Manuale d’uso / di manutenzione del prodotto N-CC2360 del fabbricante TOA Electronics
Vai alla pagina of 20
NETWORK COLOR CAMERA N-CC2360 INSTRUCTION MANUAL 1. SAFETY PRECAUTIONS .......................... 2 2. LIST OF INCLUDED COMPONENTS AND PARTS ............ 3 3. GENERAL DESCRIPTION ........................ 4 4. HANDLING PRECAUTIONS .....................
2 1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety.
3 Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage. CAUTION When Installing the Unit • Avoid installing the.
4 3. GENERAL DESCRIPTION 4. HANDLING PRECAUTIONS • Do not direct the camera lens to the sun or strong lighting or light reflection. Exposure to direct sunlight could cause the CCD's color filter to deteriorate, leading to image discoloration. • Do not give the camera a great shock or vibration, as this will damage the camera.
5 (1) Power Input Terminal [24 V AC, 24 V DC] Connect this terminal to the 24 V AC or 24 V DC power supply. Note Do not connect 24 V AC or 24 V DC power when using a PoE-compatible hub. (2) Indicators [RDY BUSY ERR] RDY (green): Remains lit during normal operation.
6 Ceiling surface Lock lever Camera mounting bracket (optional) Pedestal Camera mount Camera mount Pedestal Camera mounting bracket (optional) Lock lever Camera mounting bracket (optional) W all surface W all surface LENS 1 3 2 4 Lens connector 1 2 3 4 Lens connector pin No.
7 6mm or less Lens • To avoid damaging the internal sections of the camera's lens mount, be sure that the lens flange is 6 mm or less thick as illustrated on the right. • C-mount lenses must be used in conjunction with the Lens Mounting Adapter CF-5 (optional).
8 7.1. Connection Example PoE compatible HUB Software Decorder 10BASE-T/ 100BASE-TX 10BASE-T/ 100BASE-TX 24V 2 1 24V 12C12C 10/100M PoE AUDIO OUT MONITOR OUT OUT IN CONT ACT RDY BUSY ERR FD/COL LINK /.
9 8. ADJUSTMENT 1. The RDY indicator lights when the power is supplied to the network camera. 2. Connect the monitor output terminal to the monitor so that the picture may be displayed on the monitor. 3. Set the Flicker-reduction switch of the mode switch to "ON" position if flicker is annoying.
10 6. Adjust the iris level • When using the DC input type lens Adjust the iris level on the Camera menu screen's "IRIS" item. 6-1 Check to confirm that Camera menu setting items are selected as follows.
11 F. A D J ANTI - FLICKER NC OFF ON Mode switch Focus adjustment switch Flicker-reduction switch Not used. Mode switch ( factory default ) [ N-CC2360 ] F. A D J ANTI-FLICKER NC ON OFF INITIALIZE RESET OFF ON OFF ON OFF ON OFF ON 9. ABOUT THE MODE SWITCH Set each switch to the position that provides the best picture reproduction.
12 No. 1 2 3 4 5 6 IN 1 IN 2 C OUT 1 OUT 2 C Contact input 1 Contact input 2 COM Contact output 1 Contact output 2 COM T erminal Name Contact name Day/ Night Select Contact input 1 or Contact input 2.
13 1 1. SETTING INITIALIZA TION Network settings can be reset to their factory defaults. 1. Either press the Reset key or switch on the power again while holding down the INITIALIZE key. 2. Continue to press the INITIALIZE key until the Ready indicator has switched from flashing to steady-on mode.
14 12. TROUBLESHOOTING Remedy Supply power independently to the Camera. Confirm that the cable type (category, null modem or straight) is appropriate for the connected port, then connect correctly. If the rough noise is annoying and distracting, lower the AGC level.
15 24 V AC, 50/60 Hz or 24 V DC or PoE (IEEE802.3af) 13 W (at 24 V AC), (8 W: PoE, 350mA: 24 V DC) Screwless connector (Solid cable: ø 0.4– ø 1.2 mm (AWG 26 – 16), Stranded cable: 0.
16 Note: The design and specification are subject to change without notice for improvement. MPEG-4: max. 4 Mbps 5 (MPEG-4: 4, JPEG: 1) In streaming mode: No limit (MPEG-4 only) Password authentication.
17 24 V AC, 50/60 Hz or 24 V DC or PoE (IEEE802.3af) 13 W (at 24 V AC), (8 W: PoE, 350mA: 24 V DC) Screwless connector (Solid cable: ø 0.4– ø 1.2 mm (AWG 26 – 16), Stranded cable: 0.
18 Note: The design and specification are subject to change without notice for improvement. MPEG-4: max. 4 Mbps 5 (MPEG-4: 4, JPEG: 1) In streaming mode: No limit (MPEG-4 only) Password authentication.
19.
133-12-993-90 URL: http://www.toa.jp/.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il TOA Electronics N-CC2360 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del TOA Electronics N-CC2360 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso TOA Electronics N-CC2360 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul TOA Electronics N-CC2360 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il TOA Electronics N-CC2360, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del TOA Electronics N-CC2360.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il TOA Electronics N-CC2360. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo TOA Electronics N-CC2360 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
