Manuale d’uso / di manutenzione del prodotto ANA 9710 del fabbricante Uniden
Vai alla pagina of 46
ANA 9710 900 MHz Analog PBX Cordless Telephone Operating Guide ®.
One Year Limited Warranty WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.
Covered under one or more of the following U.S. patents: 4,511,761 4,523,058 4,595,795, 4,597,104 4,797,916 4,803,491 5,381,460 5,426,690 5,434,905 5,491,745 5,533,010 5,574,727 5,650,790 5,660,269 5,661,780 5,663,981 5,671,248 5,717,312 5,754,407 5,787,356 5,794,152 5,838,721 and other patents pending.
PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture.
Handset Controls & Functions 1. Ringer ON/OFF switch 2. Message Display 3. Hold ( hold ) Key 4. Talk ( talk ) Key 5. Numeric Keypad 6. Pause ( pause ) Key 7. Redial ( rdl ) Key 8. Microphone 9. Head Set Jack 10. Volume ( r/vol ) Key 11. Mute ( mute ) Key 12.
Base Unit Controls & Functions 18. DC Power Jack 19. Hold ( hold ) Key 20. Page/find ( page/find ) Key 21. Tone/Pulse Switch.
Uniden® is a registered trademark of Uniden America Corporation. AutoStandby™ and AutoTalk™ are trademarks of Uniden America Corporation. AutoStandby is a patented invention of Uniden America Corporation. 1 TABLE OF CONTENTS Important Safety Instructions .
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Read and understand all instructions.
D. If the product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage, and will often require extensive work by a qualified technician to restore the product to normal operation.
About Your ANA 9710 Congratulations on your purchase of the Uniden ANA 9710 Cordless Telephone. The ANA 9710 is designed and engineered to exacting standards for reliability, long life, and outstanding performance. It is designed to work with a PBX system.
Important Electrical Considerations Warning: Please do not attempt to unplug any appliance during an electrical storm. Unplug all electrical appliances when you know an electrical storm is approaching. Lightning can pass through your household wiring and damage any device connected to it.
Radio Interference Radio interference may occasionally cause buzzing and humming in your cordless Handset, or clicking noises in the Base Unit. This interference is caused by external sources such as a TV, refrigerator, vacuum cleaner, fluorescent lighting, computer equipment, or electrical storm.
ANA 9710 Features Super Long Range 900MHz Digital Spread Spectrum 2-line, 16-digit LCD Display Headset Jack Ringer Volume Control Handset Volume Control Single button access to: CONFERENCE , HOLD , an.
Installing Your ANA 9710 Selecting the Installation Location Select a location for the ANA 9710 that avoids excessive heat or humidity. The Base Unit of your ANA 9710 can be placed on a desk or tabletop near a standard 120V AC outlet and telephone line jack.
Connecting the Telephone Cords The ANA 9710 must be connected to an analog PBX port or a standard analog telephone line. CAUTION: Never install telephone wiring during a lightning storm. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
Tone/Pulse Switch Be sure the TONE/PULSE switch is in the TONE position. Note: Most systems are Tone dialing. Check with your PBX Administrator if you are not sure whether your system is Tone or Pulse dialing.
IMPORTANT! Place the power cord so that it does not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards. Note: If you cannot plug the AC Adapter into the outlet, contact someone about replacing the outlet.
Wall Installation Standard Wall Plate Mounting This Phone is designed to be mounted on a standard AT&T or GTE wall plate. To attach the wall mount stand to the Base Unit: 1. Slide the Wall Mount stand into the notches at the top of the Base Unit, push the Wall Mount stand down and snap it into place.
6. Place the Base Unit on the posts of the wall plate and push down until it’s firmly seated. 7. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Do not use an outlet controlled by a wall switch. Direct Wall Mounting If you do not have a standard wall plate, you can mount your phone directly on a wall.
1. Insert two mounting screws into the wall 3-15/16 inches apart. Allow about 3/16 of an inch between the wall and screw heads for mounting the phone. 2. Plug and secure the AC Adapter cord by following steps 2 and 3o ft h e Standard Wall Plate Mounting.
5. Plug the other end of the short telephone cord into a telephone wall jack. 6. Plug the AC Adapter into a standard 120V AC wall outlet by following step 7 of the Standard Wall Plate Mounting. Charging Unit Wall Mounting The Charging Unit is also designed to be wall mounted.
3. Place the Charging Unit on the posts of the wall screws and push down until it is firmly seated. 4. Plug the AC Adapter into a standard 120V AC wall outlet.
Attaching the Beltclip to the Handset You can use the Beltclip to attach the Handset to your belt or pocket for convenient portability. 1. Slide the clip into the tab slot. ( CAUTION: The Beltclip is designed to fit snugly onto the Handset.) 2. Press firmly until it snaps into place.
3. To remove, simply press the retain clip in toward the Beltclip blade and slide the clip up at the same time. Installing the Handset Battery Pack 1. Remove the battery cover by pressing the latch and sliding the cover down until it comes off the Handset.
3. Securely close the battery compartment cover by sliding it up until it snaps into place. Charging the Handset Battery Pack The Rechargeable Nickel-Cadmium Battery Pack must be fully charged before using your ANA 9710 for the first time. ( Note: Charge the Battery Pack without interruption for 5 hours.
Charging Spare Battery Packs The Charger Unit of your ANA 9710 is equipped to charge the Spare Battery Pack with or without the Handset in the front slot. 1. Slide the Spare Battery Pack into the second slot in the Charging Unit until the retaining clip snaps over the top of the pack.
Cleaning the Battery and Charging Unit Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset, Spare Battery Pack and Charging Unit about once a month. Use a pencil eraser or a soft dry cloth. Do not use any liquids or solvents.
ANA 9710 Handset Controls Earpiece Volume Press r/vol on the side of the Handset during a call to change the earpiece volume on the handset. 22.
Handset Ringer tone and volume Press r/vol on the side of the Handset in Standby mode to select seven ringer tones and volume combinations. Vibrate Mode “Ring off” shown on the above display is the Vibrate Mode. If you set the ringer off and the Handset is not on the charger, the Handset will vibrate when there is an incoming call.
Using the Handset When you pick up the Handset and press talk , you will see: After the connection has been made between the Handset and Base, you will see: Or, you may see one of the following: Condi.
Answering a Call When you receive a call, the Handset rings and you will see: Handset in the Charging Unit Handset out of Charging Unit Pick up the Handset. The AutoTalk feature allows you to answer the call immediately. Press talk When you finish the call, place the Handset back in the Charging Unit.
Feature Buttons Note: The exact operation of the Feature Buttons depends on how your PBX system is configured. Contact your PBX Administrator for more information. Placing a call “on hold” Press hold . You will hear a “beep” and see: To resume the call, press hold or talk .
Programming the Feature Buttons The Transfer and Conference Keys can be programmed for special use, such as causing a “Hook Flash” followed by a special number or function. For example — to program the xfer key for “Hook Flash” and 9 for outside transfers only: Press mem .
Function Keys HOLD Press once, you will hear a “beep” and the call is placed on hold. Press hold or talk to resume the call (local hold). XFER Press xfer (Transfer) , you will hear a “beep”. CONF To connect a second party to a call in progress, press conf (CONFERENCE) .
Using Your ANA 9710 Memory Use these buttons to operate the ANA 9710 Memory Storing a Number 1. Press mem . You will hear a beep, and see the message: 2. Enter the number (up to 20 digits) you want to store. a. To program a Pause in the dialing sequence, press pause .
5. The ANA 9710 then returns to Standby mode. Example: Store 555-1234 in memory location 12: A. Press mem . B. Enter 5551234 . C. Press mem . D. Press 12 . The Handset beeps. This is confirmation that you have programmed 5551234 into memory location 12 and you will see: The phone then returns to Standby.
Dialing with a Stored Number Note: The following applies when the phone is in Standby Mode, and you have already established a connection between the Handset and Base Unit. 1. Press talk . 2. Press mem . 3. Enter the Memory Location (01 - 20). The phone automatically dials the number shown.
C. Pressing the mute key, you will move down through the Memory (20 to 1). Pressing r/vol you will move up through the Memory (1 to 20). Press r/vol or mute until you reach the desired Memory Location. 4. Once you have the desired number, press talk .
Using Your ANA 9710 Base Unit Although most of the ANA 9710 operations are performed at the Handset, there are two operations performed at the Base Unit.
Optional Headset (EXP9530) The optional Headset provides a “Hands-Free” Option for the ANA 9710. With the Headset installed, you can use the Beltclip to carry the Handset, and conduct a conversation using the Headset. To install the optional Headset, open the cover over the Headset Jack and plug the Headset in.
Using an Optional Second 2500-type Analog Telephone Analog Telephone A standard 2500-type Desk telephone can be used with the ANA 9710 . Calls can then be answered with the Desk phone and transferred to the ANA 9710. Note: A special Security Feature disconnects the Desk phone whenever the ANA 9710 Handset is in use .
Typical Applications You can use the ANA 9710 together with a standard PBX telephone to give you effective business communications both at your desk and away from it. Contact your PBX Administrator for more information about your System. You can have your PBX system programmed so the following sequence occurs: 1.
Optional Accessories and Replacement Parts For the following Optional Accessories and Replacement Parts contact your PBX Administrator. 37 EXP9704 AC Adapter for Base Unit Telephone Cord Beltclip EXP9.
Troubleshooting If your ANA 9710 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact your PBX Administrator. Note: Do not attempt to service this unit yourself.
Specifications General: The ANA 9710 complies with FCC and IC parts 15 and 68. Frequency Control : Phase Lock Loop Modulation : Spread Spectrum Operating Temperature : 0° to 50° C (+32° F to +122° F) Base Unit Receive/Transmit Frequency : 902 MHz to 928 MHz Power Requirements : 10V DC from supplied AC Adapter Size : 4 1/4 in .
MEMO 40.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Uniden ANA 9710 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Uniden ANA 9710 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Uniden ANA 9710 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Uniden ANA 9710 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Uniden ANA 9710, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Uniden ANA 9710.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Uniden ANA 9710. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Uniden ANA 9710 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
