Manuale d’uso / di manutenzione del prodotto LC3015-2 del fabbricante Theta Digital
Vai alla pagina of 41
Theta LC3015 q 2 Laser Machine User Pre-installation Guide October , 2003 Amada America, Inc. 7025 Firestone Blvd. Buena Park, CA 90621 T el. (714) 739-21 1 1 Fax.
Document title LC3015 Theta Laser Machine User Pre-installation Guide V ersion 031027 (October , 2003) Applies to: LC3015 Theta Laser Machines Printed: 10/30/2003 8:51 AM Revision history: See page 33 W arning A ll work must be completed by qualified personnel.
CONTENTS Pre-Installation Checklist ...................................................................................................... ........i Items to be Obtained: i Placement of the Machine and Components: i Electrical Requirements ii Preparation ii Description of the Major Components .
Machine Dimensions - LC3015 Theta Plan View ......................................................................14 Planning The Location of the Machine ......................................................................................15 The Chiller .
Table of Figures Machine ........................................................................................................................ ...............2 Gas connection kit .....................................................................
Figure 14: Electrical connect 230 V AC ......................................................................................29 Figure 15: Entry point for cables .........................................................................................
Pre-Installation Checklist This form must be completed, signed, and faxed back to Amada’s service department. This is required before installation of your Amada laser can begin . Each of the following items must be completed prior to scheduling a service engineer for installation.
Electrical Requirements Electrical power has been connected to the top of the disconnects for each of the following: q NC cabinet q Laser power supply q Dust collector q Chiller Preparation q Chiller tank has been filled with distilled water only .
Description of the Major Components Y our laser systems will arrive in several crates. The machine and accessories are packaged in one crate. The chiller , dust collection system, gas regulators, and any optional equipment (such as transformers or safety mats) will be crated individually .
Major Components 2 LC3015 Theta User Installation Guide - October, 2003 Machine Gas connection kit Dust Collector AIR SUCTION HOT AIR DISCHARGE AIR SUCTION 78.
Size and W eight of Major Components Ensure that you discuss the following dimensions and weights with your selected rigger , be - fore the delivery of the machine.
Basic Specifications 4 LC3015 Theta User Installation Guide - October, 2003 FEA TURE SPECIFICA TION NC unit Fanuc 160iL (32 bit) Laser Fanuc AF4000 4kW CO 2 Fast Axial Flow Axis T ravel X 120 inches (3050mm) Y 60 inches (1530mm) X 19.6 inches (500mm) U ± 135° (Head T ilt) V ± 370° (Head Rotation) W 0.
Laser and Production Cutting Specifications LC3015 Theta User Installation Guide - October, 2003 5 FEA TURE SPECIFICA TION Fanuc C4000AF CW Power 4,000 W atts Peak pulse power 5,000 W atts Maximum material thicknesses: (maximum sheet size according to weight limitation) Carbon steel 2 (O 2 ) 0.
Supply Requirements 6 LC3015 Theta User Installation Guide - October, 2003 Electrical power supply UNIT RA TING SUPPL Y Machine (CNC) 200V~220 V AC 3 phase 60 Hz (15 Amp, 12 KV A) 200~220 V AC 3 phase.
Other Requirements Air supply ITEM Pressure/V olume ISO8573.1 standard Machine 80 psi at 9 ft 3 /min 4 Class 3-4-3 As cutting gas 140 psi at 35 ft 3 /min 5 Class 3-4-3 Dust collector - T orit DFT3-18 9 scfm at 90-100 psi Class 4-5-5 Dust collector - Farr GS-12 12 scfm at 90 psi Laser Oscillator Gas see laser pre-mix gas specification (p.
Air specifications - ISO 8573.1 standard The standard provides a uniform way to specify air quality in terms of particle size, pressure dewpoint, and oil content.
Laser Pre-mix Gas LC3015 Theta User Installation Guide - October, 2003 9 Laser gas quality is critical to the performance and reliability of the laser . Based on our experi - ence, we recommend BOC’s LASERSHIELD F or AGA ’s LaserMix 21. Call either of these national 800 numbers to locate the supplier closest to you.
Laser Pre-mix Gas Specification 10 LC3015 Theta User Installation Guide - October, 2003 Laser gas quality is critical to the performance and reliability of the laser . Based on our experi - ence, we recommend AGA ’ s LaserMix 21 or BOC’s LASERSHIELD F .
Assist Gas Recommendations The machine has provision for three kinds of assist gases. The assist gas inputs are at the rear of the machine. The inputs are labeled OXYGEN, CLEAN CUT , and AIR. Oxygen is normally used to cut steel and stainless steel. Nitrogen is used to Clean Cut™ stainless steel and aluminum with an oxide free edge.
Machine Dimensions - LC3015 Theta Front V iew 12 LC3015 Theta User Installation Guide - October, 2003 Figure 1: Machine from shuttle end.
Machine Dimensions - LC3015 Theta Side V iew LC3015 Theta User Installation Guide - October, 2003 13 Figure 2: Machine from operator side.
Machine Dimensions - LC3015 Theta Plan V iew 14 LC3015 Theta User Installation Guide - October, 2003 Figure 3: Machine from top.
Planning The Location of the Machine The diagrams following provide the details for positioning your new machine. q No obstacles are allowed in the table travel area, and the machine must be at least 3 feet from any wall or obstruction, and the ceiling must be at least 40" above the top of the machine.
The Chiller The chiller is very important to the reliable operation of your laser cutting machine. q The chiller must be placed so that an adequate flow of air is maintained. q The positioning of the chiller is flexible. T wo lengths of flexible hose and appropriate fittings are provided for connection to the system.
Chiller Dimensions Orion Chiller LC3015 Theta User Installation Guide - October, 2003 17 AIR SUCTION HO T A IR DISCH AR GE AIR SUCTION 63.0" 78.1" (for 4 KW system ) 71.
Dust Collectors The dust collector is very important to the safe operation of your laser cutting machine. It will collect dust and particulate generated by the laser cutting process. More than one dust collector type is available for the machine. Either unit, in standard con - figuration, is suitable for cutting most metallic materials.
LC3015 Theta User Installation Guide - October, 2003 19 Figure 6: Torit DFT3-18, side view.
F arr GS -12 See page 7 for compressed air requirements. 20 LC3015 Theta User Installation Guide - October, 2003 Figure 7: Farr GS-12.
Machine Foundations The machine must be properly secured to a suitable foundation. If an existing floor is used, it must be capable of supporting the weight of the machine. The load bearing and vibrational secifications are listed below . Bearing capacity required 1 124 lb/ft 2 Maximum external vibration / disturbance allowable Max acceleration 0.
Machine F oundations Cross Section These drawings include pockets for the j-bolts (preferred method). If anchors are to be used instead, then the j-bolt pockets may be omitted when preparing the foundation. 22 LC3015 Theta User Installation Guide - October, 2003 178.
F oundation End View LC3015 Theta User Installation Guide - October, 2003 23 6.0” 134” 1" Anti-vibration material 12" 14" 20" 8.3” 42.1” 6.0” Figure 9: Foundation right end view 134” 1" Anti-vibration material 12" 14" 20" 42.
J- Bolt Detail 24 LC3015 Theta User Installation Guide - October, 2003 4 - ANCHOR BOL T J- TYPE 4-H E XN U TM 1 6 4-H E XN U TM 1 6 6-W A S H E R M 1 6 4-J A C KB O L T 4 - HEXAGON NUT M30 x 3.
Lifting Use the lifting eyes provided on the frame. See figure for permitted sling angles. LC3015 Theta User Installation Guide - October, 2003 25 Firgure 12: Lifting the Machine.
Installing The Air Supply The machine must be connected to a compressed air system by hose or pipe. The com - pressed air must be clean and dry . It may be necessary for you to purchase an air drier/filter . Please note the following: q The air flow and pressure requirements are listed on page 7.
Installing The Electrical Power Supply The system requires four separate 3 phase power supplies. Power must be supplied to the CNC unit, the laser, the chiller and the dust collector. Power should be supplied from a line separate from those for welding machines and other processes that produce electrical noise.
28 LC3015 Theta User Installation Guide - October, 2003 1 2 76 4 2 76 4 2 76 4 11 3 33 5 55 X3 H1 H3 SHIELD X2 H2 H2 X1 X0 H3 (ASSUMES PRIMARY ) DEL TA H1 X0 X1 X2 X3 LASER 200-220 VAC CHILLER 200-220.
LC3015 Theta User Installation Guide - October, 2003 29 1 2 76 4 2 76 4 2 76 4 11 3 33 5 55 X3 H3 SHIELD X2 H2 X1 X0 (ASSUMES PRIMARY ) DEL TA H1 H1 H2 H3 X0 X1 X2 X3 LASER 200-220 VAC CHILLER 200-220.
Notes 30 LC3015 Theta User Installation Guide - October, 2003.
CNC power connect, Figure 16 A: Power cable B: Breaker LC3015 Theta User Installation Guide - October, 2003 31 L aser po wer in CNC power i n Ch iller inte rface Dust col lect or int erf ace Figure 15.
Protective Coatings The machine may have protective coatings, possibly including wrapping paper and/or cosmoline or other grease. When present, the wrapping paper must be removed before moving the machine axes. Protec - tive grease or cosmoline must be thoroughly cleaned off before running the machine.
Revision history V ersion Details Initial (May 2001) Initial version Revised dwg p. 22 . Asstd formatting, editing revisions. Oct 01 Revised foundation drawings Jan 03 Electrical supply p.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Theta Digital LC3015-2 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Theta Digital LC3015-2 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Theta Digital LC3015-2 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Theta Digital LC3015-2 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Theta Digital LC3015-2, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Theta Digital LC3015-2.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Theta Digital LC3015-2. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Theta Digital LC3015-2 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
