jumpers
This section indicates the switches and jumpers used to modify the system settings.
This switch is multi-purpose and is used to modify BIOS, CMOS and password settings.
Switch Default Setting OFF ON COMMENTS
1 OFF Flashing Enable Flashing Disable Updating the BIOS. Set the security mode. Set the switch to the ON position to prevent the BIOS from being upgraded.
2 OFF CMOS is in normal operation
CMOS Clear To clear the CMOS configuration. Set the switch to the ON position and restart the PC. Return the switch to the OFF position and restart the PC to return to normal operation.
3 OFF Password is in normal operation
Password Clear To clear the password. Set the switch to the ON position and restart the PC. Return the switch to the OFF position and restart the PC to return to normal operation.
This switch is used to select the CPU Bus Frequency / CPU Frequency ratio.
The following table includes some examples of the settings to use for different processor speeds. (Jumper J7 settings are also shown. This jumper is described on the next page.)
Processor Speeds Switch Block SW2
Ratio 1 2 CPU Bus Frequency Pins Shorted
CPU Frequency 133 MHz 1 / 2 ON OFF 66 MHz 3 - 4
CPU Frequency 150 MHz 2 / 5 ON ON 60 MHz 1 - 3
CPU Frequency 166 MHz 2 / 5 ON ON 66 MHz 3 - 4

2 Casing, System Boards and Video System Board, Switches and Jumpers
CPU Bus Frequency Jumper (J7)
This jumper sets the CPU bus frequency. The following figure shows the possible settings.

This jumper selects the cache type—either synchronous or asynchronous. The default setting is for synchronous cache. The following figure shows the two settings.

Space-bar Power-on Feature Jumper (JP4)
The Space-bar Power-On feature (“KBD Start” on the system board) enables the PC to be turned on using the spacebar. To enable this feature, a jumper has to be inserted. This setting overrides the setting in the Setup program.

Cache Jumper (J6)

2 Casing, System Boards and Video Video Options
With models 520 and 525 there are three video options:
Video Controller and Video Memory on the System Board
This option is the same as the video option in the Q1 1996 collection (models 510 and 515). That is, 1 MB of video memory as standard on the system board which can be upgraded to 2 MB by installing two memory chips of 512 KB each.
The following video resolutions are typically available.
Resolution Number of colors Refresh Rate (Hz) Memory
640 x 480 16 60 1 MB
640 x 480 256, 64K 60, 72, 75
800 x 600 256, 64K 56, 60, 72, 75
1024 x 768 256 i431 60, 70, 75
640 x 480 16 60 2 MB
640 x 480 256, 64K, 16M 60, 72, 75
800 x 600 256, 64K, 16M 56, 60, 72, 75
1024 x 768 256, 64K i431, 60, 70, 75
1280 x 1024 256 i451, 60, 72, 75
1 Interlaced.

2 Casing, System Boards and Video Video Options
Video Controller and Video Memory on a Video Card
Product D4471A is supplied with 2 MB of video memory on a Matrox MGA Millennium card, which can be increased to 4 MB or 8 MB. This PC does not use the integrated video controller and memory. The card is in a PCI slot.

The following video resolutions are typically available.

640 x 480 256, 64K, 16M 60 - 120 2 MB
800 x 600 256, 64K, 16M 60 - 120
1024 x 768 256, 64K, 16M 60 - 120 4 MB
1600 x 1200 1 256, 64K 60 - 72
1280 x 1024 256, 64K, 16M 60 - 90 8 MB
1600 x 1200 1 256, 64K, 16M 60 - 72
1 Upper limit of refresh rate for HP monitors is 60 Hz. 2 Bpp = Bits per pixel

2 Casing, System Boards and Video Video Options
Video Controller on the System Board and Video Memory that is Shared Main Memory
Some PCs have a video system that uses Unified Memory Architecture (UMA). What this means is that the video controller does not use dedicated video memory, but instead uses a portion of main memory as video memory.
The amount of “shared” memory can be set to either 1 MB or 2 MB. To do this, use either the Video Memory Size item in the Setup program, or the HP Dynamic Video Feature which is accessible via the Windows 95 Control Panel.
The following video resolutions are typically available.
Resolution Number of colors Refresh Rate (Hz) Memory
640 x 480 16 60 1 MB
640 x 480 256, 64K 60, 72, 75, 85
800 x 600 256, 64K 56, 60, 72, 75, 85
1024 x 768 256 i431 60, 70, 75, 85
640 x 480 16 60 2 MB
640 x 480 256, 64K, 16M 60, 72, 75, 85
800 x 600 256, 64K, 16M 56, 60, 72, 75, 85
1024 x 768 256, 64K i431, 60, 70, 75, 85
1280 x 1024 16, 256 i431, 60, 72, 75, 85
1 Interlaced.

The HP Vectra 500 Series PC (models 520 and 525) multimedia and commu- nications option comes with an audio fax/data modem (an Aztech AT3300 card). This chapter describes the audio and communications features of the card.

3 Multimedia and Communications Aztech AT3300 Connections
The Aztech AT3300 audio fax/data modem incorporates built-in advanced communication and audio telephony features, including the capability to perform simultaneous audio playback and recording, as well as hands-free communication.
Telephone Connections for the U.S., Canada and Spain
The Aztech AT3300 audio fax/data modem only has one external connection so a splitter cable (delivered with the PC) is required to connect the telephone line and handset. The connections are shown below.

Telephone Handset is connected here Telephone extension cord is connected here

3 Multimedia and Communications Aztech AT3300 Connections

Telephone line cable which is specific to each country
Connecting Audio Devices to the Rear Panel
Details on the use of each socket on the rear panel are given below:
TEL Connection for a telephone line.
LINE IN Connection for devices such as a cassette, DAT, or Minidisc player.
MIC Connection for a microphone.
LINE OUT Connection for speakers, an external amplifier for audio
output, a recording device (tape deck) or headphones for audio output.
JOYSTICK Connection for a joystick (for game software) or
MIDI instrument.
International Telephone Connections

3 Multimedia and Communications Aztech AT3300 Connections
The following figure shows how to connect the headset to the Aztech AT3300 audio fax/data modem.

Connecting the Headset

3 Multimedia and Communications Aztech AT3300 Connections
Aztech AT3300 Internal Connections
The Aztech AT3300 audio fax/data modem has several connectors that allow it to be connected to other devices.
U.S. and Canada Internal Connections
The following figure shows where the internal connectors are located on the U.S. and Canada version of the Aztech AT3300 audio fax/data modem.


3 Multimedia and Communications Aztech AT3300 Connections
The following figure shows where the internal connectors are located on the international version of the Aztech AT3300 audio fax/data modem.

International Internal Connections

3 Multimedia and Communications Aztech AT3300 Connections
The audio fax/data modem has an on-card connector for the MIDI synthesizer called Wave Blaster. This daughtercard module is capable of producing extremely high-fidelity stereo music for computer audio systems.
There are two CD Audio Connectors, one labeled “CDAUDIO 1” and one labeled “CDAUDIO 2”. These connectors allow the audio fax/data modem to be connected to the CD-ROM drive via the audio cable. Either connector can be used. If one connector is already selected for the CD Audio, the second connector can be used to connect an external sound device.
The TV Audio Connector allows an internal TV audio input from an optional internal TV card to be connected.
The Radio Connector allows an internal audio input from an optional internal radio card to be connected.
This connector determines the microphone type. It is preconfigured and should not be modified.
The Microphone Connector is a 3-pin connector that accepts microphone input. It has the same functions as the external microphone connector (refer to “Connecting Audio Devices to the Rear Panel” on page 17). However, only one connector can be selected. If the external microphone is used, for example, the internal connector is disabled.
The LOUT Connector has the same function as the external line out connector (refer to “Connecting Audio Devices to the Rear Panel” on page 17). However, only one connector can be selected. If the external line out is used, for example, the internal connector is disabled.

3 Multimedia and Communications Communications Software
Multimedia and communications models are preloaded with a comprehensive set of communications and sound tools.
The communications software performs a wide range of communications tasks, such as sending and receiving faxes, answering and screening phone calls, and recording voice messages.

This chapter gives details of the displays which are recommended for the HP Vectra 500 Series PCs (models 520 and 525).

There are no displays delivered with the HP Vectra 500 Series (models 520 and 525). There is, however, a list of recommended displays. These are listed by region in the following table.
Display Size Europe US and Canada
14-inch D2811A D2813S D2811A D2810A
15-inch D2808S D2808S D2808A D2808A
17-inch D2817A
Displays for SBSO can be recognized by the ‘S’ in the part number (for example, D2808S). SBSO displays come with customized documentation, packaging and warranty.

HP Vectra 500 Series PCs come preinstalled with a range of software.

5 Preinstalled Software Software Packages
The following table shows the software packages delivered with HP Vectra 500 Series PCs (models 520 and 525).
Preinstalled Software Available Localizations1
Adobe Acrobat Reader 2.1 Microsoft Word Microsoft Office Microsoft Excel Microsoft Powerpoint
QUIP Proshare TIMTEL HP Message Sender V2.0 PC411 Microsoft Exchange
US
Carbon Copy Remote Support 3.0A HP Vectra PC Checkup (low-level hardware diagnostics) McAfee VirusScan95 Scandisk Safe Off Datasafe Remote Backup US
CompuServe America On Line Infovia T-Online Netcom/Netscape
Setup HP Registration Card Start Up Sequence
HP Learning HP Welcome Center HP Help
HP Uninstall 2.0

5 Preinstalled Software Software Packages
Printer Drivers Video Drivers LAN Ready
1US=United States of America, FR=France, GR=Germany, SP=Spain, UK=United Kingdom
All software may be restored using CD-ROMs included with each PC. Version numbers are correct at time of printing.
Peripherals



This chapter briefly outlines the support tools available for the HP Vectra 500 Series PCs (models 520 and 525).

6 Support Tools Software Recovery
All HP Vectra 500 Series PCs are delivered with a product recovery kit which consists of:
The HP Product Recovery CD-ROM may be used to restore all the software (except business applications).
The software recovery process takes between 60 and 90 minutes— depending on the computer’s configuration.
The HP Product Recovery CD-ROM also includes the Scandisk utility which can be used to check the hard disk surface, files and folders for damage. The CD-ROM also enables the following floppy disks to be created:
All HP Vectra 500 Series PCs sold with the multimedia and communications option are delivered with a restricted version of Carbon Copy.
Carbon Copy allows HP Support personnel to connect and remotely control a client’s PC in order to perform high-level troubleshooting. This tool is extremely powerful and should be used only by qualified HP Support Center personnel, and only after consent from the client.
MicroCom Carbon Copy

6 Support Tools Software Recovery
HP Vectra PC Checkup
The HP Vectra 500 Series PCs are equipped with a low-level hardware diagnostics program which can be used to identify hardware-related problems. See the next section, The HP Checkup Program for more information.
The HP Vectra 500 Series PC Service Handbook containing service information and part numbers is available.
Updated part number information is also available on the HP-SPI CD-ROM.
Service Handbook

6 Support Tools Running the HP Vectra PC Checkup
HP Vectra 500 Series PCs are equipped with a checkup program which can be used to identify and fix hardware-related problems. (The checkup program is an enhanced version of the diagnostics toolkit which was delivered with the Spring 1996 models—models 510 and 520.)
Generating an HP Vectra PC Checkup Disk from Within Windows 95
To generate a checkup disk you will need a blank floppy disk available.
1 Click the Start button in the bottom left corner of the screen.
2 Click Programs, then HP Support Utilities, then Diagnosis, then Create Your PC Checkup Disk.
3 Follow the instructions on the screen.
Generating an HP Vectra PC Checkup Disk from the Product Recovery CD-ROM
Refer to the instructions supplied with the Product Recovery CD-ROM.
Running the HP Vectra PC Checkup from a Floppy Disk
1 Shut down the PC in the normal way if you can.
2 Turn off the PC.
3 Insert the checkup program floppy disk that you have created.
4 Turn on the PC.
5 Follow the instructions on your screen.
Running the HP Vectra PC Checkup from the Hard Disk
1 Close down all applications if you can, as the checkup program first exits from Windows 95.
2 Click Start.
3 Point to Programs, then HP Support Utilities, then Diagnosis.
4 Click Run your PC Checkup.
5 Follow the instructions on your screen.



HP Part No. 5964-8384-EN

I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.