Manuale d’uso / di manutenzione del prodotto Bearcat 880 del fabbricante Uniden
Vai alla pagina of 22
O wner ’ s Manual Printed in China U01UT390ZZA(0) ® 880.
CONTENTS SAFETY NOTICE ........................................................................... 4 UNPACKING ................................................................................. 4 DESCRIPTION ............................................
Uniden is a register ed trademark of Uniden America Corporation. Bearcat is a reg istered trademark of Uniden America Corpora tion. Features , specications, and availability of optional accessories are all sub ject to change without notice. RF Pow er Check .
4 SAFETY NOTICE The antenna used f or this radio must be properly installed and maintained and must pro vide a separation distance of at least 34 cm (13.4 Inches) from all persons and must not be collocated or oper ated in conjunction with any other antenna or tr ansmitter .
5 Communications C ommission (FC C). Any adjustments or alterations which would alter the performa nce of the transc eiver's original FC C t ype acceptance , or which would change the frequency determining method, are strictly prohibited.
6 T alkback: T alk back lets you monitor y ourself when transmitting. Pr ess T alkback to activate the function (LED = on). W ith T alk back active, press P TT and adjust the volume with the V olume Control knob. (L evels 00 - 15) MIC Gain: Adjusts microphone sensitivity .
7 11. MEM/SCAN : Pr ess to start or stop scanning modes [All Channel Scan (see page 10) and Memor y Scan (see page 12)]. Press and hold to set or clear channel memory while in M emor y mode. 12. 9/19/NORM : Pr ess to switch between emer gency channel 9, channel 19, and standard CB channels .
8 INSTALLATION MOBILE INST ALLA TION Plan the location of the transceiver and microphone brack et b efore beginning installation. 1. Select a location that is convenien t for operating the r adio but does not interfere with the driver or passenger . 2.
9 caution must be taken to prev ent a short circuit. If in doubt, contact your vehicle dealer f or information. Ground Information This transceiver may be installed and used in any 12-v olt DC negative ground system vehicle .
10 USING YOUR BEARCAT 880 CB MODE Be sure that the power source , antenna, and microphone are properly connec ted before proceeding. BASIC SETTINGS 1. T urn unit on. Set volume to a comfortable level. 2. Select channel. 3. Set noise limitations as desired ( ANL/NB ).
11 scanning in the selected direction. • T o change to Memor y Channel Scan mode, press MEM/S CAN while in All Channel Scan mode (see page 12). 3. T o exit All Channel Scan mode, press P TT , 9/19/NORM , WEA THER , or CB/P A . WEA THER MODE WX MODE Y our radio combines a CB radio with a W eather radio and a W eather Alert system.
12 Set W eather Aler t Mode W eather Aler t mode only operates when you ar e in CB mode; it does not operate in W eather mode . In CB mode, the radio sounds an alert tone when it detects a 1050Hz tone on a weather channel. Pr ess and hold WEA THER to turn W eather Aler t on.
13 MENUS Acc ess menus by pressing MENU/OK . The first menu, COL OR, displays. T urn the Channel Selec tor knob to c ycle thr ough the other menus: C OL OR - Back light color C ONT - L CD Cont.
14 Set L CD Contrast 1. Pr ess MENU/OK to activate the menus. T urn Channel Selec tor until CONT displays . 2. Pr ess MENU/OK . T ur n Channel Selec tor until DAY display s. 3. Pr ess MENU/OK . DAY blinks. 4. T urn Channel S elector to c ycle thr ough the contrast options .
15 – FAILHI - Voltage is t oo high. 3. Pr ess MENU/OK to return to the DIAG lev el. Antenna Mismatch Check An antenna mismat ch indicates that r eception quality may be impaired . 1. Once DIAG displays , press MENU/OK; VOLT displa ys. 2. T urn Channel S elector until ANT displays.
16 the microphone to see the RF output po wer levels . Release PTT to see incoming signal str engh. Calibrat e Standing W ave Ratio (SWR) Check and calibrate the SWR t o ensure that you ar e using pow er effectively . 1. Pr ess S/RF/CAL/SWR until CAL and a vertical status bar display on the L CD screen to indicate y ou are in Calibra tion mode.
17 Use only the fuse specied for your Bearcat 880. Failure to do so may v oid your warranty . TROUBLESHOOTING In the event of system malfunction, per form the f ollowing proc edures: Problem Suggestion Unit does not power up Check power cor d connections.
18 If you do not get satisfactor y results after per forming these checks , call the Uniden Customer Service Center at 1-800-297-1023, 8:00 a.m. t o 5:00 p .m. CST , M onday thr ough F riday . SERVICING YOUR TRANSCEIVER T echnical information, diagrams , and charts are provided on request .
19 Hum and Noise: Better than 40 dB Fr equency T olerance: ±0.002% Modulation Per centage (P eak): 100% Spurious Rejection: -70 dB Output Impedance: 50 ohm, unbalanced RECEIVER Sensitivity at 10 dB S+N/N: 0.5 µV Sensitivity at 500 mW Audio Output: 0.
20 not manufactured by Uniden, or (F) installed or programmed b y anyone other than as detailed by the owner’ s manual for this product. ST A TEMENT OF REMED Y : In the event that the product does n.
21 RADIO CODE DEFINITIONS The follo wing list contains common “10- Codes ” used by CB r adio operators f or faster communication and bett er understanding.
Code Meaning Code Meaning 10-27 I am moving to channel 10-85 My address is 10-28 Identify your station 10-91 T alk closer to microphone 10-29 Time is up for c ontact 10-93 Check my frequency on this c.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Uniden Bearcat 880 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Uniden Bearcat 880 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Uniden Bearcat 880 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Uniden Bearcat 880 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Uniden Bearcat 880, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Uniden Bearcat 880.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Uniden Bearcat 880. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Uniden Bearcat 880 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
