Manuale d’uso / di manutenzione del prodotto 42HP82 del fabbricante Toshiba
Vai alla pagina of 50
Wide Plasma Display TOSHIBA CORPORATION, 2002 42HP82 O WNER'S M ANUAL Owner's Record The model number and serial number are on the back of your display. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this display.
2 Precautions Please read this manual carefully before using your T OSHIBA plasma display and keep the manual handy for future reference. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK.
3 NOTE: When you connect a computer to this display , attach the supplied ferrite cores. If you do not do this, this display will not conform to mandatory FCC standards. T o attach the ferrite cores: Set the ferrite cores on both ends of the DVI cable (not supplied), and both ends of the power cable (supplied).
4 Important Information ...................................... 2 How to Attach Options to the Plasma Display ..... 5 Introduction ..................................................... 6 Introduction to the 42HP82 Plasma Display ................. 6 The features you’ll enjoy include: .
5 Y ou can attach your optional mounts or stand to the plasma display in one of the following two ways: • While it is upright. (See Drawing A) • As it is laid down with the screen face down (See Drawing B).
6 Introduction to the 42HP82 Plasma Display TOSHIBA ’ s 42HP82 Plasma Display is a seamless blend of cutting-edge visual technology and sophisticated design. At 42 inches, with a 16:9 aspect ratio, the 42HP82 certainly makes a big impression. However , at a mere 3.
7 Front View Par t Names and Function PROCEED INPUT SELECT / EXIT DOWN UP LEFT/ - RIGHT/ + VOLUME POWER/STANDBY PROCEED INPUT SELECT / EXIT DOWN UP LEFT / - RIGHT / + VOLUME POWER / STANDBY 7 6 5 4 1 3 2 q Power T urns the display ’ s power on and of f.
8 AC IN RGB 3 ( Digital RGB ) SPEAKERS MUST HAVE MORE THAN 7WATT RATING IMPEDANCE 6 OHM RIGHT LEFT VIDEO 1 VIDEO 2 REMOTE CONTROL RGB 1 L ( MONO ) L ( MONO ) G/Y /VIDEO 3 HD VD R R Y L ( MONO ) R EXTE.
9 Remote Controller q POWER ON/OFF Switches Power ON/OFF . (This does not operate when POWER/ST ANDBY indicator of the main unit is off.) w RGB/PC Press this button to select RGB/PC as the source. The available sources depend on the setting of “ BNC SELECT ” .
10 Battery Installation and Replacement Insert the 2 “ AAA ” batteries, making sure to set them in with the proper polarity . 1. Press and open the cover . 2. Align the batteries according to the (+) and ( – ) indication inside the case. 3.Replace the cover .
11 PROCEED INPUT SELECT / EXIT DOWN UP LEFT/ - RIGHT/ + VOLUME POWER/STANDBY Appro x. 23ft / 7m Using the wired remote control mode Connect the supplied remote cable to the remote controller ’ s remote jack and the “ REMOTE CONTROL ” terminal on the display .
12 Installation RGB 3 ( Digital RG B ) VIDEO 1 VIDEO 2 REMOTE CONTROL CONTROL LOCK ON / OFF RGB 1 R/C R/PR L ( MONO ) L ( MONO ) G/Y / VIDEO 3 B/C B/PB HD VD R R Y CB / PB CR / PR L ( MONO ) R EXTERNA.
13 Connecting Y our PC Connecting your PC to your plasma display will enable you to display your computer ’ s screen image for an impressive presentation. The plasma display supports the signals described on page 43. T o connect a PC or compatible graphics adapter: 1.
14 External Speaker Connections External speakers (optional) may be connected to the plasma display to reproduce sound from VIDEO, DVD or RGB signal sources. External speakers may be connected directly to the SPEAKER terminals or indirectly by connecting a stereo system amplifier to the audio outputs.
15 Pin Assignments and Signal Levels for 15-pin RGB (Analog) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 5 4 3 2 1 15 14 13 12 11 10 9 8 7 6 RGB 3 1 9 17 2 10 18 3 11 19 4 12 20 5 13 21 6 14 22 7 15 2.
16 POWER T o turn the unit ON and OFF: 1. Plug the power cord into an active AC power outlet. 2. Press the POWER ON button to turn on the unit. The display ’ s POWER/ST ANDBY indicator will light up (green) when the unit is on. 3. Press the POWER OFF button (on the remote controller or the unit) to turn off the unit.
17 OFF TIMER T o set the off timer: The off timer can be set to turn the power of f after 30, 60, 90 or 120 minutes. 1. Press the OFF TIMER button to start the timer at 30 minutes. 2. Press the OFF TIMER button to the desired time. 3. The timer starts when the menu turns off.
18 W atching with a wide screen (manual) W ith this function, you can select one of four screen sizes. When watching VCR ’ s or DVD 1. Press the WIDE button on the remote controller .
19 Information Supported resolution See page 43 for details on the display output of the various VESA signal standards supported by the display . When 852 (848) dot 480 line wide VGA* signals with a vertical frequency of 60 Hz and horizontal frequency of 31.
20 Menu Operations The OSD window is displayed with respect to the screen as shown on the diagram. • Depending on the screen ’ s mode, the OSD may be displayed differently .
21 Main menu Sub menu Functions Default Reset PICTURE CONTRAST Adjusts the contrast. Center Y es BRIGHTNESS Adjusts the brightness. Center Y es SHARPNESS Adjusts the sharpness. Center/1 Y es COLOR Adjusts the color . Center Y es TINT Adjusts the tint.
22 Picture Settings Menu Adjusting the picture The contrast, brightness, sharpness, color and tint can be adjusted as desired. Example: Adjusting the contrast Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
23 Setting the picture mode according to the brightness of the room There are four picture modes that can be used effectively according to the environment in which you are viewing the display . Example: Setting the “ THEA TER ” mode Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
24 Setting the color temperature Use this procedure to set color tone produced by the plasma display . Example: Setting “ 1 ” (See chart at right) Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then..
25 Adjusting the color to the desired quality Use this procedure to adjust the white balance for bright pictures and dark pictures to achieve the desired color quality . Example: Adjusting the “ WHITE BALANCE ” Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
26 Reducing noise in the picture Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture quality is poor . Example: Setting “ NR-3 ” Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
27 Sound Settings Menu Adjusting the treble, bass and left/right balance The treble, bass and left/right balance can be adjusted to suit your tastes. Example: Adjusting the bass Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
28 3. Adjust using the and buttons. V – POSITION • If neither the or button is pressed within 5 seconds, the current setting is set and the previous screen reappears. T o continue making other computer image adjustments ... Repeat from step 2.
29 Information Adjusting the Auto Picture ON ................... The Picture ADJ and Fine Picture adjustments are made automatically . OFF ................. The Picture ADJ and Fine Picture adjustments are made manually . Adjusting the position of the image V -POSITION .
30 Adjusting the position of the menu display Use these operations to adjust the position of the menus that appear on the screen. Example: Adjusting the position of the menu display Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
31 Setting the power management for computer images This energy-saving (power management) function automatically reduces the monitor ’ s power consumption if no operation is performed for a certain amount of time.
32 POWER/ST ANDBY indicator Power management mode On Standby Suspend Off POWER/ST ANDBY indicator Green Orange Red Red Description Horizontal and vertical synchronizing signals are present from the computer . No horizontal synchronizing signals are sent from the computer .
33 Setting the gray level for the sides of the screen Use this procedure to set the gray level for the parts on the screen on which nothing is displayed when the screen is set to the 4:3 size. Example: Adjusting the “ GRA Y LEVEL ” Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
34 Setting RGB3 ADJ. When the picture input from the RGB3 input terminal is distorted, select the most appropriate setting from among “ 1, ” “ 2, ” and “ 3. ” Example: Setting “ 2 ” Pr ess the PROCEED button on the r emote contr oller to display MAIN MENU on the scr een, then.
35 Information PLE AUTO .............. The brightness of the screen is adjusted automatically to suit the picture quality . LOCK .............. The brightness level is set to minimum. ORBITER OFF ................. Orbiter mode does not function.
36 The 2nd line of the “ WORKING TIME ” : → 0M ↔ 3M ↔ 6M ↔ 9M ↔ ... ↔ 57M ← The 1st line of the “ W AITING TIME ” : → 0H ↔ 1H ↔ 2H ↔ 3H ↔ ... ↔ 12H ← The 2nd line of the “ W AITING TIME ” : → 0M ↔ 3M ↔ 6M ↔ 9M ↔ .
37 Resetting to the default values Use these operations to restore all the picture adjustments, audio settings, to the factory default values. Refer to page 21 for items to be reset. Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
38 Options Settings Menu Setting the allocation of the audio connectors Setting the AUDIO 1, 2, and 3 connectors to the desired input. Example: Setting “ AUDIO 1 ” to “ VIDEO 2 ” Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
39 Setting a computer image to the correct RGB select screen W ith the computer image, select the RGB Select mode for a moving image such as (video) mode, wide mode or digital broadcast. Example: Setting the “ RGB SELECT ” mode to “ MOTION ” Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
40 Setting high definition images to the suitable screen size Use this procedure to set the number of vertical lines of the input high definition image to 1035 or 1080. Example: Setting the “ 1080B ” mode to “ 1035I ” Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
41 Information Menu Checking the frequencies, polarities of input signals, and resolution Use this function to check the frequencies and polarities of the signals currently being input from a computer , etc. Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then.
42 Setting the video signal format Use these operations to set the video signal format. Example: Setting the video signal format to “ 3.58 NTSC ” Pr ess the PROCEED button on the r emote contr oller to display the MAIN MENU on the scr een, then...
43 T able of Signals Suppor ted Suppor ted resolution • When the screen mode is NORMAL, each signal is converted to a 768 dots 768 lines signal. (Except for * 2, * 4 ) • When the screen mode is FULL, each signal is converted to a 1024 dots 768 lines signal.
44 *1 Only when using a graphic accelerator board that is capable of displaying 852 480. *2 Display only 640 lines with the screen center of the vertical orientation located at the center . *3 The picture is displayed in the original resolution. The picture will be compressed for other signals.
45 Symptom Picture is disturbed. Sound is noisy . Remote control operates erroneously . The remote controller does not work. Display ’ s power does not turn on when the remote controller ’ s power button is pressed. Display does not operate when the remote controller ’ s buttons are pressed.
46 Specifications Product Name Plasma Display Product Code 42HP82 Screen Size 36.1"(H) 20.4"(V) inches 918(H) 518(V) mm diagonal 42" Aspect Ratio 16:9 Resolution 1024(H) 768(V) pixels Pixel Pitch 0.04"(H) 0.03"(V) inches 0.
47 FCC ST A TEMENT MODEL:42HP82 FCC ST A TEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
48 Limited United States W arranty for Wide Plasma Display T oshiba America Consumer Products, Inc. ( “ T ACP ” ) and T oshiba Hawaii, Inc. ( “ THI ” ) make the following limited warranties to original consumers in the United States.
49 T oshiba of Canada Limited ( “ TCL ” ) makes the following limited warranties to original consumers in Canada. THESE LIMITED W ARRANTIES EXTEND T O THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS PLASMA DISPLA Y AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
52 (02-06) PRINTED IN JAPAN HEAD OFFICE/191 McNABB STREET MARKHAM, ONTARIO L3R 8H2, CANADA TEL: (905) 470-5400 SERVICE CENTERS/TORONTO: 191 McNABB STREET MARKHAM, ONTARIO L3R 8H2, CANADA TEL: (905) 470- 5400 MONTREAL: 1643, NORTH SERVICE RD.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Toshiba 42HP82 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Toshiba 42HP82 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Toshiba 42HP82 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Toshiba 42HP82 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Toshiba 42HP82, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Toshiba 42HP82.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Toshiba 42HP82. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Toshiba 42HP82 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
