Manuale d’uso / di manutenzione del prodotto Oil-Fired del fabbricante BCS
Vai alla pagina of 16
W ARNING Improper installation, adjustment, alteration, service or maintenance can cause serious in- jury or property damage. Refer to this manual. For assistance or additional information, con- sult a qualified installer or service agency .
Page 2 Oil-Fired BCS Storage Capacity (gal.) BTUH (Thousands) Firing Rate (GPH) Hot Outlet T emperature Rise (F) OIL-FIRED BCS Instr uction Manual Return Cold Inlet Recovery (GPH) B D 20e-BCS 20 60 0.
Oil-Fired BCS Page 3 WHEN YOU RECEIVE Y OUR NEW W ATER HEA TER Check the new equipment to see if all components are in good condition and were not damaged in shipment. The water heater and burner may be shipped as separate units. The aquastat and immersion well are packed with the burner .
Page 4 Oil-Fired BCS 1. Cut a 7" O.D. opening in the preferred wall and provide a minimum of 1 ⁄ 2 " clearance of non-combustible space around the Balanced Flue. The opening should allow for a 1 ⁄ 2 " downward pitch to the outside for drainage of any condensate in the Balanced Flue.
Oil-Fired BCS Page 5 CONNECT W ATER PIPING Be careful not to apply any heat to the water heater nipples. Install dielectric unions and shut off valves on both hot and cold water lines. 40 BCS models are equipped with a brass inlet bushing in- stalled in the tank.
Page 6 Oil-Fired BCS FRESH AIR INTAKE VENT Proper sealing of the fresh air intake vent material is important, but temperature is not an issue. Failure to properly seal the inlet venting subjects the burner to possible reverse drafts after burner shutdown— a hazardous condition with the possibility of creating a fire .
Oil-Fired BCS Page 7 CONNECT THE OIL LINE Gravity System: The oil burner is normally equipped with a single-stage pump equipped for one line (gravity) flow . Use 3 ⁄ 8 " O.D. or larger soft copper tubing and attach with flared fittings. DO NOT USE COMPRESSION FITTINGS.
Page 8 Oil-Fired BCS PLA CE W A TER SYSTEM IN OPERA TION 1. Fill the tank with water , opening a hot water faucet to allow trapped air to escape from the heater . Open the cold water inlet valves. Shut off each faucet as it delivers water that is free of air .
Oil-Fired BCS Page 9 MEASURING THE OUTCOMING W ATER TEMPERA TURE, CON’T W ARNING: Hydr ogen gas can be produced in a hot water system served by a heater that has not been used for a long period of time (generally two weeks or more). Hydr ogen gas is extremely flammable.
SERVICE 1. Check the fuel supply , electrical wiring, fuses, and make sure the temperature control is calling for heat. 2. If the motor runs but there is no flame, remove the electrode assembly , clean, readjust, and check the porcelain for cracks. Replace if necessary .
Oil-Fired BCS Page 11 COMP ANY’S RESPONSIBILITY The company’ s responsibility is to repair or replace, at our option, with the prevailing compa- rable Bock model, any part of the equipment, includ.
OUR TO T AL W ARRANTY COMMITMENT W e will not assume, nor authorize any person to assume for us, any other liability in connec- tion with the sale or operation of Bock W ater Heaters.
Oil-Fired BCS Page 13 BOCK OIL-FIRED W ATER HEA TER.
Page 14 Oil-Fired BCS Balanced Flue ™ BURNER WIRE DIA GRAM Models 20, 32,40,51,120,190E-BCS Carlin EZ-T emp Control.
Oil-Fired BCS Page 15 EXP ANSION T ANK (OPTIONAL) IF ANY OF THESE DEVICES ARE USED, A PROPERL Y SIZED EXP ANSION T ANK MUST BE INST ALLED..
Page 16 Oil-Fired BCS Form # 23390 Rev 3 3/2007 BCS AND RADIANT HEA T Radiant heating: An in-floor hot water space heating system A Bock high-efficiency water heater and zoned radiant heating— Bock&Radiant —make perfect partners for cost-effective personal comfort that heats both space and water .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il BCS Oil-Fired è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del BCS Oil-Fired - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso BCS Oil-Fired imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul BCS Oil-Fired ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il BCS Oil-Fired, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del BCS Oil-Fired.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il BCS Oil-Fired. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo BCS Oil-Fired insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
